GE EGR3000 Using the self-cleaning oven, Before a Clean Cycle, How to Set the Oven for Cleaning

Page 22

Instructions

Using the self-cleaning oven.

Never force the latch handle. Forcing the handle will damage the door lock mechanism. The oven door must be closed and all controls set correctly for the cycle to work properly.

Instructions Operating Instructions Safety

Wipe up heavy soil on the oven bottom.

Before a Clean Cycle

For the first self-clean cycle, we recommend venting your kitchen with an open window or using a ventilation fan or hood.

Remove the shelves, broiler pan, broiler grid, all cookware and any aluminum foil from the oven.

The oven shelves can be self-cleaned, but they will darken, lose their luster and become hard to slide.

Do not use commercial oven cleaners or oven protectors in or near the self-cleaning oven. A combination of any of these products plus the high clean cycle temperatures may damage the porcelain finish of the oven.

Soil on the front frame of the range and outside the gasket on the door will need to be cleaned by hand. Clean these areas with hot water, soap-filled scouring pads or cleansers such as Soft Scrub®.

Rinse well with clean water and dry.

Do not clean the gasket. The fiberglass material of the oven door gasket cannot withstand abrasion. It is essential for the gasket to remain intact. If you notice it becoming worn or frayed, replace it.

Wipe up any heavy spillovers on the oven bottom.

Make sure the oven light bulb cover is in place and the oven light is off.

CAUTION: The grates and drip pans (on some models) should never be cleaned in the self-cleaning oven.

Do not use commercial oven cleaners or oven protectors in or near the self-cleaning oven.

A combination of any of these products plus the high clean cycle temperatures may damage the porcelain finish of the oven.

IMPORTANT: The health of some birds is extremely sensitive to the fumes given off during the self-cleaning cycle of any range. Move birds to another well ventilated room.

Consumer Support Troubleshooting Tips Installation

How to Set the Oven for Cleaning

Follow the directions in the Before a Clean Cycle section.

Latch the door.

NOTE: Never force the latch. If the oven is too hot, you will not be able to slide the latch. Allow the oven to cool.

Touch the SELF CLEAN pad.

Touch the + or – pads until the desired Clean Time is displayed.

The Clean Time is normally 4 hours and 20 minutes. You can change the Clean Time to any time between 3 and 5 hours, depending on the amount of soil in your oven.

Touch the START/ON pad.

The self-clean cycle will automatically begin after CLEAN is displayed and the time countdown appears in the display.

While the oven is self-cleaning, you can touch the CLOCK pad to display the time of day. To return to the clean countdown, touch the SELF CLEAN pad.

The oven shuts off automatically when the clean cycle is complete, and 0:00 will flash in the display.

