Indesit FID10IX/1, FID20IX/1 manual Installation

Page 33

Installation

Electrical Requirements

For your own safety, we recommend that your cooker is installed by a competent person such as one who is registered with NICEIC (National Inspection Council for Electrical Installation Contracting). The cooker should be installed in accordance with the latest edition of the IEE Regulations.

Warning: This appliance must be earthed.

Electrical Connections

The installer must check that the voltage shown on the rating plate corresponds with the house electricity supply. The cooker must be supplied via a suitable double pole isolating switch, having a contact separation of at least 3mm in all poles placed in a readily accessible position adjacent to the cooker. If the cooker is to be wired into a connector unit, this may be positioned behind the cooker providing the following requirements are met:

i)The connector unit must not project from the wall more than 25mm.

ii)The top of the connector must not be more than 130mm above floor level.

Remove the terminal cover at the rear base of the cooker. Pass the cable through the cable clamp and connect to the appropriate terminals provided. Allow sufficient cable for any future servicing. Tighten the screws on the cable clamp and replace the cover. Make main connections in the connector unit or cooker control unit. This appliance conforms to B.S. EN 55014 regarding suppression of Radio and Television reception interference.

A double Pole control switch having a minimum rating of 32 amps should be used to feed the cooker using a suitably rated cable. Where a hob is fitted adjacent to or over the cooker, a 45 amp Double Pole control switch should be used to feed both units via separate suitably rated cables.

We recommend a minimum of 4mm2 PVC insulated twin and earth cable conforming to B.S. 6004 for connection of each appliance.

In all cases adhere to routing details (see fig. 4).

This appliance must not be installed over any other appliance that generates heat such as a plinth heater.

Note: Due to many different types of installation, a mains cable is not supplied with this product. The installer will fit the correct type and length of cable.

Important

It is essential that the lower cupboard is constructed in GB the manner illustrated i.e. having side, back, and roof

panels so joined as to provide no apertures which could permit access to the oven unit when installed.

1. General

The appliance is designed for mounting at a safe level into an oven housing which must be secured to the backing wall.

2. Ventilation

a.The oven housing unit cabinet dimensions must comply with fig. 4.

b.An air gap of 50mm minimum must be provided at the rear of any top or bottom cupboards or shelves (see fig. 1).

c.It is necessary that the cabinets are provided with unobstructed ventilation, i.e. from adjacent cabinetry. This can be done by either raising the base of the cabinets using the adjusting feet (or spacers) or alternatively by providing a slot in the cabinet plinth to the dimensions in fig. 1.

d.The air gap at rear allows the warmed air to pass out of the inner cabinet space. Where it is intended to fit cupboards above the oven unit to ceiling height, it is essential that the warmed air is exhausted through the front of the cabinet (see fig. 1).

e.If an oven unit is installed adjacent to a tall cabinet, steam escaping from the oven when the door is opened could condense on and maybe stain the adjacent surface. To prevent permanent staining, the adjacent surface should be made of a material that is heat resisting and easy to clean. Adjacent tall cabinets should not be deeper than the oven housing cabinet.

3. Final Installation

a.Using a spirit level, check that the housing cabinet is level from side to side and from front to back in its installed position.

b.Correct any unevenness by placing spacers under the bottom of the cabinet. Make sure that the cabinet rests firmly on the floor without rocking.

c.Before the oven is fitted, the cabinet must be firmly secured to the backing wall for stability.

d.The oven unit should now be lifted (this is a two person lift) into the cabinet and pushed fully home.

e.Finally, the oven is secured to the cabinet by means of the four Phillips C/SK Head screws - two through each side trim.

f.Remove all packaging material from the grill and oven interior.

List of loose items:

4 x Phillips C/SK Head No. 6 x 25mm screws.

