Anritsu S113C, S332C, S114C, S331C manual RUN/HOLD button

Page 28

Chapter 2 Functions and Operations

SWEEP

Displays the Sweep function soft key menu for the current operating mode.

Sweep Menu Provides for changing the display resolution, single or continuous sweep, and access to the Trace Math functions.

Choosing SWEEP in FREQ or DTF measurement modes causes the soft keys below to be displayed.

￿RESOLUTION — Opens the display to change the resolution. Choose 130, 259, or 517 data points. (In DTF mode, resolution can be adjusted through the DTF-AID table.)

￿SINGLE SWEEP — Toggles the sweep between single sweep and continu- ous sweep. In single sweep mode, each sweep must be activated by the

RUN/HOLD button.

￿TRACE MATH — Opens up the Trace Math functions (trace-memory or trace+memory) for comparison of the real time trace in the display with any of the traces from memory. (Not available in DTF mode.)

￿TRACE OVERLAY — Opens up the Trace Overlay functions menu to allow the current trace to be displayed with a trace in memory overlaid on it. Choose ON or OFF and SELECT TRACE to select the trace from memory to be overlaid.

Choosing SWEEP in SPECTRUM ANALYZER mode causes the soft keys below to be displayed.

￿RBW — Sets the resolution bandwidth so that it is either coupled automati- cally to the span (AUTO) or manually adjustable (MANUAL).

￿VBW — Sets the video bandwidth so that it is either coupled automatically to the span (AUTO) or manually adjustable (MANUAL).

￿MAX HOLD — Displays and holds the maximum responses of the input sig- nal.

￿CONT/SINGLE — Toggles between continuous and single sweep.

￿MEASURE — Activates a menu of measurement related functions. Use the corresponding softkey to select the measurement function.

￿FIELD STRENGTH — Accesses a menu of field strength measurement options.

ON/OFF - Turns field strength measurements on or off.

SELECT ANTENNA - Selects an antenna profile to be used for field strength measurements.

BACK - Returns to the previous menu.

￿OBW — Activates the occupied bandwidth menu. Select either METHOD, % or dBc method of occupied bandwidth measurement. METHOD allows selection of either % of power or dB Down. Selecting % allows entry of the desired % of occupied bandwidth to be measured.

Selecting dBc allows entry of the desired power level (dBc) to be mea- sured.

￿DETECTION — Accesses a menu of detector modes including POSI- TIVE PEAK detection, AVERAGE detection and NEGATIVE PEAK detection.

