GE EGR3000 Installing the ANTI-TIP Device, When ALL Hookups are Completed

Page 43

Installation Instructions

9INSTALLING THE ANTI-TIP DEVICE

WARNING!

■Range must be secured with an approved Anti-Tip device.

■Unless properly installed, the range could be tipped by you or a child standing, sitting or leaning on an open door.

■After installing the Anti-Tip device, verify that it is in place by carefully attempting to tilt the range forward.

■This range has been designed to meet all recognized industry tip standards for all normal conditions.

■The use of this device does not preclude tipping of the range when not properly installed.

■If the Anti-Tip device supplied with the range does not fit this application, use the universal Anti-Tip device WB2X7909.

A.Mark the wall where the RIGHT EDGE of the range is to be located. Be sure to allow for the countertop overhang if you intend to install the range next to cabinets.

Anti-Tip

device

Slotted head

screw

Wallplate Approx. 20°

2 1⁄8” Marked edge of range

B. Locate the outside edge of the device 21⁄8 ″ toward the center of the range from the marked edge of the range.

C. Using the device as a template, mark the position of the hole for the screw.

D. For wood construction, drill a pilot hole at an angle of 20 degrees from the horizontal. A nail or awl may be used if a drill is not available.

Mount the Anti-Tip device with the screw provided.

For cement or concrete construction, you will need a 1/4″ x 11⁄2″ lag bolt and a 1/2″ O.D. sleeve anchor, which are not provided. Drill the recommended size hole for the hardware.

9INSTALLING THE ANTI-TIP DEVICE (CONT.)

Wallboard

Back of range

Anti-Tip device

Wood screw

Install the sleeve anchor into the drilled hole and then install the lag bolt through the device. The bolts must be properly tightened as recommended for the hardware.

E. Slide the range against the wall, and check for proper installation by grasping the front edge of the cooktop and carefully attempting to tilt the range forward.

WHEN ALL HOOKUPS ARE

COMPLETED

Make sure all controls are left in the off position. Make sure the flow of combustion and ventilation air to the range is unobstructed.

CONVERTING TO LP GAS (or converting back to natural gas from LP)

This range leaves the factory set for use with natural gas. If you want to convert to LP gas, the conversion must be performed by a qualified LP gas installer.

The conversion instructions and LP orifices can be found attached to the range next to the pressure regulator.

Keep these instructions and the orifices in case you want to convert back to natural gas.

