Smeg SCP108SG Instructions for the Installer, Installing The Appliance, Electrical connection

Page 27

Instructions for the Installer

Instructions for the Installer

12.INSTALLING THE APPLIANCE

12.1Electrical connection

The nameplate with the technical data, serial number and mark is in a visible position on the oven door frame.

The nameplate must never be removed.

The appliance must be connected to earth in compliance with electrical system safety regulations.

If a permanent connection is used, the appliance's power supply line must be fitted with an omnipolar breaking device with contact gap of at least 3 mm, located in an easily accessible position close to the appliance itself.

If a socket and plug connection is used, check that they are of the same type. Do not use reducers, adapters or junctions since they may cause overheating or burns.

Operation at 220-240 V~: use a

type H05RR-F (3 x 1.5 mm2) or

type H05V2V2-F (3 x 1.5 mm2) three-wire cable.

The earth wire (yellow-green) must be at least 20 mm longer than the other wires at the end for connection to the appliance.

If the power supply lead has to be replaced, remove the rear casing by undoing the screws as shown below. The power lead gauge must be at

least 1.5 mm2 (3 X 1.5 cable) and it must withstand temperatures up to 90°C (H05V2V2-F). Make sure that the cables follow the best possible route and use band clamps to fix them at the side of the cabinet, to avoid any contact with the oven.

57

Image 27

Contents Table of Contents 1. PRECAUTIONS FOR USE Precautions for Use2. DISPOSAL INSTRUCTIONS - OUR ENVIRONMENT POLICY Disposal instructions3. SAFETY PRECAUTIONS Safety precautions5. BEFORE INSTALLATION Instructions for the User4. GET TO KNOW YOUR OVEN DISPLAY 6. DESCRIPTION OF FRONT PANEL CONTROLSTHERMOSTAT-TIMER KNOB for convenience it will be referred to as PT1From now on, for convenience it will be referred to as PT2 FUNCTION-SWITCH ON KNOBAll cooking operations must be carried out with the door closed 7. USING THE OVEN7.1 Precautions and General Advice 7.2 Operating modes7.4.1 Cooking with preset temperature 7.5 Programmed cooking procedures7.3 First use 7.4 Selecting the function7.5.2 Semiautomatic cooking To switch the oven off completely, turn PT2 to the 0 symbolTurn PT2 to the 0 symbol to switch the oven off completely Modifying the data set7.5.3 Automatic cooking Turn PT2 to 0 to switch off the oven7.6 Secondary menu Turn 7.6.1 Modifying the secondary menu settingsMENU MODIFICATION PROCEDURE SYMBOLS7.8 Inside light 7.7 Cooling fan systemOptional accessories 8. ACCESSORIES AVAILABLEPASTA 9. RECOMMENDED COOKING TABLESCONVENTIONAL COOKING The oven must be preheated before all cooking operationsPROVING - DEFROSTING HOT AIR COOKINGGRILLING ROTISSERIE COOKINGRUNNER POSITION FROM Never use a jet of steam for cleaning the inside of the oven 10. CLEANING AND MAINTENANCE10.1 Cleaning stainless steel 10.2 Routine daily cleaning10.4 Cleaning the oven 10.5 Cleaning the door glazingRemove all removable parts 135 MIN 10.6 Pyrolysis automatic oven cleaning10.6.1 Before starting the automatic cleaning cycle 90 MIN10.6.2 How the automatic cleaning cycle works 10.6.3 Setting the cleaning cycle 11. EXTRAORDINARY MAINTENANCE 11.1 Changing the light bulbUse only light bulbs approved for ovens T 500C 11.2 Removing the door 11.2.1 With type 1 mobile levers11.3 Removing the gasket 11.4 Removing the inside glass with the door cold 12.1 Electrical connection Instructions for the Installer12. INSTALLING THE APPLIANCE type H05V2V2-F 3 x 1.5 mm2 three-wire cable12.2 Positioning the oven