2-13

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Users Guide Warranty Page Table of Contents Power Measurement Iii/iv Page Standard Accessories Chapter General InformationIntroduction DescriptionOptional Accessories OptionsPerformance Specifications Description Site Master Spectrum Analyzer Preventive Maintenance CalibrationAnnual Verification InstaCal ModuleAnritsu Service Centers Test Connector Panel Chapter Functions and OperationsFront Panel Overview Active Function Block Soft KeysFunction Hard Keys ModeKeypad Hard Keys ClearAuto Soft Keys MODE=FREQ FREQ/DIST SoftkeysMODE=DTF FREQ/DIST Softkeys MODE=SPECTRUM Analyzer FREQ/DIST Amplitude Softkeys Power Monitor Mode Soft Key Labels Functions and Operations Functions and Operations Amplitude RUN/HOLD button Functions and Operations Power Monitor Menu Functions and Operations Limit SYS Symbols Error CodesSelf Test Errors Self TestError Message Range Errors ERRORD2InstaCal Error Messages InstalledError MessageDescription Battery Information Charging a New BatteryCharging the Battery in the Site Master Charging the Battery in the Optional ChargerBattery Charge Indicator Battery LifeImportant Battery Information Power On Procedure Chapter Getting StartedSelect the Frequency or Distance CalibrationTrace Characteristics in Return Loss Mode Calibration VerificationManual Calibration Procedure CalibrationTermination Method InstaCal Module VerificationOffset Method InstaCal Module Calibration Procedure Calibration with the Test Port Extension CableSetting the Scale Save and Recall a SetupSaving a Setup Auto ScaleRecalling a Setup Save and Recall a DisplaySaving a Display Recalling a DisplayChanging the Units Set the Distance and Cable TypeChanging the Display Language Printing Printing a ScreenPrinter Switch Settings PrinterUsing the Soft Carrying Case Using the Site Master Soft Carrying CaseChapter Cable & Antenna Measurements Line Sweep FundamentalsInformation Required for a Line Sweep Cable & Antenna MeasurementsTypical Line Sweep Test Procedures System Return Loss MeasurementProcedure Cable Loss Mode Insertion Loss MeasurementSet M1 to Marker to Peak Set M2 to Marker to Valley Procedure Return Loss Mode Typical Transmission Line Cable Loss TraceTypical Return Loss Trace Distance-To-Fault DTF Transmission Line Test Procedure DTF-SWR Mode Shows an example of a typical DTF return loss traceAntenna Subsystem Return Loss Test 11/4-12 Page Chapter Spectrum Analyzer Measurements Occupied BandwidthChannel Power Measurement Channel Power Measurement with the Site MasterProcedure Adjacent Channel Power Measurement Example Acpr SpecificationCW Wave Out-of-Band Spurious Emission Measurements In-Band/Out-of-Channel Measurements Field Strength Measurement Antenna Calculations VdBV PdBmPage Chapter Power Measurement Power MeasurementDisplaying Relative Power Chapter Site Master Software Tools FeaturesSystem Requirements Installation Communication Port SettingInterface Cable Installation Using Software ToolsDownloading Traces from the Site Master Display Mode Plot CapturePlot Properties Graph TitlesTrace Overlay or Plot Overlay Saving TracesMarkers MiscSaving a Plot to a Spreadsheet Custom Cable ListCreating a Custom Cable List Uploading a Cable List Entering Antenna FactorsQuerying the Site Master Cable List Creating a Database Uploading Antenna FactorsPrinting Formats Coaxial Cable Technical Data Appendix a Reference DataAppendix a Reference Data A-4 Page Introduction Appendix B WindowingExamples Appendix B Windowing B-4 Page

S113C, S332C, S114C, S331C specifications

Anritsu, a leader in test and measurement solutions, offers a range of handheld tools that cater to the needs of professionals in the RF and microwave industries. Among these tools are the Anritsu S331C, S114C, S332C, and S113C, each designed with unique features and technologies that make them suitable for various applications.

The Anritsu S331C is a Cable and Antenna Analyzer that is particularly valued for its accuracy and ease of use. It operates within a frequency range of 3 MHz to 4 GHz, making it applicable for both wireless and microwave communication systems. One of its standout features is the built-in Time Domain Reflectometry (TDR) function, which allows technicians to pinpoint faults in cables quickly. The S331C's intuitive touch-screen interface ensures seamless operation, while its lightweight design allows for portability in the field.

On the other hand, the Anritsu S114C is a versatile handheld RF power meter that can measure a wide range of power levels and frequencies. Its exceptional measurement accuracy and broad dynamic range make it suitable for various applications, from network testing to maintenance. It supports both peak and average power measurements, providing users with the flexibility to adapt to different testing scenarios. The S114C also features a memory function that allows users to store and recall measurement data easily.

The S332C model is designed for more advanced applications, offering vector network analysis capabilities. Operating within a frequency range of 5 kHz to 4 GHz, it is used for characterizing components such as filters, amplifiers, and cables. The S332C features a high-resolution display and supports automated measurements, making it a powerful tool for engineers involved in the design and validation of RF components.

Lastly, the Anritsu S113C is an excellent choice for professionals requiring a compact and efficient solution for insertion loss and return loss measurements. This analyzer covers a frequency range of 5 kHz to 4 GHz and is especially suited for testing antennas and RF components. The S113C's lightweight design, combined with its user-friendly interface, allows operators to conduct measurements easily in various environments, ensuring high performance and reliability.

In summary, the Anritsu S331C, S114C, S332C, and S113C represent a comprehensive suite of handheld analyzers that cater to diverse needs in the RF and microwave sectors. With features like TDR function, RF power measurements, vector network analysis, and a focus on portability, these instruments are essential tools for professionals looking to enhance their testing capabilities and ensure high-quality network performance.
Top Page Image Contents