Sherwood R-772 manual When selecting the Hdmi Assign, When selecting the Video Assign

Page 54

R-772(A)2007.8.165:21PM페이지54

ENGLISH

Continued

When selecting the HDMI ASSIGN

•You should assign the connected HDMI INs to the desired of VIDEO 1 ~ VIDEO 4. (For details, refer to "CONNECTING VIDEO COMPONENTS" on pages 6 ~ 7.)

•You can select HDMI 1 or HDMI 2.

■Note :

•In such a case that a HDMI IN is assigned to two input sources or more, when these input sources are selected, the uncompressed digital video signals (and digital audio signals when the HDMI AUDIO OUT is set to ON) input into the same HDMI IN can be output from the HDMI MONITOR OUT of this receiver.

When selecting the VIDEO ASSIGN

•You should assign the connected COMPONENT VIDEO INs to the desired of VIDEO 1 ~ 4. (For details, refer to "CONNECTING VIDEO COMPONENTS" on pages 6 ~ 7.)

•You can select the desired of COMP 1 ~ 2.

■Note :

•In such a case that a COMPONENT VIDEO IN is assigned to two input sources or more, when these input sources are selected, the component video signals can be viewed from the same COMPONENT VIDEO IN.

When selecting the VIDEO MODE

• You can select the video input signal to be output from the MONITOR OUTs.

AUTO : When there are multiple video input signals, the video input signals are detected and the video input signal to be output from the MONITOR OUTs is selected automatically in the following order :

component video, S-video, composite video.

COMPOSITE : The signal that is input into the (COMPOSITE) VIDEO jack is always played. The composite video input signal is

up-converted and output from the S-VIDEO and COMPONENT MONITOR OUT jacks.

S-VIDEO : The signal that is input into the S-VIDEO jack is always played. The S-Video input signal is converted and

output from the (COMPOSITE) VIDEO and COMPONENT MONITOR OUT jacks.

COMPONENT : The signals that are input into the COMPONENT jacks are always played.

Because video conversion is not performed, no video signals are output from the MONITOR OUT jacks when there are no video signals that are input into the COMPONENT jacks.

•For details, refer to "Relationship between the video input signal and the video output signal" on page 7.

■Note :

•When selecting the VIDEO 4, S-VIDEO cannot be selected.

When selecting the AUDIO ASSIGN

•You should assign the connected DIGITAL INs to the desired of CD, AUX and VIDEO 1 ~ VIDEO 4. (For details, refer to "CONNECTING DIGITAL INS AND OUT" on page 9.)

•You can select the desired of OPT 1, OPT 2, COAX1 and COAX 2.

■Note :

•In such a case that a DIGITAL IN is assigned to two input sources or more, when these input sources are selected, the digital audio signals can be heard from the same DIGITAL IN.

When selecting the AUDIO MODE

•You can select the desired audio input signal to be played.

■Notes :

•Be sure to set the AUDIO MODE to the audio input which is connected and assigned to the selected input source.

•When the HDMI AUDIO OUT is set to ON, no sound will be heard from the speakers connected to this receiver (except ROOM 2 speakers).

•When the AUDIO MODE is set to HDMI, you should set the HDMI ASSIGN correctly. If not, "H1", "H2" (, meaning no digital audio signal input from it) or "Hd" (, meaning no HDMI assignment) flickers on the unit's display and no sound will be heard.

•When the AUDIO MODE is set to DIGITAL, you should set the AUDIO ASSIGN correctly. If not, "o1", "c1", etc.(, meaning no digital signal input from it) or "d" (, meaning no audio assignment) flickers on the unit's display and no sound will be heard.

AUTO : When there are multiple audio input signals, the audio input signals are detected and the audio input signal to be played is selected automatically in the priority order of them :

HDMI audio > DIGITAL audio > ANALOG audio HDMI : The signal that is input into the HDMI IN is always played.

DIGITAL : The signal that is input into the OPTICAL or the COAXIAL DIGITAL IN is always played.

ANALOG : The signal that is input into the analog AUDIO INs is always played.

