GE EGR3000 Oven Air Vents, Lower Control Panel Front Manifold Panel and Knobs

Page 30

Care and cleaning of the range.

Oven Air Vents

Never block the vents (air openings) of the range. They provide the air inlet and outlet that are necessary for the range to operate properly with correct combustion.

Vent appearance and location vary.

Air openings are located at the rear of the cooktop, at the top and bottom of the oven door, and at the bottom of the range, under the storage drawer or kick panel (depending on the model).

Lower Control Panel (Front Manifold Panel) and Knobs

Consumer Support Troubleshooting Tips Installation Instructions Operating Instructions Safety Instructions

Pull the knob straight off the stem.

It’s a good idea to wipe the control panel after each use of the oven. Use a damp cloth to clean or rinse. For cleaning, use mild soap and water or a 50/50 solution of vinegar and water. For rinsing, use clean water. Polish dry with a soft cloth.

Do not use abrasive cleansers, strong liquid cleaners, plastic scouring pads or oven cleaners on the control panel—they will damage the finish.

Do not bend knobs by pulling them up or down or by hanging a towel or other such loads. This can damage the gas valve shaft.

The control knobs may be removed for easier cleaning. To remove a knob, pull it straight off the stem. If knob is difficult to remove, place a towel or dishcloth between the knob and control panel and pull gently. Wash the knobs in soap and water or a vinegar and hot water solution.

Metal parts can be cleaned with soap and water. Do not use steel wool, abrasives, ammonia, acids or commercial oven cleaners. Dry with a soft cloth.

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents RangesSelf-Cleaning Gas Write the model and serial numbers here Model # Serial #ANTI-TIP Device All ranges can tip and injury could resultImportant Safety Notice Instructions Surface Burners Cook Meat and Poultry THOROUGHLY… SELF-CLEANING Oven Instructions Operating InstructionsInstructions Operating Using the gas surface burnersInstructions ConsumerSafety Case of Power FailureTop-of-Range Cookware Using the oven controls Consumer Support Troubleshooting TipsInstallation Instructions Oven Control, Clock and Timer Features and Settings Using the oven Consumer SupportTips How to Set the Oven for Baking or RoastingPreheating and Pan Placement Aluminum FoilHow to Set the Oven for Broiling Broiling GuideHI Broil To Set the Timer Using the clock and timerInstallation To Set the ClockTouch the Kitchen Timer ON/OFF To Reset the TimerTo Cancel the Timer End of Cycle Tones on some modelsUsing the timed baking and roasting features How to Set a Delayed Start and Automatic StopSpecial features of your oven control Safety InstructionsHour Shut-Off How to Set for Regular Baking/Roasting Using the Sabbath Feature. on some modelsSafety Instructions Designed for use on the Jewish Sabbath and HolidaysHow to Exit the Sabbath Feature To Adjust the Thermostat Adjust the oven thermostat-Do it yourselfInstructions Troubleshooting Tips Consumer Support Type of margarine will affect baking performanceUsing the self-cleaning oven Before a Clean CycleHow to Set the Oven for Cleaning After a Clean Cycle How to Delay the Start of CleaningTo Stop a Clean Cycle Tips Consumer SupportCare and cleaning of the range Standard Twin Burner Assemblies on some modelsSafety Burner caps After cleaningReplacement Burner headsCooktop Surface Troubleshooting Tips Consumer SupportBurner Grates To OrderOven Bottom Troubleshooting TipsLift-Off Oven Door Broiler Pan and GridRemovable Kick Panel on some models Removable Storage Drawer on some modelsOven Air Vents Lower Control Panel Front Manifold Panel and KnobsDo not remove any screws to remove the cover Oven Light ReplacementOven Shelves To replace coverTools YOU will Need For Your SafetyPart Included Materials YOU MAY NeedInstallation Instructions Dimensions and Clearances ANTI-TIP Device LocationConnect the Range to GAS Provide Adequate GAS SupplyInstallation Instructions Rigid Pipe Hookup Options Pressure regulator Manifold pipe Electrical Connections Electrical RequirementsCheck Ignition of Surface Burners Seal the OpeningsCheck Ignition of Oven Burner Leveling the Range To remove the oven bottomInstalling the ANTI-TIP Device When ALL Hookups are CompletedBefore you call for service… Problem Possible Causes What To DoSee the Installation of the range section See the Using the clock and timer sectionSee the Care and cleaning of the range section Oven temperatureExcessive smoking After a clean cycle Oven not clean afterClean cycle Oven door will notEmitting from the vent Power outageClock flashes Strong odorOperating Instructions Safety Instructions We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Page Consumer Support Accessories Looking For Something More?GE Will Replace Instructions Safety InstructionsOperating What GE Will Not CoverCamco Will Replace What Camco Will Not CoverConsumer Support GE Appliances Website Schedule ServiceParts and Accessories Real Life Design Studio

EGR3000 specifications

The GE EGR3000 is a cutting-edge gas turbine engine designed to meet the demands of modern power generation and transportation applications. This innovative engine showcases a range of advanced features and technologies that enhance its performance, efficiency, and reliability.

One of the key characteristics of the EGR3000 is its exceptional efficiency. The engine employs an advanced thermodynamic cycle, which incorporates a high compression ratio and an innovative cooling design. This efficiency is particularly important in reducing fuel consumption and emissions, making it an environmentally friendly option compared to traditional gas turbines. The EGR3000 boasts a thermal efficiency rating that places it among the highest in its class.

The EGR3000 utilizes a dual-fuel capability, allowing it to operate on a variety of fuels. This flexibility is crucial for operators looking to optimize their fuel use based on availability and cost, adding to the engine's versatility. Additionally, the engine is designed to accommodate both natural gas and liquid fuels, thereby enhancing its operational range.

Another notable feature is the engine's advanced modular design. This allows for easier maintenance and quicker turnaround times, minimizing downtime and operational costs for power plants and industrial facilities. The modular components can be replaced or serviced individually, which simplifies maintenance procedures and enhances overall reliability.

In terms of technology, the EGR3000 incorporates sophisticated materials and coatings that improve thermal resistance and durability. High-performance blades and combustion chambers are designed to withstand extreme temperatures, resulting in longer service life and reduced maintenance frequency. The engine also employs digital control systems that optimize performance parameters in real-time, ensuring peak efficiency under varying load conditions.

Emissions control is a critical aspect of the EGR3000's design. It features advanced combustion technology that minimizes NOx and CO2 emissions, aligning with stringent environmental regulations. The engine's design enables it to operate with lean-burn technology, further supporting reduced environmental impact.

Overall, the GE EGR3000 stands out as a powerful and efficient gas turbine solution. Its combination of high efficiency, fuel flexibility, modular design, and advanced emission control technologies makes it an ideal choice for various applications, including power generation and industrial processes. As energy demands continue to evolve, the EGR3000 positions itself as a reliable and forward-thinking solution for today’s energy landscape.
Top Page Image Contents