GE EGR3000 Tips, How to Set the Oven for Baking or Roasting, Preheating and Pan Placement

Page 13

www.GEAppliances.com

Do not lock the oven door with the latch during baking or roasting. The latch is used for self-cleaning only.

How to Set the Oven for Baking or Roasting

Safety

The oven has a special low shelf (R) position just above the oven bottom. Use it when extra cooking space is needed, for example, when cooking a large turkey. The shelf is not designed to slide out at this position.

Your oven is not designed for open-door cooking.

Touch the BAKE pad.

Touch the + or – pads until the desired temperature is displayed.

Touch the START/ON pad.

The oven will start automatically. The display will show PRE while preheating. When the oven reaches the selected temperature, the oven control will beep several times and the display will show the oven temperature.

To change the oven temperature during BAKE cycle, touch the BAKE pad and then the + or – pads to get the new temperature.

Check food for doneness at minimum time on recipe. Cook longer if necessary.

Touch the CLEAR/OFF pad when baking is finished and then remove the food from the oven.

Type of Food

Shelf Position

Frozen pies (on cookie sheet)

B or C

 

 

Angel food cake,

B

bundt or pound cakes

 

 

 

Biscuits, muffins, brownies,

C

cookies, cupcakes,

 

layer cakes, pies

 

 

 

Casseroles

B or C

 

 

Roasting

R or A

 

 

Instructions Operating Instructions Installation

Preheating and Pan Placement

Preheat the oven if the recipe calls for it. To preheat, set the oven at the correct temperature. Preheating is necessary for good results when baking cakes, cookies, pastry and breads.

For ovens without a preheat indicator light or tone, preheat 10 minutes.

Baking results will be better if baking pans are centered in the oven as much as possible. Pans should not touch each other or the walls of the oven. If you need to use two shelves, stagger the pans so one is not directly above the other, and leave approximately 11⁄2″ between pans, from the front, back and sides of the wall.

Instructions Troubleshooting

 

Aluminum Foil

 

Never cover the oven bottom with

 

aluminum foil.

 

You can use aluminum foil to line the

 

broiler pan and broiler grid. However,

 

you must mold the foil tightly to the

Cut slits in the foil just like the grid.

grid and cut slits in it just like the grid.

Aluminum foil may also be used to catch a spillover. To do so, place a small sheet of foil on a lower shelf several inches below the food.

Never entirely cover a shelf with aluminum foil. This will disturb the heat circulation and result in poor baking.

Tips

Oven Moisture

As your oven heats up, the temperature change of the air in the oven may cause water droplets to form on the door glass. These droplets are harmless and will evaporate as the oven continues to heat up.

