Sherwood R-772 manual Room 2 Source Playback, Vol ~, TAPE, Video 1 ~ Video

R-772(A)2007.8.165:21PM페이지44

ENGLISH

ROOM 2 SOURCE PLAYBACK

•This function allows enjoying one source in the main room and playing another in a different room at the same time.

•When you connect the multi-room system kit to the IR IN jack of this receiver, you can control this receiver with not only the universal remote control unit but also the ROOM 2 remote control unit in a different room, too. (For details, refer to "CONNECTING MULTI-ROOM SYSTEM KIT" on page 13 and "ROOM 2 Remote Controls" on page 29.)

�Notes:

•The analog signals from the EXTERNAL INs and the digital signals cannot be output to the different room, meaning no playback in a different room.

•You cannot play the ROOM 2 source in any surround mode.

■When using the buttons on the remote control unit.		■When using the buttons on the front panel.
1. Press the ROOM 2 button.		1. Press the ROOM 2 button to enter the ROOM 2 mode.
			• ROOM 2 ~ is displayed for several
	• ROOM 2 ~ is displayed for
			seconds.
	several seconds.
			• When the ROOM 2 setting mode
	• Each time this button is
			disappears, press the ROOM 2 button
	pressed, the ROOM 2		again.
	mode changes as follows :	2. Select the desired mode while displaying the ROOM 2
	OFF : To turn off the ROOM 2 function. ("R2" goes off .)
	�		setting mode.
	ON : To turn it on. ("R2" lights up.)
	�Note :		• Each time these buttons are
	• When the ROOM 2 mode is set to OFF, you cannot		pressed, the mode changes as
	adjust the ROOM 2 volume.		follows :
2. Select the desired input as a ROOM 2 source.			ROOM 2 ~	: To turn on or
			(ROOM 2 mode)	off the ROOM 2
			�	function.
	• Each time the INPUT button		IN ~ : To select the desired ROOM 2 source.
			(ROOM 2 input)
	on the universal remote		�
	control unit is pressed, the		VOL ~	: To adjust the volume on the power
	ROOM 2 input can be		(ROOM 2 volume)	amplifier assigned to "BACK ← →
	selected among MAIN			ROOM 2" or "ROOM 2".
	source, TUNER, CD, AUX,		�Note : When the ROOM 2 mode is set to OFF,
	TAPE, VIDEO 1 ~ VIDEO 4.
			the ROOM 2 input and the ROOM 2 volume
			cannot be selected
3. Adjust the ROOM 2 volume.		3. Set the selected mode as desired.
			■When selecting the ROOM 2 mode.
	• You can adjust the volume
			OFF : To turn off the ROOM 2
	on the power amplifier
			� function. ("R2" goes off.)
	assigned to "BACK ← →
			ON : To turn it on. ("R2" lights up.)
	ROOM 2" or "ROOM 2"
			■When selecting the ROOM 2 input.
	when the ROOM 2 speaker
	terminals are connected to		• You can select the desired among
			MAIN source, TUNER, CD, AUX,
	the speakers in a different
			TAPE, VIDEO 1 ~ VIDEO 4 as a ROOM 2 source.
	room. (For details, refer to "When selecting the AMP
			■When selecting the ROOM 2 volume.
	ASSIGN" on page 49.)
	• The MUTE button on the ROOM 2 remote control unit can		• You can adjust the volume on the power amplifier
			assigned to "BACK ← → ROOM 2" or "ROOM 2" when
	be available only when the ROOM 2 function is operating.
			the ROOM 2 speaker terminals are connected to the
4. Start play on the component related to the ROOM 2			speakers in a different room. (For details, refer to
			"When selecting the AMP ASSIGN" on page 49.)
	source.	4. Start play on the component related to the ROOM 2
			source.

�Notes:

•When the EXTERNAL IN is selected as a main input, if the MAIN source is selected as a ROOM 2 input, no audio signal can be heard in the different room (ROOM 2).

•Even when this receiver enters the standby mode, in such a case that "R2" lights up still and the POWER ON/STANDBY button lights up blue as it does in the operating mode, meaning only the ROOM 2 circuitry operates, the ROOM 2 source can be played independently.

•When you do not use the ROOM 2 function, turn off the ROOM 2 function to save electricity.

44