Unified Brands HY-6G(CE) service manual Cleaning, Suggested Tools, Procedure Outside of Steamer

Page 12

6.0 - Cleaning

To keep your HY-6E Steamer in proper working condition/order, use the following procedure to clean the unit. This regular cleaning will reduce the effort required to clean the steam generators and cavities.

6.1 Suggested Tools

1.Mild detergent

2.Stainless steel exterior cleaner such as Zepper®

3.Steam generator de-liming agent, such as Groen Delimer Descaler, Lime-Away® or an equivalent. A liquid de-liming agent will be easier to use than crystals or powders. See the warning about chlorides, below

4.De-greaser, such as EncompasS®, Malone 34®, Puritan Puribrute®, or Con-Lie®

5.Cloth or sponge

6.Plastic wool or a brush with soft bristles

7.Spray bottle

8.Measuring cup

9.Nylon pad

10.Towels

11.Plastic disposable gloves

12.Funnel

6.2 Procedure

6.2.1Outside of Steamer

1.Prepare a warm solution of the mild detergent as instructed by the supplier. Wet a cloth with this solution and wring it out. Use the moist cloth to clean the outside of the unit. Do not allow freely running liquid to touch the controls, the control panel, any electrical part, or any open louver.

2.To remove material which may be stuck to the unit, use plastic wool, a fiber brush, or a plastic or rubber scraper with a detergent solution.

3.Stainless steel surfaces may be polished

with a recognized stainless steel cleaner such as Zepper®.

WARNING

DISCONNECT THE POWER SUPPLY BEFORE CLEANING THE OUTSIDE OF THE STEAMER.

KEEP WATER AND CLEANING SOLUTIONS OUT OF CONTROLS AND ELECTRICAL COMPONENTS. NEVER HOSE OR STEAM CLEAN ANY PART OF THE UNIT.

DON’T MIX DE-LIMING AGENTS (ACID) WITH DE-GREASERS (ALKALI) ANYWHERE IN THE UNIT

AVOID CONTACT WITH ANY CLEANERS, DE-LIMING AGENT OR DE- GREASER AS RECOMMENDED BY THE SUPPLIER. MANY ARE HARMFUL. READ THE WARNINGS AND FOLLOW THE DIRECTIONS!

EVEN WHEN THE UNIT HAS BEEN SHUT OFF, DON’T PUT HANDS OR TOOLS INTO THE COOKING CHAMBER UNTIL THE FAN HAS STOPPED TURNING.

DON’T OPERATE THE UNIT UNLESS THE TWO REMOVABLE INTERIOR PARTITIONS HAVE BEEN PUT BACK IN THEIR PROPER LOCATIONS.

DON’T USE ANY CLEANING OR DE- LIMING AGENT THAT CONTAINS ANY SULFAMIC AGENT OR ANY CHLORIDE, INCLUDING HYDROCHLORIC ACID (HCl). TO CHECK FOR CHLORIDE CONTENT SEE ANY MATERIAL SAFETY DATA SHEETS PROVIDED BY THE CLEANING AGENT MANUFACTURER.

IMPORTANT

DO NOT USE ANY METAL MATERIAL (SUCH AS METAL SPONGES) OR METAL IMPLEMENT (SUCH AS A SPOON, SCRAPER OR WIRE BRUSH) THAT MIGHT SCRATCH THE SURFACE. SCRATCHES MAKE THE SURFACE HARD TO CLEAN AND PROVIDE PLACES FOR BACTERIA TO GROW. DO NOT USE STEEL WOOL, WHICH MAY LEAVE PARTICLES IMBEDDED IN THE SURFACE WHICH COULD EVENTUALLY CAUSE CORROSION AND PITTING.

