Alto-Shaam 500-S, 750-S manual CA UTI on, Serv ICE, Trou BL ES Hootin G Manual Control

Page 26

SERV ICE

TROU BL ES HOOTIN G - MANUAL

CONTROL

 

 

 

 

 

 

 

 

Error

 

 

Possible Cause

Code

Description/Results

Service Required

E-10

Air Sensor Fault (shorted)

Air sensor is shorted.

Air sensor defective?

 

 

Inoperative Unit

 

 

 

Test air sensor by placing sensor in ice water bath32°F (0°C) and using an

 

 

 

ohmmeter set on the ohm scale. The readingshould be 100 ohms resistance. If it

 

 

 

is more than 2 ohms higher or lower, sensor needs to be replaced. If Ohm reading

 

 

 

is 100, replace display. If Ohm reading is not 100, replace sensor.

E-11

Air Sensor Fault (open)

Air sensor is open or connection failure.

 

 

Inoperative Unit

Air sensor defective? See above forair sensor test.

E-30

Under temperature

Unit door closed? Door gasket need replacement? Preheat skipped?

 

Oven will not reach set temperature

Unit overloaded or holding frozen product? Defective air sensor orprobe?

 

Defective solid state relay? Badwire connections or open heating cable?

 

 

 

If none of the above, contact Alto-Shaam Service Department.

E-31

Over temperature

Unit has exceeded its maximum allowable set temperature by 25 degrees for at

least 3 minutes. Unit will shut down.

 

 

Unit will shut down

 

 

 

Defective sensor or poor sensor connection?

 

 

 

Defective relay?

 

 

 

Shorted heater element?

 

 

 

If none of the above, contact Alto-Shaam Service Department.

E-70

Configuration error Inoperative Unit

Contact Alto-Shaam Service Department for correct DIP-switch settings.

or

EEPROM Error - Bad Checksum

Contact Alto-Shaam Service Department for help resetting the control.

E-82

 

 

E-83

 

Inoperative Unit

Stuck button on control panel. Check buttons.

E-90

Button shorted

 

Inoperative Control

If control is still inoperative, contact Alto-Shaam Service Department.

 

 

E-91

Input failure

 

Contact Alto-Shaam Service Department.

 

 

 

-AC-

Power Failure

 

Press any key to acknowledge.

 

 

 

 

 

 

 

 

 

 

 

 

This section is provided for the assistance of qualified techni cians only and is not intende d for use by

 

 

untrained o r unauth orized serv ice personn el. If your Alto-Shaam ® unit is not operating properly, check the

 

 

following before calli ng you r Authoriz ed Alto-Shaam®Service Agent:

 

 

Check the power flo w to the unit. Pl ug in outl et? Ci rcuit breaker sw itch at bac k of unit turned on?

 

 

 

Do not attempt to repa ir or serv ice the holding cabinet beyond thi s point. Contact Alto- Shaam® for the

 

 

 

nearest authorized service agent. Repairs made by any other serv ice agents without prior authorization

 

 

 

by Alto-Shaam®will void the warranty o n the unit.

 

 

 

 

 

DANGER

DIS CONNECT UNI T F ROM

POWER SOURCE B EFO RE

CLEANI NG OR SERVI CING.

CA UTI ON

THIS SECTION IS PROVIDED FOR THE ASSISTANCE OF QUALIFIED SERVICE TECHNICIANS ONLY AND IS NOT INTENDED FOR USE BY UNTRAINED OR UNAUTHORIZED SERVICE PERSONNEL.

500-S, 750-S, 1000-S, 1000-UP • I NSTALLATION/OPERATION/SERVIC E MAN UAL • 24.