13

Consumer Support

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Write the model and serial numbers here Model # Serial # RangesSelf-Cleaning GasAll ranges can tip and injury could result ANTI-TIP DeviceImportant Safety Notice Instructions Surface Burners Cook Meat and Poultry THOROUGHLY… Instructions Operating Instructions SELF-CLEANING OvenInstructions Using the gas surface burnersInstructions Operating ConsumerCase of Power Failure SafetyTop-of-Range Cookware Consumer Support Troubleshooting Tips Using the oven controlsInstallation Instructions Oven Control, Clock and Timer Features and Settings Consumer Support Using the ovenPreheating and Pan Placement How to Set the Oven for Baking or RoastingTips Aluminum FoilBroiling Guide How to Set the Oven for BroilingHI Broil Installation Using the clock and timerTo Set the Timer To Set the ClockTo Cancel the Timer To Reset the TimerTouch the Kitchen Timer ON/OFF End of Cycle Tones on some modelsHow to Set a Delayed Start and Automatic Stop Using the timed baking and roasting featuresSafety Instructions Special features of your oven controlHour Shut-Off Safety Instructions Using the Sabbath Feature. on some modelsHow to Set for Regular Baking/Roasting Designed for use on the Jewish Sabbath and HolidaysHow to Exit the Sabbath Feature Instructions Troubleshooting Tips Consumer Support Adjust the oven thermostat-Do it yourselfTo Adjust the Thermostat Type of margarine will affect baking performanceBefore a Clean Cycle Using the self-cleaning ovenHow to Set the Oven for Cleaning To Stop a Clean Cycle How to Delay the Start of CleaningAfter a Clean Cycle Tips Consumer SupportStandard Twin Burner Assemblies on some models Care and cleaning of the rangeSafety Replacement After cleaningBurner caps Burner headsBurner Grates Troubleshooting Tips Consumer SupportCooktop Surface To OrderLift-Off Oven Door Troubleshooting TipsOven Bottom Broiler Pan and GridRemovable Storage Drawer on some models Removable Kick Panel on some modelsLower Control Panel Front Manifold Panel and Knobs Oven Air VentsOven Shelves Oven Light ReplacementDo not remove any screws to remove the cover To replace coverPart Included For Your SafetyTools YOU will Need Materials YOU MAY NeedInstallation Instructions Dimensions and Clearances Location ANTI-TIP DeviceProvide Adequate GAS Supply Connect the Range to GASInstallation Instructions Rigid Pipe Hookup Options Pressure regulator Manifold pipe Electrical Requirements Electrical ConnectionsSeal the Openings Check Ignition of Surface BurnersCheck Ignition of Oven Burner To remove the oven bottom Leveling the RangeWhen ALL Hookups are Completed Installing the ANTI-TIP DeviceProblem Possible Causes What To Do Before you call for service…See the Care and cleaning of the range section See the Using the clock and timer sectionSee the Installation of the range section Oven temperatureClean cycle After a clean cycle Oven not clean afterExcessive smoking Oven door will notClock flashes Power outageEmitting from the vent Strong odorOperating Instructions Safety Instructions We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Page Consumer Support Looking For Something More? AccessoriesOperating Instructions Safety InstructionsGE Will Replace What GE Will Not CoverWhat Camco Will Not Cover Camco Will ReplaceParts and Accessories Schedule ServiceConsumer Support GE Appliances Website Real Life Design Studio

EGR3000 specifications

The GE EGR3000 is a cutting-edge gas turbine engine designed to meet the demands of modern power generation and transportation applications. This innovative engine showcases a range of advanced features and technologies that enhance its performance, efficiency, and reliability.

One of the key characteristics of the EGR3000 is its exceptional efficiency. The engine employs an advanced thermodynamic cycle, which incorporates a high compression ratio and an innovative cooling design. This efficiency is particularly important in reducing fuel consumption and emissions, making it an environmentally friendly option compared to traditional gas turbines. The EGR3000 boasts a thermal efficiency rating that places it among the highest in its class.

The EGR3000 utilizes a dual-fuel capability, allowing it to operate on a variety of fuels. This flexibility is crucial for operators looking to optimize their fuel use based on availability and cost, adding to the engine's versatility. Additionally, the engine is designed to accommodate both natural gas and liquid fuels, thereby enhancing its operational range.

Another notable feature is the engine's advanced modular design. This allows for easier maintenance and quicker turnaround times, minimizing downtime and operational costs for power plants and industrial facilities. The modular components can be replaced or serviced individually, which simplifies maintenance procedures and enhances overall reliability.

In terms of technology, the EGR3000 incorporates sophisticated materials and coatings that improve thermal resistance and durability. High-performance blades and combustion chambers are designed to withstand extreme temperatures, resulting in longer service life and reduced maintenance frequency. The engine also employs digital control systems that optimize performance parameters in real-time, ensuring peak efficiency under varying load conditions.

Emissions control is a critical aspect of the EGR3000's design. It features advanced combustion technology that minimizes NOx and CO2 emissions, aligning with stringent environmental regulations. The engine's design enables it to operate with lean-burn technology, further supporting reduced environmental impact.

Overall, the GE EGR3000 stands out as a powerful and efficient gas turbine solution. Its combination of high efficiency, fuel flexibility, modular design, and advanced emission control technologies makes it an ideal choice for various applications, including power generation and industrial processes. As energy demands continue to evolve, the EGR3000 positions itself as a reliable and forward-thinking solution for today’s energy landscape.
Top Page Image Contents