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Write the model and serial numbers here Model # Serial # RangesSelf-Cleaning GasAll ranges can tip and injury could result ANTI-TIP DeviceImportant Safety Notice Instructions Surface Burners Cook Meat and Poultry THOROUGHLY… Instructions Operating Instructions SELF-CLEANING OvenConsumer Using the gas surface burnersInstructions Instructions OperatingCase of Power Failure SafetyTop-of-Range Cookware Consumer Support Troubleshooting Tips Using the oven controlsInstallation Instructions Oven Control, Clock and Timer Features and Settings Consumer Support Using the ovenAluminum Foil How to Set the Oven for Baking or RoastingPreheating and Pan Placement TipsBroiling Guide How to Set the Oven for BroilingHI Broil To Set the Clock Using the clock and timerInstallation To Set the TimerEnd of Cycle Tones on some models To Reset the TimerTo Cancel the Timer Touch the Kitchen Timer ON/OFFHow to Set a Delayed Start and Automatic Stop Using the timed baking and roasting featuresSafety Instructions Special features of your oven controlHour Shut-Off Designed for use on the Jewish Sabbath and Holidays Using the Sabbath Feature. on some modelsSafety Instructions How to Set for Regular Baking/RoastingHow to Exit the Sabbath Feature Type of margarine will affect baking performance Adjust the oven thermostat-Do it yourselfInstructions Troubleshooting Tips Consumer Support To Adjust the ThermostatBefore a Clean Cycle Using the self-cleaning ovenHow to Set the Oven for Cleaning Tips Consumer Support How to Delay the Start of CleaningTo Stop a Clean Cycle After a Clean CycleStandard Twin Burner Assemblies on some models Care and cleaning of the rangeSafety Burner heads After cleaningReplacement Burner capsTo Order Troubleshooting Tips Consumer SupportBurner Grates Cooktop SurfaceBroiler Pan and Grid Troubleshooting TipsLift-Off Oven Door Oven BottomRemovable Storage Drawer on some models Removable Kick Panel on some modelsLower Control Panel Front Manifold Panel and Knobs Oven Air VentsTo replace cover Oven Light ReplacementOven Shelves Do not remove any screws to remove the coverMaterials YOU MAY Need For Your SafetyPart Included Tools YOU will NeedInstallation Instructions Dimensions and Clearances Location ANTI-TIP DeviceProvide Adequate GAS Supply Connect the Range to GASInstallation Instructions Rigid Pipe Hookup Options Pressure regulator Manifold pipe Electrical Requirements Electrical ConnectionsSeal the Openings Check Ignition of Surface BurnersCheck Ignition of Oven Burner To remove the oven bottom Leveling the RangeWhen ALL Hookups are Completed Installing the ANTI-TIP DeviceProblem Possible Causes What To Do Before you call for service…Oven temperature See the Using the clock and timer sectionSee the Care and cleaning of the range section See the Installation of the range sectionOven door will not After a clean cycle Oven not clean afterClean cycle Excessive smokingStrong odor Power outageClock flashes Emitting from the ventOperating Instructions Safety Instructions We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Page Consumer Support Looking For Something More? AccessoriesWhat GE Will Not Cover Instructions Safety InstructionsOperating GE Will ReplaceWhat Camco Will Not Cover Camco Will ReplaceReal Life Design Studio Schedule ServiceParts and Accessories Consumer Support GE Appliances Website

EGR3000 specifications

The GE EGR3000 is a cutting-edge gas turbine engine designed to meet the demands of modern power generation and transportation applications. This innovative engine showcases a range of advanced features and technologies that enhance its performance, efficiency, and reliability.

One of the key characteristics of the EGR3000 is its exceptional efficiency. The engine employs an advanced thermodynamic cycle, which incorporates a high compression ratio and an innovative cooling design. This efficiency is particularly important in reducing fuel consumption and emissions, making it an environmentally friendly option compared to traditional gas turbines. The EGR3000 boasts a thermal efficiency rating that places it among the highest in its class.

The EGR3000 utilizes a dual-fuel capability, allowing it to operate on a variety of fuels. This flexibility is crucial for operators looking to optimize their fuel use based on availability and cost, adding to the engine's versatility. Additionally, the engine is designed to accommodate both natural gas and liquid fuels, thereby enhancing its operational range.

Another notable feature is the engine's advanced modular design. This allows for easier maintenance and quicker turnaround times, minimizing downtime and operational costs for power plants and industrial facilities. The modular components can be replaced or serviced individually, which simplifies maintenance procedures and enhances overall reliability.

In terms of technology, the EGR3000 incorporates sophisticated materials and coatings that improve thermal resistance and durability. High-performance blades and combustion chambers are designed to withstand extreme temperatures, resulting in longer service life and reduced maintenance frequency. The engine also employs digital control systems that optimize performance parameters in real-time, ensuring peak efficiency under varying load conditions.

Emissions control is a critical aspect of the EGR3000's design. It features advanced combustion technology that minimizes NOx and CO2 emissions, aligning with stringent environmental regulations. The engine's design enables it to operate with lean-burn technology, further supporting reduced environmental impact.

Overall, the GE EGR3000 stands out as a powerful and efficient gas turbine solution. Its combination of high efficiency, fuel flexibility, modular design, and advanced emission control technologies makes it an ideal choice for various applications, including power generation and industrial processes. As energy demands continue to evolve, the EGR3000 positions itself as a reliable and forward-thinking solution for today’s energy landscape.
Top Page Image Contents