Sherwood R-904 manual Adjusting the current channel level, Select the desired channel

Page 26

R-904(G)_ENG_091014:R-904(G) 2009-11-11 오후 12:05 페이지 26

Adjusting the current channel level

ENGLISH

•After adjusting each channel level with test tone, adjust the channel levels either according to the program sources or to suit your tastes. (For details, refer to “When selecting the CHANNEL LEVEL” on page 39.)

1.Select the desired channel.

• Each time this button is pressed, the channel is selected as

	follows:
	→ L → C → R			→ SR	→ (SBR → SBL)
	→ L → C → R			→ SR	→ (SBR → SBL)
	Front	Center Front		Surround		Surr. Back		Surr. Back
	Left		Right	Right		Right		Left
			SW	←	SL	←
			SW	←	SL	←
			Subwoofer	Surround Left

( ) : Possible only when the surround back speaker is set to 2ch (“x2”) or 1ch (“x1”)

• When the channel level disappears, press this button again.

• Depending on the speaker settings (“NO”), etc., some channels cannot be selected.

2. Adjust the level of the selected channel as desired.

• The channel levels can be adjusted within the range of -15 ~ +15 dB.

■Note:

• When selecting the VuNow as an input source, you cannot adjust the channel levels.

3. Repeat the above steps 1 and 2 to adjust each channel level.

26

Image 26

Contents 904 Introduction Read this Before Operating Your UnitContents Connecting Audio COmPONENT System ConnectionsConnecting Video COmPONENTS HDmI High Definition multimedia Interface connection *1 Copyright protection systemConnecting SPEAkERS Connecting speaker wireSpeaker placement Connecting ROOm2 SPEAkERSConnecting for SYSTEm Control Front Panel Controls Fluorescent DisplaySetup mIC JACk Front AUx JACkNumeric 0~9, +10 Sleep button Input Selector buttons Universal Remote ControlsSound Parameter button MACROM1~M3 buttonsFunction Table of the Numbered Buttons StopLoADInG BAtteRIes ReMote contRoL oPeRAtIon RAnGe OPeRAtInG coMPonentsWItH ReMote contRoLRepeat the above steps 1 to 4 for each of your Components UsInG FUnctIons oF ReMote contRoLEntering a setup code Removing all punch-through functions Using a punch-through functionRemoving a punch-through function Programming a macro function Operating a macro functionBefore operation OperationsListening to a PROGRAm Source Muting the sound Listening with headphonesAdjust the overall volume Select the digital or analog input connected as desiredSURRoUnD soUnD Surround modesMovie StadiumClassic HallWhen adjusting the sound parameters Press the Sound Parameter buttonWhen selecting the Dm Dual mono When selecting the EQ Room EQWhen selecting the L.SYNC Lip-Sync When selecting the HDmI HDmI Audio Out When selecting the DRC Dynamic Range ControlWhen selecting the LFE LFE level When selecting the A.DLY Auto Delay①. Press the Enter button to enter the Dolby Volume setup Repeat the above steps 1 and 2 to adjust each channel level Adjusting the current channel levelAdjust the level of the selected channel as desired Select the desired channelAuto presetting Auto tuningManual tuning Press the Tuning buttons for more than 0.5 secondTuning Presetting radio stationsTuning to preset stations Press the Enter buttonSearching for stations by program type FM mode, press the Search Mode buttonListening to RDS BROADCASTSFm only While displaying SEARCH, select the desired program typeDisplaying RDS information Operating the sleep timer Adjusting the brightness of the fluorescent displaySelect the desired input as a ROOM2 source ROOm2 Source PLAYBACkTurn on the ROOM2 function System Setup Turn the setup menu onSetup menu flow SET RmeqSetting the SYSTEm ①. Press the Enter button to enter the tone adjustment modeSetting the ROOm EQ PreparationsSetting the SPEAkER Setup When selecting the SPEAkER Configuration About the speaker sizeTo cancel the test tone function, press the Return button When selecting the Crossover FrequencyWhen selecting the Channel Level Press the Enter button to confirm your selectionWhen selecting the SPEAkER Distance About the speaker distanceWhen selecting the ROOm2 input Setting the mULTI ROOm SetupWhen the ROOm2 mode is set to on When selecting the ROOm2 volumeREmEDY Troubleshooting GuidePROBLEm Specifications Setup Code Table Inno HIT DOCK-VCR Otto Verand BD/DVD SAT AUX-USB/MD 904