Broan K7388 manual Install Mounting Bracket, Install Flue Mounting Bracket, Ducted and NON-DUCTED

Page 7

INSTALL MOUNTING

BRACKET

1.Construct wood wall framing that is flush with interior surface of wall studs.

Make sure:

a)the framing is centered over installation location.

b)the height of the framing will allow the mounting bracket to be secured to the framing within the dimensions shown.

2.After wall surface is finished, secure mounting bracket to framing using dimen- sions shown.

FRAMING BEHIND DRYWALL

36-

 

 

 

 

13/16”

to

42-

 

above

 

11/16”

 

cooktop

36-13/16"= bottom of hood 24" above cooktop

42-11/16"= bottom of hood 30" above cooktop

INSTALL FLUE MOUNTING BRACKET

DUCTED AND NON-DUCTED

1.Assemble the flue mounting bracket, adjusting outside width as shown. Fig.4

2.Carefully center the mounting bracket directly over the range hood location.

3.Secure the bracket assembly to the ceiling using (2) 4.8x38mm mounting screws and drywall anchors. Make sure the bracket is pushed into the corner, tight against the wall and centered over the hood.

FLUE MOUNTING

3.9 x 6 mm

 

BRACKET

 

 

FLAT HEAD

 

BRACKET SCREWS

 

10-7/16”

 

 

(265.6 mm)

 

 

 

FIG.

4

- 7 -

Image 7
Contents English Français Español Model K7388Page Intended for Domestic Cooking only ! Warning Read and Save These InstructionsPage Prepare the Hood Wiring Install the DuctworkInstall Flue Mounting Bracket Install Mounting BracketDucted and NON-DUCTED Ducted Configuration NON Ducted Configuration NON Ducted CONFIGURATION, cont’d InstallHood Grease Filters NON-DUCTED Recirculation Filter InstallationMaintenance Hood CleaningControls OperationHeat Sentry Halogen Bulbs Fuse ReplacementWarranty Switch OFF the Electricity SupplyAvertissements Seulement Pour Utilisation Domestique ! AvertissementsPage Preparez LA Hotte Installation Electrique Installation DU Systeme’EVACUATION Installation DU Support DE Fixation DU Carneau Installation Etrier D’ASSEMBLAGECaréné ET NON Caréné Préparation DE LA Hotte Configuration CarénéeConfiguration NON Carénée Préparation DE LA Hotte Configuration NON Carénée suiteDE LA Hotte Entretien Assemblage DU Filtre PourNettoyage de votre hotte Avertissement CommandesFonctionnement Heat Sentrymc’AMPOULE Peut Etre Chaude Remplacement FusibleAmpoules Halogenes GarantieAdvertencia LEA Y Conserve Estas InstruccionesAdvertencia Prepare LA Campana Instalacion Electrica Instalacion DEL Tubo DE ExtraccionCON Conducto Y SIN Conducto Instalacion Soporte Para EL MontajePreparación DE LA Campana Configuración CON ConductoMonte el pleno de recirculación al conducto flexible. Fig Configuración SIN ConductoInstalación DE Configuración SIN CONDUCTO, continuaciónLA Campana Filtros antigrasa Filtro al carbón configuración sin tuboInstalacion DEL Filtro MantenimientoAvertencia FuncionamientoMandos Heat SentrymrAtención LAS Lámparas Pueden Estar Calientes Lamparas HalogenasSustitucion Fusible GarantiaModel K7388 Heat Sentry Service PartsKeyno Description Modele K7388 Heat Sentry Liste Pieces DE RechangePart N Description Modelo K7388 Heat Sentry Lista DE Piezas DE RecambioCÓD. N Pieza N Descripción Model K7388 Heat Sentry 04307117/3