Sherwood R-904 Setting the SYSTEm, ①. Press the Enter button to enter the tone adjustment mode

Page 35

R-904(G)_ENG_091014:R-904(G) 2009-11-11 오후 12:05 페이지 35

SETTING THE SYSTEm

AMP : BACK / R2
TONE : OFF / ON			TRE : 0 / -10 ~ +10
TONE : OFF / ON			TRE : 0 / -10 ~ +10
			BASS : 0 / -10 ~ +10
			BASS : 0 / -10 ~ +10

•AMP (AMP ASSIGN) : To assign the surround back channels' power amplifier correctly depending on how to use the speakers.

•TONE : To adjust the tone (bass and treble) as desired.

1. Press the CURSOR UP/DOWN buttons to select the desired item.

2. Press the CURSOR LEFT/RIGHT buttons to set the selected item as desired.

■When selecting the AmP ASSIGN

•The surround back channels' power amplifier can drive the surround back speakers or the ROOM 2 speakers. Depending on how to use the speakers, you should assign the power amplifier correctly. (For details, refer to “CONNECTING SPEAKERS” on page 7 and “CONNECTING ROOM2 SPEAKERS” on page 8.)

BACK (SURROUND BACK) : To drive the surround back speakers when connecting the SURROUND BACK/ROOM2 channels

↕	to them.

R2 (ROOM2) : To drive the ROOM2 speakers when connecting the SURROUND BACK/ROOM2 channels to them.

■When selecting the TONE

OFF : To listen to a program source without the tone effect. (“DIR” lights up.)

↕

ON : To adjust the tone for your taste. (“DIR” goes off.)

◆When the TONE CONTROL is set to ON to adjust the tone (bass and treble)

①. Press the ENTER button to enter the tone adjustment mode.

• Then “TRE ~” will be displayed.

②. Press the CURSOR UP/DOWN buttons to select the desired tone mode.

③. Press the CURSOR LEFT/RIGHT buttons to adjust the selected tone as desired.

•The tone level can be adjusted within the range of -10 ~ +10 dB.

•In general, we recommend the bass and treble to be adjusted to 0 dB (flat level).

•Extreme settings at high volume may damage your speakers.

•To complete tone adjustment, repeat the above steps ② and ③.

ENGLISH

35

Image 35

Contents 904 Read this Before Operating Your Unit IntroductionContents System Connections Connecting Audio COmPONENTConnecting Video COmPONENTS Copyright protection system HDmI High Definition multimedia Interface connection *1Connecting speaker wire Connecting SPEAkERSConnecting ROOm2 SPEAkERS Speaker placementConnecting for SYSTEm Control Fluorescent Display Front Panel ControlsFront AUx JACk Setup mIC JACkMACROM1~M3 buttons Universal Remote ControlsSound Parameter button Numeric 0~9, +10 Sleep button Input Selector buttonsStop Function Table of the Numbered ButtonsOPeRAtInG coMPonentsWItH ReMote contRoL LoADInG BAtteRIes ReMote contRoL oPeRAtIon RAnGeRepeat the above steps 1 to 4 for each of your Components UsInG FUnctIons oF ReMote contRoLEntering a setup code Removing all punch-through functions Using a punch-through functionRemoving a punch-through function Operating a macro function Programming a macro functionBefore operation OperationsListening to a PROGRAm Source Select the digital or analog input connected as desired Listening with headphonesAdjust the overall volume Muting the soundSurround modes SURRoUnD soUnDHall StadiumClassic MoviePress the Sound Parameter button When adjusting the sound parametersWhen selecting the Dm Dual mono When selecting the EQ Room EQWhen selecting the L.SYNC Lip-Sync When selecting the A.DLY Auto Delay When selecting the DRC Dynamic Range ControlWhen selecting the LFE LFE level When selecting the HDmI HDmI Audio Out①. Press the Enter button to enter the Dolby Volume setup Select the desired channel Adjusting the current channel levelAdjust the level of the selected channel as desired Repeat the above steps 1 and 2 to adjust each channel levelPress the Tuning buttons for more than 0.5 second Auto tuningManual tuning Auto presettingPress the Enter button Presetting radio stationsTuning to preset stations TuningWhile displaying SEARCH, select the desired program type FM mode, press the Search Mode buttonListening to RDS BROADCASTSFm only Searching for stations by program typeDisplaying RDS information Adjusting the brightness of the fluorescent display Operating the sleep timerSelect the desired input as a ROOM2 source ROOm2 Source PLAYBACkTurn on the ROOM2 function Turn the setup menu on System SetupSET Rmeq Setup menu flow①. Press the Enter button to enter the tone adjustment mode Setting the SYSTEmPreparations Setting the ROOm EQSetting the SPEAkER Setup About the speaker size When selecting the SPEAkER ConfigurationPress the Enter button to confirm your selection When selecting the Crossover FrequencyWhen selecting the Channel Level To cancel the test tone function, press the Return buttonAbout the speaker distance When selecting the SPEAkER DistanceWhen selecting the ROOm2 volume Setting the mULTI ROOm SetupWhen the ROOm2 mode is set to on When selecting the ROOm2 inputREmEDY Troubleshooting GuidePROBLEm Specifications Setup Code Table Inno HIT DOCK-VCR Otto Verand BD/DVD SAT AUX-USB/MD 904