12 OM/SM-HY-6G(CE)

Page 11 Page 13
Image 12
Page 11 Page 13
Contents HY-6GCE Hypersteam Atmospheric Convection Important Read First Important Table of Contents ReferencesEquipment Description Inspection and UnpackingWater Conditioning Bpst Connection on the right rear side of the steamerInstallation, Start-Up and Conversion GeneralElectrical Supply Connection Gas Supply ConnectionNatural Gas Propane Gas MBar In. W.C 10.5 in. W.CG20 Natural Gas G31 Propane Gas MBar Inch W.C 26.25 10.5 Natural Gas Propane Gas Injector No.Drain Connection Initial Start-UpAutomatic Operation of Pilot Gas Lockout Indicator and Reset Control Operating ProcedureOperation ControlsOM/SM-HY-6GCE Cleaning Procedure Outside of SteamerSuggested Tools 12 OM/SM-HY-6GCEIf the Service light stays on Steam Generator and Cooking ChamberMaintenance Troubleshooting14 OM/SM-HY-6GCE Parts List External Cabinet and Sheet MetalKey Description Cavity Control Section 16 OM/SM-HY-6GCESteamer Base Section Front Steamer Base Rear 18 OM/SM-HY-6GCESteamer Plumbing Steamer Motor and Controls 20 OM/SM-HY-6GCESteamer Generator Individual Parts Key Description NewSteamer Individual Parts 22 OM/SM-HY-6GCEService Procedures Adjustable Legs P/NTop Right Side Panel Louvered Removal P/N Left Side Removal P/NTo Test Water Inlet Valve Three Way P/NWater Inlet Valve Coil Drain Box Spray Nozzle P/NTo Install Main Gas Valve and Gas Pressure Adjustment P/NSteam Generator Steam Generator Probes High and Low Water P/NTo Reinstall To AssembleGas Solenoid Valve P/N Igniter Module P/NPilot Switch SW3 Removal P/N To replace the switchInstallation Pilot Flame Current CheckTimer Assembly Timer Fastener Nut Steam Generator Gas Jet Manifolds P/N 123704To Reassemble 28 OM/SM-HY-6GCEFan Motor Assembly Motor Insulation Motor Shaft Seal To Install a New MotorTo Install New Capacitor 10.18 FanDoor Removal/Installation/Alignment P/N Steam Port GasketCavity Steam Hose Assemblies P/N 099953 Top 30 OM/SM-HY-6GCEDoor Switch P/N Door Reversing ProceduresTo Align Door Handle, Magnet and Block Assembly Door Gasket P/NDoor Spring P/N 32 OM/SM-HY-6GCEDoor Locking Pin P/N Lock Nut P/N Electrical Schematic 34 OM/SM-HY-6GCEService Log Limited Warranty To Commercial Purchasers 36 OM/SM-HY-6GCEPart Number 128805, REV. C 4/06

HY-6G(CE) specifications

Unified Brands HY-6G(CE) is a pioneering cooking solution in the commercial kitchen landscape, known for its exceptional performance, versatility, and cutting-edge technologies. Designed to meet the rigorous demands of foodservice establishments, the HY-6G(CE) excels at efficiently preparing a wide range of dishes while ensuring consistent quality and safety.

One of the standout features of the HY-6G(CE) is its powerful heating capability. Equipped with advanced infrared heating technology, this unit delivers rapid and uniform heat distribution, making it ideal for both quick service and high-volume operations. The adjustable temperature controls allow chefs to fine-tune the cooking process, ensuring that every dish meets their exacting standards.

Another innovative aspect of the HY-6G(CE) is its energy efficiency. The incorporation of smart energy management systems ensures optimal power usage, reducing operational costs without sacrificing performance. The unit’s environmentally friendly design also aligns with sustainability initiatives, making it a responsible choice for modern kitchens.

The HY-6G(CE) boasts a user-friendly interface that facilitates ease of operation. Its digital display provides real-time feedback on cooking parameters, while programmable settings enable chefs to recall precise cooking profiles for various menu items. This feature not only streamlines kitchen workflow but also enhances productivity, allowing staff to focus on delivering exceptional customer service.

Durability is another hallmark of the HY-6G(CE). Constructed from high-quality stainless steel, it withstands the rigors of daily use in busy kitchens while resisting corrosion and wear. Its compact design allows for easy integration into existing kitchen layouts, making it an excellent option for both new builds and remodels.

Safety is paramount in any culinary environment, and the HY-6G(CE) addresses this with multiple safety features. These include automatic shut-off mechanisms and thermal protection systems that safeguard against overheating, ensuring secure operation even in the most demanding settings.

In summary, Unified Brands HY-6G(CE) stands out in the commercial cooking equipment market due to its blend of power, efficiency, and safety. With features that cater to the diverse needs of any foodservice establishment, it is an invaluable tool for chefs looking to elevate their culinary offerings while maintaining operational excellence. Whether in a bustling restaurant or a catering operation, the HY-6G(CE) is designed to deliver reliable and outstanding results.
Top Page Image Contents