Image 26
Contents MAI Ntena NCE Inst Allati onOperation Sanitation Deli Very Unpack I NGAU TI on Safety Proc Edures Preca UTI ONSWA Rning NST Allatio N CA U TI O NNo TE SIT E Inst AL L Atio NEXT Erio R D Imensio NS 500-S Electrical ConnectionConnection EXT Erio R D Imensio NS 750-SEXT Erio R D Imensio NS 1000-S Electrical Connection Pass-Through OptionEX T ERI or Dimensio NS 1 000 UP Electrical Connection Reach-inNST Allatio Opti ONS and ACC Essori ESStacking Instr Uctions SI TE INS TallatioRES Trai NT Requirements -MO BIL E Equipment Warn INGLevel ING Risk of Electric ShockSI TE INS Tallatio N Drip TrayDrip Tray Installati on Instructions 1000-UP IT E Inst AL LA TIO NElectr CAL Not EHeatin G Charact Erist ICS User SA Fety Info RmationBefo RE Init IAL USE MIN Utes Before L Ading FOO D OP ErationMA NU AL C ONT ROL Operat ION To Toggle BET Ween Fahren Heit Celsiu SOptio NA L Electr Onic Holding CAB Inet Contr OL SET-UP OP Eratio NOptional Electron IC CON Trol IDE NT if IC AT ION Option AL E Lectronic H Olding Cabinet S Peci AL Feat URE S Heat RecoveryOPT Ional ELE Ctronic Holdi NG Cabinet Contro Perat ION Hacc P Docume NtationEL ECT Roni C CO Ntro L Timer Progra MM in G Tim er Prog ramming Inf ormationGener AL Holding Uideline OL DIN G T EM PE R AT U RE RangeLeaning PR Eventi VE MAI AutionAre a ND Clea Ning NtenanceSevere DAM AGE or Elect Rical Hazard Could Result AreClea Ning NI Tation SA Nitati O N Ervi CE TH ER MOS TAT Accura CYTrou BL ES Hootin G Manual Control CA UTI onServ ICE TR OUB LE Possi BLE C Ause AU TIO NTRO UBL Esho OT ING EL Ectronic Contr OL O P T ION Service PAR TS Ervi SER Vice Part S1000- UP Pass Thro ugh Option UP WIT H Pass Throug H Optio N Bonnet Assembly Manual Control Electronic ControlService VIE W Elect roni c Co ntrol Opt ion 1000 -UPSER VIC E VI EW Manual Control 1000 -UPPage Page Page Page Page Page Page Page Page Page Page Page Limi TE D WA Rrant Y
Related manuals
Manual 51 pages 31 b

750-S, 500-S specifications

Alto-Shaam, a leader in commercial kitchen equipment, has developed the 500-S and 750-S models that exemplify innovation in cooking technology. These models offer versatile cooking solutions for diverse foodservice applications, making them ideal choices for restaurants, catering services, and institutional kitchens.

One of the main features of the Alto-Shaam 500-S and 750-S is their advanced Cook & Hold technology. This unique system allows chefs to cook food at lower temperatures for extended periods, preserving moisture, flavor, and nutrients. Unlike traditional cooking methods, this gentle approach helps reduce shrinkage and enhances the quality of the finished dish. The ability to hold food at precise temperatures means that dishes can be prepared in advance, allowing for better management of peak service periods and minimizing waste.

Both models feature a user-friendly digital control panel that simplifies operation, providing precise temperature control and programmable cooking cycles. The intuitive interface allows operators to set cooking parameters and monitor the process easily, ensuring consistent results every time. The availability of multiple cooking modes, including steam and convection air, expands the versatility of these ovens, allowing for a wide array of cooking applications, from roasting to baking.

The compact design of the 500-S and 750-S makes them an excellent fit for kitchens with limited space, while still offering a generous capacity for food production. Constructed of durable stainless steel, these ovens are built to withstand the rigors of a busy kitchen environment. The easy-to-clean surfaces and removable racks simplify maintenance, ensuring a hassle-free experience for food service staff.

Additionally, both models are equipped with Alto-Shaam's exclusive controlled humidity system. This technology allows for the introduction of humidity into the cooking environment, which helps further enhance the texture and juiciness of cooked products. Operators can adjust humidity levels according to the specific needs of each dish, resulting in consistently superior quality.

In summary, the Alto-Shaam 500-S and 750-S are sophisticated yet user-friendly cooking solutions that leverage advanced technology to provide unparalleled versatility and cooking quality. Their unique features, such as Cook & Hold technology, programmable controls, and humidity options, set them apart as essential tools for any commercial kitchen looking to elevate its food preparation capabilities.