GAS Line Installation

This appliance may be installed in an aftermarket permanently located, manufactured (mobile) home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless an avail- able certified kit is used.

When purging gas line one of the glass sides must be removed.

The gas pipeline can be brought in through the rear right side (see Fireplace Specifications) of the appliance as well as the bottom. Knockouts are provided at convenient locations to allow for the gas pipe installation and testing of any gas connection. It is most convenient to bring the gas line in from the rear right side, as this allows fan installation or removal without disconnecting the gas line.

The gas line connection can be made with properly tinned 3/8" copper tubing, 3/8" rigid pipe or an approved flex connector. Since some municipalities have some additional local codes, it is always best to consult your local authority and the CAN/ CGA-B149 (1. or .2) Installation code or for U.S.A Installations consult the current National Fuel Gas Code, ANSI Z223.1

Always check for gas leaks with a mild soap and water solution. Do not use an open flame for leak testing.

The gas control is equipped with a captured screw type pressure test point, therefore it is not necessary to provide a 1/8" test point up stream of the control.

1/2" GAS SUPPLY

1/2" X 3/8" REDUCER

3/8" NIPPLE

3/8" X 3/8" SHUT OFF VALVE
	3/8" NIPPLE
	3/8" UNION
Typical gas supply installation	3/8" NIPPLE

Fig..5

When using copper or flex connector use only approved fittings. When using black iron pipe always provide a union so that gas line can be easily disconnected for burner or fan servicing. See Fig. 5. See gas specification for pressure details and ratings.

The fireplace valve must not be subjected to any test pressures exceeding 1/2 psi. Isolate or disconnect this or any other gas appliance control from the gas line when pressure testing.

- 6 -

REMOTE SWITCH INSTALLATION

1.Thread wire through the electrical knockout located on rear of fireplace. Do not cut wire or insulation on metal edges. Ensure that wire is protected. Run the other end to a conveniently located wall receptacle box.

2.Attach wire to switch and install switch into receptacle box. Attach cover plate to switch.

3.Connect wiring to gas valve. (Fig. 6)

	VALVE
THERMOPILE	TPTH
	TP
	TH
			P
		I
		TOL
ON/OFF SWITCH OR		Fig.6
MILLIVOLT THERMOSTAT		Fig.6
MILLIVOLT THERMOSTAT

ALTERNATE SWITCH LOCATION:

Remote switch can be installed on the front side of the access door. Simply mount the switch to the switch bracket provided. Screw the bracket on either side of the frame, lining up the screws with the pre-punched holes. (Fig. 7)

Fig. 7

DO NOT WIRE MILLIVOLT REMOTE WALL SWITCH FOR GAS FIREPLACE TO A 120V POWER SUPPLY.

FOR LIGHTING INSTRUCTIONS PLEASE TURN TO PAGE 30.

DVRSL, DVRSR, DVRS3 specifications

Vermont Castings has been a trusted name in the manufacturing of high-quality wood and gas stoves and fireplaces for decades. Among their extensive lineup of gas-burning appliances, the DVRS3, DVRSR, and DVRSL models stand out for their impressive combination of efficiency, aesthetic appeal, and user-friendly features. These models exemplify Vermont Castings' commitment to craftsmanship, innovation, and environmental responsibility.

The DVRS3 is a powerful direct vent gas stove that offers cozy warmth to any living space. It features a large firebox capable of accommodating different log options and provides a maximum input of up to 30,000 BTUs. One key feature of the DVRS3 is its advanced heat exchange system, which enhances heat distribution and efficiency, ensuring that more of the heat generated is released into the room rather than lost through the chimney. Additionally, the stove is designed with a full-width cast iron door and large ceramic glass window, providing an unobstructed view of the flames for a captivating ambiance.

The DVRSR model brings similar qualities but with a more contemporary design. This direct vent stove is engineered to fit seamlessly into modern homes while delivering efficient heating. With a maximum output of up to 25,000 BTUs, it maintains an eco-friendly approach, having been certified for low emissions. The DVRSR also comes equipped with various customization options, including different finishes and decorative options, allowing homeowners to match their stove with their interior design.

For those looking for a space-saving alternative without sacrificing performance, the DVRSL model is ideal. This slim-profile direct vent gas stove is designed to fit in tighter spaces while still offering impressive heating capabilities. With a maximum BTU output of 30,000, the DVRSL is packed with features such as an easy-to-use electronic ignition and remote control capability, allowing users to adjust the flame height and temperature settings with ease.

Each of these models is equipped with Vermont Castings' signature technology that promotes safety, efficiency, and reliability. From built-in safety shut-off systems to durable materials that withstand the test of time, the DVRS3, DVRSR, and DVRSL models are designed to provide years of dependable service. Whether you value traditional aesthetics or modern design, Vermont Castings has engineered these gas stoves to meet the diverse needs of today’s homeowners, combining style, functionality, and peace of mind in each product.