54

Page 53 Page 55
Image 54
Page 53 Page 55
Contents 772A2007.8.16521PM페이지1 Safety Instructions Introduction Read this Before Operating Your UnitContents Connecting Antennas System ConnectionsConnecting Video Components Component in 1 Video 1, Component in 2 Video Component Video Composite VideoConnecting Audio Components Connecting External INSConnecting XM only for North America Connecting Subwoofer Preout Connecting Digital INS and OUTConnecting DC Trigger OUT Digital input default settingsSetting the SPEAKER/ROOM EQ Setup on Connecting SpeakersFor installing the speakers, refer to Speaker placement on Surround back speakersSurround left and right speakers Speaker placementFront left and right speakers and center speaker Surround back left and right speakersConnecting Room 2 Outs Connecting RF Remote AntennaFor details, refer to Changing the transmission signal on Connecting MULTI-ROOM System KIT Connecting PC for UpgradesSwitched AC Outlets AC Input CordPlug this cord into a wall AC outlet Front Panel Controls Remote SensorFluorescent Display Setup MIC Jack AUX in JackUniversal Remote Controls About the transmission signalFunction Table of the Numbered Buttons Loading Batteries Entering a setup code Learn RF-IR Delete Macro Code PunchSearching a setup code Code. Note772A2007.8.16521PM페이지22 Erasing the programmed command from one button Erasing all the commands programmed under a device modeProgramming a macro function To erase a macro programTo change a macro program Operating a macro function Programing a punch-through functionCase of the transport punch-through Operating a punch-through functionErasing the programmed puch-through function Case of the channel punch-through772A2007.8.16521PM페이지27 Changing the transmission signal Signal into RFRadio Frequency. NotesWhen RF is set to Loading Battery Room 2 Remote ControlsRemote Control Operation Range Remove the battery when it is not used for a long timeListening to a Program Source When selecting the External in as desiredOperations Before operationAdjust the overall volume When CD, AUX, Video 1~ 4 is selected as an input sourceListening with headphones Muting the soundSurround modes Dolby Virtual Speaker Reference Enjoying Surround Sound Dolby DIGITAL, Dolby VS REF, Dolby VS WideTo cancel the surround mode for stereo operation Listening in Dolby Headphone modeAdjusting each channel level with test tone 2CH downmix modeAdjusting the current channel level Select the desired channelMemorizing the adjusted channel levels Recalling the memorized channel levelsAuto presetting Auto tuningManual tuning Listening to Radio BroadcastsManual presetting Tuning to preset stationsScanning preset stations in sequence To sign up, access the website at Press the Tuner button repeatedly to select XM modePress the Tuning UP+/DOWN- buttons repeatedly to select XM XM Satellite Radio only for North AmericaChannel search XM mode, select the direct search modeXM mode, select the category search mode Direct searchError message and status Presetting channels Preset searchSignal strength display mode Displaying XM informationWhile operating the sleep timer, lights up Operating the sleep timerAdjusting the brightness of the fluorescent display Other FunctionsRoom 2 Source Playback VOL ~TAPE, Video 1 ~ Video Dubbing the audio and video signals separately onto Video RecordingRecording with Tape Dubbing from video components onto VideoOSD Menu Settings Multi772A2007.8.16521PM페이지48 When selecting the AMP Assign Setting the System SetupWhen selecting the items other than OSD Position Adjust Press the Cursor UP/DOWN buttons to select the desired itemWhen selecting the Subwoofer Mode When selecting the Hdmi Audio OUTWhen selecting the Tone Control When selecting the Cinema EQ When selecting the BackgroundWhen selecting the Momentary OSD When selecting the OSD Position Adjust Setting the Input Setup When selecting the items other than NameWhen selecting the menu of page 2 or When selecting the Video Mode When selecting the Hdmi AssignWhen selecting the Video Assign When selecting the Audio AssignWhen selecting the AV Sync When selecting the Auto SurroundWhen selecting the Audio Remaster When selecting the DC TriggerTo resume its factory input source name When selecting the NameConfirm your entry Name is stored in the memory Make a blank on each digit and press the Enter buttonSetting the Speaker / Room EQ Setup When selecting the Auto SetupPreparations 772A2007.8.16521PM페이지58 When selecting the Speaker Configuration When selecting the Speaker Distance About the speaker distanceWhen selecting the Speaker Crossover When selecting the Room EQ Setup When selecting the User mode Setting the CH Level Setup Reference Setting the Sound Parameter When selecting the Night ModeMAX When selecting the Center Width control When selecting the Dolby Plii MusicWhen selecting the Panorama mode When selecting the Dimension controlWhen selecting the Dolby Headphone When selecting the Dolby Virtual Speaker When selecting the Dolby Virtual Speaker Wide modeWhen selecting the Input Setting the Multi Room SetupWhen selecting the Room When selecting the VolumeTroubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier SectionSetup Code Table TMK RCASSS CCESTS KLHMEI ABC NSCSAT HTSNSM DKKMCS QED772A2007.8.16521PM페이지1
Related manuals
Manual 70 pages 5.16 Kb

R-772 specifications

The Sherwood R-772 is a versatile and powerful stereo receiver that appeals to audiophiles and casual listeners alike. This model, known for its robust performance and rich sound quality, is designed to meet the demands of modern audio systems while retaining classic features that enhance user experience.

One of the standout features of the Sherwood R-772 is its substantial power output. With the ability to deliver 100 watts per channel, this receiver can easily drive a wide range of speakers, providing dynamic and impactful audio that fills the room. This power output is complemented by its low total harmonic distortion, ensuring that the audio remains clean and detailed, even at higher volumes.

In terms of connectivity, the R-772 is equipped with multiple inputs for various audio sources. It includes several analog audio inputs, allowing users to connect their CD players, turntables, and other devices effortlessly. Additionally, the receiver supports AM/FM radio with a built-in tuner, providing access to a wide array of radio stations and programming. The inclusion of digital inputs enhances its compatibility with modern devices, ensuring an all-encompassing audio experience.

Another attractive feature of the Sherwood R-772 is its advanced surround sound processing. It supports various surround sound formats, enhancing the listening experience for movies and music. The inclusion of Dolby Pro Logic II allows users to enjoy stereo content in a multi-dimensional audio field, making movies and music come alive in their homes.

The R-772 is also designed with user convenience in mind. Its easy-to-navigate interface and remote control make it straightforward to operate, providing users with quick access to their favorite audio settings. The receiver also features a comprehensive equalization system, allowing users to personalize their listening experience and tailor the sound to their preferences.

Durability and build quality are characteristic of Sherwood products, and the R-772 is no exception. Its solid construction ensures longevity while maintaining aesthetic appeal. This model is designed to blend seamlessly with a home audio setup, offering both style and substance.

In conclusion, the Sherwood R-772 stereo receiver stands out with its powerful performance, versatile connectivity, and user-friendly features. It embodies a perfect balance of modern technology and traditional audio quality, ensuring that it remains a valuable addition to any audio system for years to come. This receiver is an excellent choice for anyone looking to enhance their listening experience, regardless of their level of audio expertise.
Top Page Image Contents