XtremeMac Room Audio System user manual Setting the Alarms, Setting the Date and Time Format

12 LUNA™ User Manual

4.Turn the Right Control Knob to highlight either “Contrast” or “Dimmer” and push to select. The level will blink to indicate that it can be adjusted.

5.Turn the Right Control Knob to increase/decrease the level for contrast (from 0 to 60) and for the dimmer (from 0 to 20) push to accept and save your changes. If you set the dimmer to a level lower than 5, touching any control will automatically bring the dimmer up to a level 5 for a few moments so that you can make adjustments to your settings.

Note: You may also invert the display colors through the “Display Options” menu.

SHORTCUT

You may turn the Right Control Knob to increase/ decrease the brightness of the display at any time, except when in menu or sleep mode.

Setting the Date and Time Format:

Luna’s default date format is Month, Day, Year (MM.DD.YY) and default time format is a 12-hour clock. To select Day, month, year (DD.MM.YY) and/or to select a 24-hour clock format, follow these instructions:

1.Push the Right Control Knob to access the main menu. The menu will appear on Luna’s display.

2.Turn the Right Control Knob until the “Settings” menu item is highlighted and push to select.

3.Turn the Right Control Knob until the “Format” menu item is highlighted and push to select.

4.Turn the Right Control Knob to highlight either “Time Format” or “Date Format” and push to select.

5.Turn the Right Control Knob to highlight your preferred format and push to select. This will automatically turn the selected format to “ON” the other format to “OFF”.

Setting the Daylight Savings Time Option:

1.Push the Right Control Knob to access the main menu. The menu will appear on Luna’s display.

2.Turn the Right Control Knob until the “Settings” menu item is highlighted and push to select.

3.Turn the Right Control Knob until the “DST” menu item is highlighted and push to toggle between “OFF” and “ON”. Activate this feature when Day Light Savings Time is in effect. This will advance the time one hour.

Setting the Alarms

Luna’s two alarms work independently from each other, allowing you to customize each one to your preference. You can set the time, wake to source, volume/volume ramping, dimmer brightness and even snooze time for each.

Setting Alarm Time:

1.Push the Right Control Knob to access the main menu. The menu will appear on Luna’s display.

2.Turn the Right Control Knob to highlight either “Alarm 1” or “Alarm 2” and push to select.

3.Push the Right Control Knob again and the hour will blink to indicate it can be adjusted. Turn the Right Control Knob to change the hour, AM or PM (indicated by an “A” or a “P” next to the time) and push to accept the correct hour and advance to adjust the minutes.

LUNA™ User Manual 13

4.The minute section will then blink to indicate it can be adjusted. Turn the Right Control Knob to change the minutes and push to accept and save your changes.

5.Once you set the alarm time(s), you need to make sure to activate the alarm(s). Push the Alarm 1 Button on the back left to activate Alarm 1 and/or push the Alarm 2 Button on the back right to activate Alarm 2.

The display will show each alarm time and source icon when the alarm is activated.

SHORTCUT

You may also access Alarm 1 and Alarm 2 menus by

holding down the corresponding Alarm Button.

Setting Alarm Source:

1.Push the Right Control Knob to access the main menu. The menu will appear on Luna’s display.

2.Turn the Right Control Knob to highlight either “Alarm 1” or “Alarm 2” and push to select.

3.Turn the Right Control Knob until the “Wake To” menu item is highlighted and push to select. Turn the Right Control Knob to choose between “iPod”, “Radio”, or “Sounds”. Highlight your source choice and push to accept.

Waking to iPod

–If “iPod” is selected as alarm source, be sure to properly dock your iPod in the Universal dock well. If you do not dock your iPod, the alarm source will default to the buzzer to make sure that you do not miss your set alarm time.

–Set your iPod to shuffe or pick the song or playlist you would like to wake to.

Note: Ensure your playlist has an adequate amount of songs to play for the amount of time it will take you to wake.

Waking to radio

–If “Radio” is selected as alarm source, make sure the FM and AM antennas are connected per the instructions.

–Next, you may select a preset station or tune Luna to your preferred AM or FM station (see “Set Presets”).

–To select a preset station, select radio as alarm source (see step 2 above). Push the Right Control Knob to select the “Presets” menu item and push to select. The band and station will blink. Turn the Right Control Knob to toggle through your preset stations. Push to select desired preset station.

–To manually tune the radio, turn the Right Control Knob until

the “Tune” menu item is highlighted. Push to select. The AM/FM band will blink to indicate that it can be adjusted. Turn the Right Control Knob to the desired band and push to accept the band and advance to tune the frequency. The frequency will then blink to indicate it can be adjusted. Turn the Right Control Knob to tune the desired frequency and push to accept.

Note: For best FM reception, the antenna should be extended fully and vertically above Luna. For best AM reception, the AM loop antenna should be positioned away from Luna.