Sherwood R-904 manual Setting the ROOm EQ, Preparations

Page 36

R-904(G)_ENG_091014:R-904(G) 2009-11-11 오후 12:05 페이지 36

ENGLISH

SETTING THE ROOm EQ

•Room EQ lets you avoid troublesome listening-based speaker setup and achieve good surround sound. Room EQ has the feature that provides the optimum listening environment at the listening position in your room. You should connect the supplied microphone to the SETUP MIC jack so that this receiver can analyze the information form a series of test tones emitted from speakers at listening position and can adjust the size, channel level, distance and frequency response of each speaker automatically.

•If you want to personalize your speaker setup by making the settings manually, perform the “SETTING THE SPEAKER SETUP” on page 37.

•After the Room EQ setup has been completed, set the Room EQ as desired. (For details, refer to “When selecting the “EQ (Room EQ)” on page 23.)

■Preparations

①. Check that the speakers are securely connected to this receiver.

•If your subwoofer has adjustable volume and crossover frequency, set the volume halfway and set the crossover frequency to the maximum or the low pass filter off.

②. Connect the supplied microphone to the SETUP MIC jack on the front panel.(For details, refer to “SETUP MIC JACK” on page 11.)

■Notes :

•Because the microphone for Room EQ setup is designed for use with this receiver, to use the Room EQ setup function, do not use a microphone other than the one supplied with this receiver.

•After you have completed the Room EQ setup procedure, disconnect the microphone.

1. Place the microphone on a flat level surface at the listening position.

•If possible, use a tripod, etc. to attach the microphone at the same height as your ears would be when you are seated in your listening position.

•Ensure there are no obstacles between the speakers and the microphone.

2. Press the ENTER button to check the speaker configuration when “SET RMEQ” is displayed.

•“SET RMEQ” flickers while the receiver outputs the test tones to determine the speakers present in your setup and then “CHECK OK” is displayed.

■Notes :

•Try to be as quiet as possible while outputting the test tones.

•For correct speaker settings, do not adjust the volume while outputting the test tones.

•If there is too much ambient noise, error message will be displayed.

In such a case, press the ENTER button to confirm “RETRY?” after checking for ambient noise.

•If there may be a problem with speaker connection, “ERR ~” (error message) will be displayed.

If confirming “RETRY?” with pressing the ENTER button does not fix the problem, turn off the power and check the speaker connection.

3. To check the speaker configuration, press the CURSOR UP/DOWN buttons to select the speaker.

•Each time the CURSOR UP/DOWN buttons are pressed, the speaker is changed.

•If the speaker configuration is not correct, press the CURSOR LEFT/RIGHT buttons to change the setting. When the correction is finished, confirm the speaker configuration.

4. To confirm the speaker configuration, press the CURSOR UP/DOWN buttons to select “CHECK OK”, then press the ENTER button.

•Then the Room EQ setup will start.

•If any operation is not performed while displaying “CHECK OK” for 10 seconds, the Room EQ setup will start automatically.

5. If the Room EQ setup has been completed, it will be returned to the Room EQ setup.

•Then the settings made in the Room EQ setup are memorized. You can check these settings on the “SPEAKER SETUP” menu. (For details, refer to “SETTING THE SPEAKER SETUP” on page 37.)

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents 904 Introduction Read this Before Operating Your UnitContents Connecting Audio COmPONENT System ConnectionsConnecting Video COmPONENTS HDmI High Definition multimedia Interface connection *1 Copyright protection systemConnecting SPEAkERS Connecting speaker wireSpeaker placement Connecting ROOm2 SPEAkERSConnecting for SYSTEm Control Front Panel Controls Fluorescent DisplaySetup mIC JACk Front AUx JACkUniversal Remote Controls Sound Parameter buttonNumeric 0~9, +10 Sleep button Input Selector buttons MACROM1~M3 buttonsFunction Table of the Numbered Buttons StopLoADInG BAtteRIes ReMote contRoL oPeRAtIon RAnGe OPeRAtInG coMPonentsWItH ReMote contRoLUsInG FUnctIons oF ReMote contRoL Entering a setup codeRepeat the above steps 1 to 4 for each of your Components Using a punch-through function Removing a punch-through functionRemoving all punch-through functions Programming a macro function Operating a macro functionOperations Listening to a PROGRAm SourceBefore operation Listening with headphones Adjust the overall volumeMuting the sound Select the digital or analog input connected as desiredSURRoUnD soUnD Surround modesStadium ClassicMovie HallWhen adjusting the sound parameters Press the Sound Parameter buttonWhen selecting the EQ Room EQ When selecting the L.SYNC Lip-SyncWhen selecting the Dm Dual mono When selecting the DRC Dynamic Range Control When selecting the LFE LFE levelWhen selecting the HDmI HDmI Audio Out When selecting the A.DLY Auto Delay①. Press the Enter button to enter the Dolby Volume setup Adjusting the current channel level Adjust the level of the selected channel as desiredRepeat the above steps 1 and 2 to adjust each channel level Select the desired channelAuto tuning Manual tuningAuto presetting Press the Tuning buttons for more than 0.5 secondPresetting radio stations Tuning to preset stationsTuning Press the Enter buttonFM mode, press the Search Mode button Listening to RDS BROADCASTSFm onlySearching for stations by program type While displaying SEARCH, select the desired program typeDisplaying RDS information Operating the sleep timer Adjusting the brightness of the fluorescent displayROOm2 Source PLAYBACk Turn on the ROOM2 functionSelect the desired input as a ROOM2 source System Setup Turn the setup menu onSetup menu flow SET RmeqSetting the SYSTEm ①. Press the Enter button to enter the tone adjustment modeSetting the ROOm EQ PreparationsSetting the SPEAkER Setup When selecting the SPEAkER Configuration About the speaker sizeWhen selecting the Crossover Frequency When selecting the Channel LevelTo cancel the test tone function, press the Return button Press the Enter button to confirm your selectionWhen selecting the SPEAkER Distance About the speaker distanceSetting the mULTI ROOm Setup When the ROOm2 mode is set to onWhen selecting the ROOm2 input When selecting the ROOm2 volumeTroubleshooting Guide PROBLEmREmEDY Specifications Setup Code Table Inno HIT DOCK-VCR Otto Verand BD/DVD SAT AUX-USB/MD 904
Top Page Image Contents