Slide the latch handle to the left as far as it will go and open the door.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents RangesSelf-Cleaning Gas Write the model and serial numbers here Model # Serial #ANTI-TIP Device All ranges can tip and injury could resultImportant Safety Notice Instructions Surface Burners Cook Meat and Poultry THOROUGHLY… SELF-CLEANING Oven Instructions Operating InstructionsInstructions Operating Using the gas surface burnersInstructions ConsumerCase of Power Failure SafetyTop-of-Range Cookware Consumer Support Troubleshooting Tips Using the oven controlsInstallation Instructions Oven Control, Clock and Timer Features and Settings Using the oven Consumer SupportTips How to Set the Oven for Baking or RoastingPreheating and Pan Placement Aluminum FoilBroiling Guide How to Set the Oven for BroilingHI Broil To Set the Timer Using the clock and timerInstallation To Set the ClockTouch the Kitchen Timer ON/OFF To Reset the TimerTo Cancel the Timer End of Cycle Tones on some modelsUsing the timed baking and roasting features How to Set a Delayed Start and Automatic StopSafety Instructions Special features of your oven controlHour Shut-Off How to Set for Regular Baking/Roasting Using the Sabbath Feature. on some modelsSafety Instructions Designed for use on the Jewish Sabbath and HolidaysHow to Exit the Sabbath Feature To Adjust the Thermostat Adjust the oven thermostat-Do it yourselfInstructions Troubleshooting Tips Consumer Support Type of margarine will affect baking performanceBefore a Clean Cycle Using the self-cleaning ovenHow to Set the Oven for Cleaning After a Clean Cycle How to Delay the Start of CleaningTo Stop a Clean Cycle Tips Consumer SupportCare and cleaning of the range Standard Twin Burner Assemblies on some modelsSafety Burner caps After cleaningReplacement Burner headsCooktop Surface Troubleshooting Tips Consumer SupportBurner Grates To OrderOven Bottom Troubleshooting TipsLift-Off Oven Door Broiler Pan and GridRemovable Kick Panel on some models Removable Storage Drawer on some modelsOven Air Vents Lower Control Panel Front Manifold Panel and KnobsDo not remove any screws to remove the cover Oven Light ReplacementOven Shelves To replace coverTools YOU will Need For Your SafetyPart Included Materials YOU MAY NeedInstallation Instructions Dimensions and Clearances ANTI-TIP Device LocationConnect the Range to GAS Provide Adequate GAS SupplyInstallation Instructions Rigid Pipe Hookup Options Pressure regulator Manifold pipe Electrical Connections Electrical RequirementsSeal the Openings Check Ignition of Surface BurnersCheck Ignition of Oven Burner Leveling the Range To remove the oven bottomInstalling the ANTI-TIP Device When ALL Hookups are CompletedBefore you call for service… Problem Possible Causes What To DoSee the Installation of the range section See the Using the clock and timer sectionSee the Care and cleaning of the range section Oven temperatureExcessive smoking After a clean cycle Oven not clean afterClean cycle Oven door will notEmitting from the vent Power outageClock flashes Strong odorOperating Instructions Safety Instructions We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Page Consumer Support Accessories Looking For Something More?GE Will Replace Instructions Safety InstructionsOperating What GE Will Not CoverCamco Will Replace What Camco Will Not CoverConsumer Support GE Appliances Website Schedule ServiceParts and Accessories Real Life Design Studio

EGR3000 specifications

The GE EGR3000 is a cutting-edge gas turbine engine designed to meet the demands of modern power generation and transportation applications. This innovative engine showcases a range of advanced features and technologies that enhance its performance, efficiency, and reliability.

One of the key characteristics of the EGR3000 is its exceptional efficiency. The engine employs an advanced thermodynamic cycle, which incorporates a high compression ratio and an innovative cooling design. This efficiency is particularly important in reducing fuel consumption and emissions, making it an environmentally friendly option compared to traditional gas turbines. The EGR3000 boasts a thermal efficiency rating that places it among the highest in its class.

The EGR3000 utilizes a dual-fuel capability, allowing it to operate on a variety of fuels. This flexibility is crucial for operators looking to optimize their fuel use based on availability and cost, adding to the engine's versatility. Additionally, the engine is designed to accommodate both natural gas and liquid fuels, thereby enhancing its operational range.

Another notable feature is the engine's advanced modular design. This allows for easier maintenance and quicker turnaround times, minimizing downtime and operational costs for power plants and industrial facilities. The modular components can be replaced or serviced individually, which simplifies maintenance procedures and enhances overall reliability.

In terms of technology, the EGR3000 incorporates sophisticated materials and coatings that improve thermal resistance and durability. High-performance blades and combustion chambers are designed to withstand extreme temperatures, resulting in longer service life and reduced maintenance frequency. The engine also employs digital control systems that optimize performance parameters in real-time, ensuring peak efficiency under varying load conditions.

Emissions control is a critical aspect of the EGR3000's design. It features advanced combustion technology that minimizes NOx and CO2 emissions, aligning with stringent environmental regulations. The engine's design enables it to operate with lean-burn technology, further supporting reduced environmental impact.

Overall, the GE EGR3000 stands out as a powerful and efficient gas turbine solution. Its combination of high efficiency, fuel flexibility, modular design, and advanced emission control technologies makes it an ideal choice for various applications, including power generation and industrial processes. As energy demands continue to evolve, the EGR3000 positions itself as a reliable and forward-thinking solution for today’s energy landscape.
Top Page Image Contents