LG Electronics NE-1037, NE-1027 Self Diagnostics Failure Code, Care of Your Microwave Oven

Page 20

Self Diagnostics Failure Code

This oven monitors its operation and displays a Failure Code in the display window when a problem occurs.

What to do when a failure code appears:

CODE

CAUSE

WHAT TO DO

F01

* Overcooked food

* Press Stop/Reset Pad to stop

 

 

beep.

 

* Temperature of exhausted air is too

* Unplug the oven and wait at least

 

high

30 minutes before reconnecting.

 

 

* Wait for the oven to cool down and reset.

 

 

* If a flame is observed, do not open the

 

 

oven door.

 

 

* If normal operation does not resume,

 

 

call the service agent with the

 

 

information of failure code.

 

 

 

F33-34

* Defective sensor circuit

* Unplug the oven and wait more than

 

 

10 seconds before reconnecting.

F44

* When a pad was pressed for more than

* If normal operation does not resume,

 

2 minutes

call the service agent with the

 

* Defective pad or control circuit

information of failure code.

 

 

 

 

 

NOTE: Above codes shown in the display do not indicate all the possible failures on the unit.

Care of Your Microwave Oven

1.Unplug the oven before cleaning.

2.Keep the inside of the oven clean. When food spatters or spilled liquids adhere to the oven walls, wipe with a damp paper towel. Mild detergent may be used if the oven gets very dirty. The use of harsh detergent or abrasives is not recommended.

3.The outside oven surfaces should be cleaned with a damp paper towel. To prevent damage to the operating parts inside the oven, water should not be allowed to seep into the ventilation openings.

4.If the Control Panel becomes dirty, clean it with a soft, dry cloth. Do not use harsh detergents or abrasives on the Control Panel. When cleaning the Control Panel, leave the oven door open to prevent the oven from accidentally turning on. After cleaning, press the Stop/Reset Pad to clear the display window or turn the Timer Select Dial back to zero “0” position.

5.If steam accumulates inside or around the outside of the oven door, wipe with a soft paper towel. This may occur when the microwave oven is operated under high humidity conditions and in no way indicates malfunction of the unit.

6.Clean off the grease and dust on bottom surfaces often. Use warm detergent solution.

7.This oven should only be serviced by qualified person. For maintenance and repair of the oven contact the nearest authorized dealer.

- 19 -

Image 20
Contents Operating Instructions Watts Microwave OvenTable of Contents For Your Safety Unpacking Your OvenMaintenance of Your Oven Placement of Your OvenUsing Your Oven Important Information -- Read Carefully Keeping Your Oven Clean ReheatingStanding Time Babies Bottles and Food JarsHow Does the Microwave Work? ReflectionTransmission AbsorptionOutline Diagram NE-1027 How to OperateMemo Outline Diagram NE-1037 Digital Display Window Indicator LocationsBefore Operating Manual 2 or 3 Stages Heating HeatingManual Single Stage Heating Programmed Heating Example Memory Pad Press the Double Quantity PadExample To program 30 seconds at 500 W for Memory Pad ProgrammingProgramming Memory Pads for Single Stage Heating Programming Memory Pads for 2 or 3 Stages Heating Programming the Double Quantity Pad Press Double Quantity PadTo Release Program Lock Other FeaturesTo Activate Program Lock To Read Program List To Select Beep Tone Options To Read the Cycle CounterCare of Your Microwave Oven Self Diagnostics Failure CodeWhat to do when a failure code appears Cooking/Defrosting Guide Front View Side View Side View with Opened Door Technical SpecificationsNE-1027 NE-1037 Central P.O.Box 288, Osaka 530-91, Japan