Unified Brands HY-6G(CE) To Assemble, Gas Solenoid Valve P/N, To Reinstall, Igniter Module P/N

Page 26

main gas valve assembly using an open-ended wrench. Be careful not to move the aluminum tubing excessively, or to bend it.

5.Using a wrench, remove the two bolts that fasten the main gas valve bracket.

6.With a pipe wrench, open the pipe union on the left side of the main gas valve and remove the gas inlet pipe from the manual gas valve.

7.Remove the main gas valve and manual gas valve assembly.

To Assemble:

8.Clean pipe threads and apply compound to all joints being connected.

9.Install the main gas valve in the reverse order of removal (Steps 8 through 1).

10.12Gas Solenoid Valve P/N 122120

The gas solenoid valves must be removed as an assembly along with the regulators, using the following procedures:

1.Turn off the gas supply and power to the steamer.

2.Disconnect wires from the main gas (Section 10.11) and from the gas solenoid valves.

3.From the front of the steamer, loosen and disconnect the pipe union which connects the assembly to the main gas valve.

4.From the left side (or back) of the steamer, use a wrench to loosen and disconnect the aluminum tubing to the inner and outer manifolds.

5.The entire assembly of both regulators and the gas solenoid valves for the upper and lower steam generators may be removed as an integrated unit.

6.Remove the gas solenoid valve(s) as required.

To Reinstall:

7.Clean pipe threads and apply compound to all joints being connected.

8.Install the new gas solenoid valve.

9.Slide the assembly into the steamer and reconnect the pipe union. Align the gas valves with their respective aluminum tubing.

10.Using a wrench, connect the aluminum tubing to the burner manifold.

11.Reconnect the wires to the correct valve.

10.13Igniter Module P/N 122180

1.Shut off power and gas to the steamer.

2.Remove the cover to the electrical compartment.

3.The igniter module is located under the relays.

4.Note or tag the wires for reinstallation if necessary, before unplugging. Carefully disconnect the push

REAR VIEW

26 OM/SM-HY-6G(CE)

Page 25 Page 27
Image 26
Page 25 Page 27
Contents HY-6GCE Hypersteam Atmospheric Convection Important Read First Important Table of Contents ReferencesEquipment Description Inspection and UnpackingWater Conditioning Bpst Connection on the right rear side of the steamerElectrical Supply Connection Installation, Start-Up and ConversionGeneral Gas Supply ConnectionG20 Natural Gas G31 Propane Gas MBar Inch W.C 26.25 10.5 Natural Gas Propane GasMBar In. W.C 10.5 in. W.C Natural Gas Propane Gas Injector No.Drain Connection Initial Start-UpAutomatic Operation of Pilot Operation Gas Lockout Indicator and Reset ControlOperating Procedure ControlsOM/SM-HY-6GCE Suggested Tools CleaningProcedure Outside of Steamer 12 OM/SM-HY-6GCEIf the Service light stays on Steam Generator and Cooking Chamber14 OM/SM-HY-6GCE MaintenanceTroubleshooting Key Description Parts ListExternal Cabinet and Sheet Metal Cavity Control Section 16 OM/SM-HY-6GCESteamer Base Section Front Steamer Base Rear 18 OM/SM-HY-6GCESteamer Plumbing Steamer Motor and Controls 20 OM/SM-HY-6GCESteamer Generator Individual Parts Key Description NewSteamer Individual Parts 22 OM/SM-HY-6GCETop Right Side Panel Louvered Removal P/N Service ProceduresAdjustable Legs P/N Left Side Removal P/NWater Inlet Valve Coil To TestWater Inlet Valve Three Way P/N Drain Box Spray Nozzle P/NSteam Generator To InstallMain Gas Valve and Gas Pressure Adjustment P/N Steam Generator Probes High and Low Water P/NGas Solenoid Valve P/N To ReinstallTo Assemble Igniter Module P/NInstallation Pilot Switch SW3 Removal P/NTo replace the switch Pilot Flame Current CheckTo Reassemble Timer Assembly Timer Fastener NutSteam Generator Gas Jet Manifolds P/N 123704 28 OM/SM-HY-6GCETo Install New Capacitor Fan Motor Assembly Motor Insulation Motor Shaft SealTo Install a New Motor 10.18 FanCavity Steam Hose Assemblies P/N 099953 Top Door Removal/Installation/Alignment P/NSteam Port Gasket 30 OM/SM-HY-6GCETo Align Door Switch P/NDoor Reversing Procedures Door Spring P/N Door Handle, Magnet and Block AssemblyDoor Gasket P/N 32 OM/SM-HY-6GCEDoor Locking Pin P/N Lock Nut P/N Electrical Schematic 34 OM/SM-HY-6GCEService Log Limited Warranty To Commercial Purchasers 36 OM/SM-HY-6GCEPart Number 128805, REV. C 4/06

HY-6G(CE) specifications

Unified Brands HY-6G(CE) is a pioneering cooking solution in the commercial kitchen landscape, known for its exceptional performance, versatility, and cutting-edge technologies. Designed to meet the rigorous demands of foodservice establishments, the HY-6G(CE) excels at efficiently preparing a wide range of dishes while ensuring consistent quality and safety.

One of the standout features of the HY-6G(CE) is its powerful heating capability. Equipped with advanced infrared heating technology, this unit delivers rapid and uniform heat distribution, making it ideal for both quick service and high-volume operations. The adjustable temperature controls allow chefs to fine-tune the cooking process, ensuring that every dish meets their exacting standards.

Another innovative aspect of the HY-6G(CE) is its energy efficiency. The incorporation of smart energy management systems ensures optimal power usage, reducing operational costs without sacrificing performance. The unit’s environmentally friendly design also aligns with sustainability initiatives, making it a responsible choice for modern kitchens.

The HY-6G(CE) boasts a user-friendly interface that facilitates ease of operation. Its digital display provides real-time feedback on cooking parameters, while programmable settings enable chefs to recall precise cooking profiles for various menu items. This feature not only streamlines kitchen workflow but also enhances productivity, allowing staff to focus on delivering exceptional customer service.

Durability is another hallmark of the HY-6G(CE). Constructed from high-quality stainless steel, it withstands the rigors of daily use in busy kitchens while resisting corrosion and wear. Its compact design allows for easy integration into existing kitchen layouts, making it an excellent option for both new builds and remodels.

Safety is paramount in any culinary environment, and the HY-6G(CE) addresses this with multiple safety features. These include automatic shut-off mechanisms and thermal protection systems that safeguard against overheating, ensuring secure operation even in the most demanding settings.

In summary, Unified Brands HY-6G(CE) stands out in the commercial cooking equipment market due to its blend of power, efficiency, and safety. With features that cater to the diverse needs of any foodservice establishment, it is an invaluable tool for chefs looking to elevate their culinary offerings while maintaining operational excellence. Whether in a bustling restaurant or a catering operation, the HY-6G(CE) is designed to deliver reliable and outstanding results.
Top Page Image Contents