Sherwood R-904 manual Connecting SPEAkERS, Connecting speaker wire

Page 7

R-904(G)_ENG_091014:R-904(G) 2009-11-11 오후 12:05 페이지 7

6. CONNECTING SPEAkERS

• Be sure to connect speakers firmly and correctly according to the channel(left and right) and the polarity (+ and -). If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connection is incorrect, the sound will be unnatural and lack bass.

• When using only one surround back speaker, you should connect it to SURROUND BACK/ ROOM2 LEFT channel.

•Because this receiver cannot drive the surround back speakers and the ROOM2 speakers

simultaneously, you should assign their power amplifier correctly depending on how to use them. (For details, refer to "CONNECTING ROOM2 SPEAKERS" on page 8 and "When selecting the AMP ASSIGN" on page 35.)

• For installing the speakers, refer to "Speaker placement" on page 8.

• After installing the speakers, first adjust the speaker settings according to your environment and speaker layout. (For details, refer to "SETTING THE ROOM EQ" on page 36.)

Caution :

• Be sure to use the speakers with the impedance of 6 ohms or above.

•Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the speakers.

•Never touch the speaker terminals while the AC input cord is connected to the wall AC outlet. Doing so could result in electric shocks.

■Connecting speaker wire

1. Strip away approx. 10 mm			2. Loosen by turning the	3. Insert the bare part of the			4. Tighten by turning it
(3/8 inch) of wire insulation,			speaker terminal counter-	wire.			clockwise.
then twist the wire ends			clockwise.


tight.

ENGLISH

7

Image 7

Contents 904 Read this Before Operating Your Unit IntroductionContents System Connections Connecting Audio COmPONENTConnecting Video COmPONENTS Copyright protection system HDmI High Definition multimedia Interface connection *1Connecting speaker wire Connecting SPEAkERSConnecting ROOm2 SPEAkERS Speaker placementConnecting for SYSTEm Control Fluorescent Display Front Panel ControlsFront AUx JACk Setup mIC JACkMACROM1~M3 buttons Universal Remote ControlsSound Parameter button Numeric 0~9, +10 Sleep button Input Selector buttonsStop Function Table of the Numbered ButtonsOPeRAtInG coMPonentsWItH ReMote contRoL LoADInG BAtteRIes ReMote contRoL oPeRAtIon RAnGeEntering a setup code UsInG FUnctIons oF ReMote contRoLRepeat the above steps 1 to 4 for each of your Components Removing a punch-through function Using a punch-through functionRemoving all punch-through functions Operating a macro function Programming a macro functionListening to a PROGRAm Source OperationsBefore operation Select the digital or analog input connected as desired Listening with headphonesAdjust the overall volume Muting the soundSurround modes SURRoUnD soUnDHall StadiumClassic MoviePress the Sound Parameter button When adjusting the sound parametersWhen selecting the L.SYNC Lip-Sync When selecting the EQ Room EQWhen selecting the Dm Dual mono When selecting the A.DLY Auto Delay When selecting the DRC Dynamic Range ControlWhen selecting the LFE LFE level When selecting the HDmI HDmI Audio Out①. Press the Enter button to enter the Dolby Volume setup Select the desired channel Adjusting the current channel levelAdjust the level of the selected channel as desired Repeat the above steps 1 and 2 to adjust each channel levelPress the Tuning buttons for more than 0.5 second Auto tuningManual tuning Auto presettingPress the Enter button Presetting radio stationsTuning to preset stations TuningWhile displaying SEARCH, select the desired program type FM mode, press the Search Mode buttonListening to RDS BROADCASTSFm only Searching for stations by program typeDisplaying RDS information Adjusting the brightness of the fluorescent display Operating the sleep timerTurn on the ROOM2 function ROOm2 Source PLAYBACkSelect the desired input as a ROOM2 source Turn the setup menu on System SetupSET Rmeq Setup menu flow①. Press the Enter button to enter the tone adjustment mode Setting the SYSTEmPreparations Setting the ROOm EQSetting the SPEAkER Setup About the speaker size When selecting the SPEAkER ConfigurationPress the Enter button to confirm your selection When selecting the Crossover FrequencyWhen selecting the Channel Level To cancel the test tone function, press the Return buttonAbout the speaker distance When selecting the SPEAkER DistanceWhen selecting the ROOm2 volume Setting the mULTI ROOm SetupWhen the ROOm2 mode is set to on When selecting the ROOm2 inputPROBLEm Troubleshooting GuideREmEDY Specifications Setup Code Table Inno HIT DOCK-VCR Otto Verand BD/DVD SAT AUX-USB/MD 904