GE EGR3000 Part Included, For Your Safety, Tools YOU will Need, Materials YOU MAY Need

Page 32

Installation Instructions

Range

If you have questions, call 1.800.GE.CARES or visit our Website at: www.GEAppliances.com

In the Commonwealth of Massachusetts:

•This product must be installed by a licensed plumber or gas fitter.

•When using ball-type gas shut-off valves, they shall be the T-handle type.

•A flexible gas connector, when used, must not exceed 3 feet.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

Installation of this range must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA.54, latest edition. In Canada, installation must conform with the current Natural Gas Installation Code, CAN/CGA-B149.1 or the current Propane Installation Code, CAN/CGA-B149.2, and with local codes where applicable. This range has been design-certified by CSA International according to ANSI Z21.1, latest edition and Canadian Gas Association according to CAN/CGA-1.1 latest edition.

As with any appliance using gas and generating heat, there are certain safety precautions you should follow. You will find these precautions in the Important Safety Information section in the front of this manual. Read them carefully.

•IMPORTANT – Save these instructions for local electrical inspector’s use.

•IMPORTANT – Observe all governing codes and ordinances.

•Note to Installer – Be sure to leave these instructions with the Consumer.

•Note to Consumer – Keep these instructions for future reference.

•Note – This appliance must be properly grounded.

•Servicer – The electrical diagram is in an envelope attached to the back of the range.

•Skill level – Installation of this appliance requires basic mechanical skills.

•Proper installation is the responsibility of the installer.

•Product failure due to improper installation is not covered under the Warranty.

PART INCLUDED

Anti-Tip bracket kit

32

FOR YOUR SAFETY

Do not store or use combustible materials, gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

If you smell gas:

Open windows.

Don’t touch electrical switches.

Extinguish any open flame.

Immediately call your gas supplier.

TOOLS YOU WILL NEED

Phillips screwdriver

 

Flat-blade screwdriver

Open-end or

adjustable wrench

 

Pencil and ruler

 

 

Level

Pipe wrenches (2)

 

(one for backup)

Drill, awl or nail

 

MATERIALS YOU MAY NEED

•Gas line shut-off valve

•Pipe joint sealant or UL-approved pipe thread tape with Teflon* that resists action of natural and LP gases

•Flexible metal appliance connector (1/2 ″ I.D.)

A 5-foot length is recommended for ease of installation but other lengths are acceptable. Never use an old connector when installing a new range.

•Flare union adapter for connection to gas supply line (3/4 ″ or 1/2 ″ NPT x 1/2 ″ I.D.)

•Flare union adapter for connection to pressure regulator on range (1/2 ″ NPT x 1/2 ″ I.D.)

•Liquid leak detector or soapy water.

•Lag bolt or 1/2″ O.D. sleeve anchor (for concrete floors only).