33

Image 33
Contents Double oven Contents Instructions for Installation and Use Electric built-inIntroduction Technical CharacteristicsSafety Advice Event of a Chip PAN or ANY Other PAN Fire SafetyInformationAlways NeverFeaturesFID20,FID10only These Areas can Become HOT FeaturesFIDM20onlyDegrees F and C TemperatureConversionChartCooling Fan ControlsFID20,FID10onlyOven Interior Lights Slow CookingControlsFIDM20only Main Oven Temperature ControlMultifunction Selector Grill ControlFan Oven OffConventional Oven Half GrillSetting the clock Setting the minute minderProgramming cooking GrillPanandHandle Using the grill pan kitTop Oven Shelf Positioning for Grilling Grill Pan, Food SupportGrill Controls Example OperationwhenusingtheTop Oven forGrillingFID20,FID10ConventionalGrilling Operationwhenusingthe Top Oven for Grilling FIDM20 Shelf Positioning Using the Top Oven as a Convection OvenTop oven/Grill Pilot Light is lit when grill is used OperationwhenusingtheTop OvenasaConvectionOvenTopOvenCookeryNotes Never use the grill setting control a when warming platesPlate Warming TOP Oven UtensilsOvenTemperature Charts-Baking Beef Oven Temperature Charts MeatLamb 80C Poultry Pork 90CTemperatures Main Oven Fan Grilling FIDM20onlyGeneral Recommendations Pork Main Oven Fan Grilling RoastingChartFIDM20onlyGB FAN only Setting FIDM20 and FID20, FID10 Using the Main Oven for OtherFunctionsLight only Setting Defrosting Frozen Meat & PoultryMainOven-Convention OvenFIDM20only Main Oven Fan Oven allModels Oven Positions Main Oven Fan Oven CookeryNotesTemperature and Time To prepare meat and poultry for Roasting in your Fan OvenFrozen Meat and Poultry MainOven TemperatureChart Rich Fruit Cakes Grilling should Never be Undertaken with the Door Closed Grilling ProcedureCleaning GRILL, TOP Oven and Main Oven Care and CleaningCatalytic Oven Liners Top Oven Sides, Main Oven Sides Rear PanelHOW to Clean the Lamp Lens Replacement of the Oven LampOven Doors Cleaning the Doors CareandCleaningSide Opening Doors Drop Down DoorsInstallation Tall Cabinet Ventilation 595mm There MAY be Nothing Wrong IfSomethingGoesWrong?If it Still Wont Work Contact the Service Office UK 08709 066Spare Parts Disposal of your productYear Parts Guarantee Extended GuaranteesFree Helpdesk Service Indesit Service Parts and AccessoriesAppliance Registration Xerox Fabriano

FID10IX/1, FID20IX/1 specifications

The Indesit FID20IX/1 and FID10IX/1 built-in dishwashers exemplify innovation and efficiency in kitchen appliances. Both models are designed to cater to modern households, combining practicality with advanced technology to enhance the dishwashing experience.

The FID20IX/1 features a sleek stainless steel finish, offering a contemporary aesthetic that seamlessly blends with any kitchen decor. Its capacity allows for up to 14 place settings, making it suitable for larger families or anyone who frequently entertains guests. This model boasts multiple wash programs, including Eco, Intensive, and Fast, providing flexibility for various dishwashing needs. The Eco program is particularly noteworthy, as it is designed to use less water and energy, making it an environmentally friendly option.

A standout feature of the FID20IX/1 is the presence of the proprietary Indesit technology known as "Extra Power." This feature enhances the washing performance by providing a more effective clean, particularly useful for stubborn stains and heavily soiled dishes. The dishwasher also comes with an adjustable upper basket, which allows users to customize the interior space to accommodate larger pots and pans.

On the other hand, the FID10IX/1 is a more compact version, perfect for smaller kitchens or for those who require a bit less capacity. It can hold up to 10 place settings while still maintaining essential features found in larger models. Like the FID20IX/1, it offers various wash programs, ensuring that users can select the best option based on the level of dirtiness and the types of dishes being cleaned.

Both models employ the "Half Load" option, which optimizes water and energy usage when washing smaller loads, making them efficient choices for everyday use. Additionally, the whisper-quiet operation of these dishwashers ensures that noise is minimized, allowing for comfortable use even during nighttime hours.

Durability is another hallmark of these Indesit models, with robust construction ensuring long-lasting performance. Their user-friendly interfaces and clear LED displays make operation straightforward even for those who may not be technically inclined. Overall, the Indesit FID20IX/1 and FID10IX/1 provide efficient, versatile, and stylish solutions for modern dishwashing needs.