Sherwood R-904 manual UsInG FUnctIons oF ReMote contRoL, Entering a setup code

Page 15

R-904(G)_ENG_091014:R-904(G) 2009-11-11 오후 12:05 페이지 15

UsInG FUnctIons oF ReMote contRoL

This remote control can control up to 8 different components.

Before operating audio and video components other than this receiver with using this remote control, the setup code for each component should be entered.

For system remote control operation, “000” was stored previously in the memory of the device button “DOCK” for Sherwood iPod dock, “CD” for Sherwood CD player, “BD” for Sherwood BD/DVD player and “TV” for Sherwood TV respectively as its factory setup code. So, you don’t need to enter its code for each Sherwood component except in such a case that its code does not work.

ENGLISH

Entering a setup code

1. Turn on the component you want to operate.

2. Find the setup codes according to the type and the brand name of your component, referring to “Setup Code Table” on page 44.

3. Press and hold down both the ENTER button and the desired one of the DEVICE buttons for more than 1 seconds.

• The LED will flicker once.

Note :

The “AVR” button is unavailable for the audio components other than this receiver.

4. Enter a 3 digit code, aiming the remote control at the remote sensor on the component.

Example: When entering “001”.

If entering is performed successfully, the LED will flicker twice.

To be sure that the setup code is correct, press the POWER ON (or STANDBY) button. If your component is turned off, the setup code is correct.

When your component is not turned off, repeat the above steps 2 to 4, trying each code for your component until you find one that works.

Notes:

If the LED did not flicker twice, then repeat the above steps 3 to 4 and try entering the same code again.

Manufacturers may use different setup codes for the same product category. For that reason, it is important that you check to see if the code you have entered operates as many controls as possible. If only a few functions operate, check to see if another code will work with more buttons.

5. Repeat the above steps 1 to 4 for each of your

components.

15

Image 15
Contents 904 Read this Before Operating Your Unit IntroductionContents System Connections Connecting Audio COmPONENTConnecting Video COmPONENTS Copyright protection system HDmI High Definition multimedia Interface connection *1Connecting speaker wire Connecting SPEAkERSConnecting ROOm2 SPEAkERS Speaker placementConnecting for SYSTEm Control Fluorescent Display Front Panel ControlsFront AUx JACk Setup mIC JACkMACROM1~M3 buttons Universal Remote ControlsSound Parameter button Numeric 0~9, +10 Sleep button Input Selector buttonsStop Function Table of the Numbered ButtonsOPeRAtInG coMPonentsWItH ReMote contRoL LoADInG BAtteRIes ReMote contRoL oPeRAtIon RAnGeUsInG FUnctIons oF ReMote contRoL Entering a setup codeRepeat the above steps 1 to 4 for each of your Components Using a punch-through function Removing a punch-through functionRemoving all punch-through functions Operating a macro function Programming a macro functionOperations Listening to a PROGRAm SourceBefore operation Select the digital or analog input connected as desired Listening with headphonesAdjust the overall volume Muting the soundSurround modes SURRoUnD soUnDHall StadiumClassic MoviePress the Sound Parameter button When adjusting the sound parametersWhen selecting the EQ Room EQ When selecting the L.SYNC Lip-SyncWhen selecting the Dm Dual mono When selecting the A.DLY Auto Delay When selecting the DRC Dynamic Range ControlWhen selecting the LFE LFE level When selecting the HDmI HDmI Audio Out①. Press the Enter button to enter the Dolby Volume setup Select the desired channel Adjusting the current channel levelAdjust the level of the selected channel as desired Repeat the above steps 1 and 2 to adjust each channel levelPress the Tuning buttons for more than 0.5 second Auto tuningManual tuning Auto presettingPress the Enter button Presetting radio stationsTuning to preset stations TuningWhile displaying SEARCH, select the desired program type FM mode, press the Search Mode buttonListening to RDS BROADCASTSFm only Searching for stations by program typeDisplaying RDS information Adjusting the brightness of the fluorescent display Operating the sleep timerROOm2 Source PLAYBACk Turn on the ROOM2 functionSelect the desired input as a ROOM2 source Turn the setup menu on System SetupSET Rmeq Setup menu flow①. Press the Enter button to enter the tone adjustment mode Setting the SYSTEmPreparations Setting the ROOm EQSetting the SPEAkER Setup About the speaker size When selecting the SPEAkER ConfigurationPress the Enter button to confirm your selection When selecting the Crossover FrequencyWhen selecting the Channel Level To cancel the test tone function, press the Return buttonAbout the speaker distance When selecting the SPEAkER DistanceWhen selecting the ROOm2 volume Setting the mULTI ROOm SetupWhen the ROOm2 mode is set to on When selecting the ROOm2 inputTroubleshooting Guide PROBLEmREmEDY Specifications Setup Code Table Inno HIT DOCK-VCR Otto Verand BD/DVD SAT AUX-USB/MD 904