*Teflon: Registered trademark of DuPont

Page 31 Page 33
Image 32
Page 31 Page 33
Contents RangesSelf-Cleaning Gas Write the model and serial numbers here Model # Serial #ANTI-TIP Device All ranges can tip and injury could resultImportant Safety Notice Instructions Surface Burners Cook Meat and Poultry THOROUGHLY… SELF-CLEANING Oven Instructions Operating InstructionsUsing the gas surface burners InstructionsInstructions Operating ConsumerTop-of-Range Cookware SafetyCase of Power Failure Installation Instructions Using the oven controlsConsumer Support Troubleshooting Tips Oven Control, Clock and Timer Features and Settings Using the oven Consumer SupportHow to Set the Oven for Baking or Roasting Preheating and Pan PlacementTips Aluminum FoilHI Broil How to Set the Oven for BroilingBroiling Guide Using the clock and timer InstallationTo Set the Timer To Set the ClockTo Reset the Timer To Cancel the TimerTouch the Kitchen Timer ON/OFF End of Cycle Tones on some modelsUsing the timed baking and roasting features How to Set a Delayed Start and Automatic StopHour Shut-Off Special features of your oven controlSafety Instructions Using the Sabbath Feature. on some models Safety InstructionsHow to Set for Regular Baking/Roasting Designed for use on the Jewish Sabbath and HolidaysHow to Exit the Sabbath Feature Adjust the oven thermostat-Do it yourself Instructions Troubleshooting Tips Consumer SupportTo Adjust the Thermostat Type of margarine will affect baking performanceHow to Set the Oven for Cleaning Using the self-cleaning ovenBefore a Clean Cycle How to Delay the Start of Cleaning To Stop a Clean CycleAfter a Clean Cycle Tips Consumer SupportCare and cleaning of the range Standard Twin Burner Assemblies on some modelsSafety After cleaning ReplacementBurner caps Burner headsTroubleshooting Tips Consumer Support Burner GratesCooktop Surface To OrderTroubleshooting Tips Lift-Off Oven DoorOven Bottom Broiler Pan and GridRemovable Kick Panel on some models Removable Storage Drawer on some modelsOven Air Vents Lower Control Panel Front Manifold Panel and KnobsOven Light Replacement Oven ShelvesDo not remove any screws to remove the cover To replace coverFor Your Safety Part IncludedTools YOU will Need Materials YOU MAY NeedInstallation Instructions Dimensions and Clearances ANTI-TIP Device LocationConnect the Range to GAS Provide Adequate GAS SupplyInstallation Instructions Rigid Pipe Hookup Options Pressure regulator Manifold pipe Electrical Connections Electrical RequirementsCheck Ignition of Oven Burner Check Ignition of Surface BurnersSeal the Openings Leveling the Range To remove the oven bottomInstalling the ANTI-TIP Device When ALL Hookups are CompletedBefore you call for service… Problem Possible Causes What To DoSee the Using the clock and timer section See the Care and cleaning of the range sectionSee the Installation of the range section Oven temperatureAfter a clean cycle Oven not clean after Clean cycleExcessive smoking Oven door will notPower outage Clock flashesEmitting from the vent Strong odorOperating Instructions Safety Instructions We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Page Consumer Support Accessories Looking For Something More?Instructions Safety Instructions OperatingGE Will Replace What GE Will Not CoverCamco Will Replace What Camco Will Not CoverSchedule Service Parts and AccessoriesConsumer Support GE Appliances Website Real Life Design Studio

EGR3000 specifications

The GE EGR3000 is a cutting-edge gas turbine engine designed to meet the demands of modern power generation and transportation applications. This innovative engine showcases a range of advanced features and technologies that enhance its performance, efficiency, and reliability.

One of the key characteristics of the EGR3000 is its exceptional efficiency. The engine employs an advanced thermodynamic cycle, which incorporates a high compression ratio and an innovative cooling design. This efficiency is particularly important in reducing fuel consumption and emissions, making it an environmentally friendly option compared to traditional gas turbines. The EGR3000 boasts a thermal efficiency rating that places it among the highest in its class.

The EGR3000 utilizes a dual-fuel capability, allowing it to operate on a variety of fuels. This flexibility is crucial for operators looking to optimize their fuel use based on availability and cost, adding to the engine's versatility. Additionally, the engine is designed to accommodate both natural gas and liquid fuels, thereby enhancing its operational range.

Another notable feature is the engine's advanced modular design. This allows for easier maintenance and quicker turnaround times, minimizing downtime and operational costs for power plants and industrial facilities. The modular components can be replaced or serviced individually, which simplifies maintenance procedures and enhances overall reliability.

In terms of technology, the EGR3000 incorporates sophisticated materials and coatings that improve thermal resistance and durability. High-performance blades and combustion chambers are designed to withstand extreme temperatures, resulting in longer service life and reduced maintenance frequency. The engine also employs digital control systems that optimize performance parameters in real-time, ensuring peak efficiency under varying load conditions.

Emissions control is a critical aspect of the EGR3000's design. It features advanced combustion technology that minimizes NOx and CO2 emissions, aligning with stringent environmental regulations. The engine's design enables it to operate with lean-burn technology, further supporting reduced environmental impact.

Overall, the GE EGR3000 stands out as a powerful and efficient gas turbine solution. Its combination of high efficiency, fuel flexibility, modular design, and advanced emission control technologies makes it an ideal choice for various applications, including power generation and industrial processes. As energy demands continue to evolve, the EGR3000 positions itself as a reliable and forward-thinking solution for today’s energy landscape.
Top Page Image Contents