Sherwood R-772 manual OSD Menu Settings, Multi

Page 47

R-772(A)2007.8.165:21PM페이지47

OSD Menu Settings

•The OSD (On-Screen Display) menu is a setting menu that is displayed on the monitor TV and allows you to perform the setup procedures easily. In most situations, you will only need to set this once during the installation and layout of your home theater, and it rarely needs to be changed later.

The OSD menu consists of 6 main menus ; system setup, input setup, speaker / room EQ setup, CH level setup, sound parameter and multi room setup. These menus are then divided up into various sub-menus.

■Notes:

•The OSD menu and the momentary OSD cannot be displayed via the HDMI MONITOR OUT connector.

•Depending on the VIDEO MODE setting and the video connections between this receiver and the video component, the OSD menu and the momentary OSD cannot be displayed via (COMPOSITE) VIDEO MONITOR OUT jack, or the picture is automatically turned off and only the OSD menu can be displayed via COMPONENT MONITOR OUT jacks. (For details, refer to "Relationship between the video input signal and the video output signal" on page 7.)

■Navigating through the OSD menu

•The explanations here assume you are using the buttons on the remote control when performing the OSD menu operation. However, you can use the buttons on the front panel as well.

The buttons on the front panel correspond to those on the remote control as shown below.

1. Turn the menu screen on.

MULTI

•The main menu will be shown.

•To turn the menu screen off, press this button again.

2. Select the desired menu using the CURSOR UP(▲)/DOWN(▼) buttons.

ENGLISH

47

Image 47

Contents 772A2007.8.16521PM페이지1 Safety Instructions Read this Before Operating Your Unit IntroductionContents System Connections Connecting AntennasConnecting Video Components Component Video Composite Video Component in 1 Video 1, Component in 2 VideoConnecting XM only for North America Connecting Audio ComponentsConnecting External INS Digital input default settings Connecting Digital INS and OUTConnecting DC Trigger OUT Connecting Subwoofer PreoutSurround back speakers Connecting SpeakersFor installing the speakers, refer to Speaker placement on Setting the SPEAKER/ROOM EQ Setup onSurround back left and right speakers Speaker placementFront left and right speakers and center speaker Surround left and right speakersFor details, refer to Changing the transmission signal on Connecting Room 2 OutsConnecting RF Remote Antenna Connecting PC for Upgrades Connecting MULTI-ROOM System KITPlug this cord into a wall AC outlet Switched AC OutletsAC Input Cord Fluorescent Display Front Panel ControlsRemote Sensor AUX in Jack Setup MIC JackAbout the transmission signal Universal Remote ControlsFunction Table of the Numbered Buttons Loading Batteries Learn RF-IR Delete Macro Code Punch Entering a setup codeCode. Note Searching a setup code772A2007.8.16521PM페이지22 Erasing all the commands programmed under a device mode Erasing the programmed command from one buttonTo change a macro program Programming a macro functionTo erase a macro program Programing a punch-through function Operating a macro functionCase of the channel punch-through Operating a punch-through functionErasing the programmed puch-through function Case of the transport punch-through772A2007.8.16521PM페이지27 When RF is set to Changing the transmission signalSignal into RFRadio Frequency. Notes Remove the battery when it is not used for a long time Room 2 Remote ControlsRemote Control Operation Range Loading BatteryBefore operation When selecting the External in as desiredOperations Listening to a Program SourceMuting the sound When CD, AUX, Video 1~ 4 is selected as an input sourceListening with headphones Adjust the overall volumeSurround modes Dolby Virtual Speaker Reference Dolby DIGITAL, Dolby VS REF, Dolby VS Wide Enjoying Surround Sound2CH downmix mode Listening in Dolby Headphone modeAdjusting each channel level with test tone To cancel the surround mode for stereo operationSelect the desired channel Adjusting the current channel levelRecalling the memorized channel levels Memorizing the adjusted channel levelsListening to Radio Broadcasts Auto tuningManual tuning Auto presettingScanning preset stations in sequence Manual presettingTuning to preset stations XM Satellite Radio only for North America Press the Tuner button repeatedly to select XM modePress the Tuning UP+/DOWN- buttons repeatedly to select XM To sign up, access the website atDirect search XM mode, select the direct search modeXM mode, select the category search mode Channel searchDisplaying XM information Presetting channels Preset searchSignal strength display mode Error message and statusOther Functions Operating the sleep timerAdjusting the brightness of the fluorescent display While operating the sleep timer, lights up TAPE, Video 1 ~ Video Room 2 Source Playback VOL ~ Recording with Tape Dubbing the audio and video signals separately onto VideoRecording Video Dubbing from video components ontoMulti OSD Menu Settings772A2007.8.16521PM페이지48 Press the Cursor UP/DOWN buttons to select the desired item Setting the System SetupWhen selecting the items other than OSD Position Adjust When selecting the AMP AssignWhen selecting the Tone Control When selecting the Subwoofer ModeWhen selecting the Hdmi Audio OUT When selecting the Momentary OSD When selecting the Cinema EQWhen selecting the Background When selecting the OSD Position Adjust When selecting the menu of page 2 or Setting the Input SetupWhen selecting the items other than Name When selecting the Audio Assign When selecting the Hdmi AssignWhen selecting the Video Assign When selecting the Video ModeWhen selecting the DC Trigger When selecting the Auto SurroundWhen selecting the Audio Remaster When selecting the AV SyncMake a blank on each digit and press the Enter button When selecting the NameConfirm your entry Name is stored in the memory To resume its factory input source namePreparations Setting the Speaker / Room EQ SetupWhen selecting the Auto Setup 772A2007.8.16521PM페이지58 When selecting the Speaker Configuration About the speaker distance When selecting the Speaker DistanceWhen selecting the Speaker Crossover When selecting the Room EQ Setup When selecting the User mode Setting the CH Level Setup Reference MAX Setting the Sound ParameterWhen selecting the Night Mode When selecting the Dimension control When selecting the Dolby Plii MusicWhen selecting the Panorama mode When selecting the Center Width controlWhen selecting the Dolby Headphone When selecting the Dolby Virtual Speaker Wide mode When selecting the Dolby Virtual SpeakerWhen selecting the Volume Setting the Multi Room SetupWhen selecting the Room When selecting the InputProblem Possible Cause Remedy Troubleshooting GuideAmplifier Section SpecificationsSetup Code Table CCE RCASSS TMKMEI STSKLH NSC ABCHTS SATQED DKKMCS NSM772A2007.8.16521PM페이지1

Related manuals

Manual 70 pages 5.16 Kb