GE EGR3000 Tips Consumer Support, How to Delay the Start of Cleaning, To Stop a Clean Cycle

Page 23

www.GEAppliances.com

The oven door must be closed and all controls set correctly for the cycle to work properly.

Safety

How to Delay the Start of Cleaning

You can set the oven control to delay-start the oven, clean for a specific length of time and then turn off automatically.

Make sure the clock shows the correct time of day.

Follow the directions in the Before a Clean Cycle section.

Latch the door.

NOTE: Never force the latch. If the oven is too hot, you will not be able to slide the latch. Allow the oven to cool.

Touch the SELF CLEAN pad.

Touch the + or – pads to set the

Clean Time.

The Clean Time is preset for 4 hours and 20 minutes. You can change the Clean Time to any time between 3 and 5 hours, depending on the amount of soil in your oven. If a different Clean Time is desired, touch the + or – pads until the desired Clean Time is displayed.

Touch the START TIME pad.

Change the Start Time by touching the + or – pads. The start time will appear in the display.

Touch the START/ON pad.

The self-clean cycle will automatically begin at the time set.

While the oven is self-cleaning, you can touch the CLOCK pad to display the time of day. To return to the clean countdown, touch the SELF CLEAN pad.

The oven shuts off automatically when the clean cycle is complete, and 0:00 will flash in the display.

Slide the latch handle to the left as far as it will go and open the door.

Instructions Operating Instructions Installation

To Stop a Clean Cycle

Touch the CLEAR/OFF pad.

Wait until the oven has cooled below the locking temperature to unlatch the door. You will not be able to open the door right away unless the oven has cooled below the locking temperature.

Instructions Troubleshooting

After a Clean Cycle

You cannot set the oven for cooking until the oven is cool enough for the door to be unlatched.

You may notice some white ash in the oven. Wipe it up with a damp cloth after the oven cools.

If white spots remain, remove them with a soap- filled scouring pad and rinse thoroughly with

a vinegar and water mixture.

These deposits are usually a salt residue that cannot be removed by the clean cycle.

If the oven is not clean after one clean cycle, repeat the cycle.

■You cannot set the oven for cooking until the oven is cool enough for the door

to unlock.

■While the oven is self-cleaning, you can touch the CLOCK pad to display the time of day. To return to the clean countdown, touch the COOKING TIME pad.

■If the shelves become hard to slide, apply a small amount of vegetable oil or cooking oil to a paper towel and wipe the edges of the oven shelves with the paper towel.

Tips Consumer Support

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Write the model and serial numbers here Model # Serial # RangesSelf-Cleaning GasAll ranges can tip and injury could result ANTI-TIP DeviceImportant Safety Notice Instructions Surface Burners Cook Meat and Poultry THOROUGHLY… Instructions Operating Instructions SELF-CLEANING OvenConsumer Using the gas surface burnersInstructions Instructions OperatingTop-of-Range Cookware SafetyCase of Power Failure Installation Instructions Using the oven controlsConsumer Support Troubleshooting Tips Oven Control, Clock and Timer Features and Settings Consumer Support Using the ovenAluminum Foil How to Set the Oven for Baking or RoastingPreheating and Pan Placement TipsHI Broil How to Set the Oven for BroilingBroiling Guide To Set the Clock Using the clock and timerInstallation To Set the TimerEnd of Cycle Tones on some models To Reset the TimerTo Cancel the Timer Touch the Kitchen Timer ON/OFFHow to Set a Delayed Start and Automatic Stop Using the timed baking and roasting featuresHour Shut-Off Special features of your oven controlSafety Instructions Designed for use on the Jewish Sabbath and Holidays Using the Sabbath Feature. on some modelsSafety Instructions How to Set for Regular Baking/RoastingHow to Exit the Sabbath Feature Type of margarine will affect baking performance Adjust the oven thermostat-Do it yourselfInstructions Troubleshooting Tips Consumer Support To Adjust the ThermostatHow to Set the Oven for Cleaning Using the self-cleaning ovenBefore a Clean Cycle Tips Consumer Support How to Delay the Start of CleaningTo Stop a Clean Cycle After a Clean CycleStandard Twin Burner Assemblies on some models Care and cleaning of the rangeSafety Burner heads After cleaningReplacement Burner capsTo Order Troubleshooting Tips Consumer SupportBurner Grates Cooktop SurfaceBroiler Pan and Grid Troubleshooting TipsLift-Off Oven Door Oven BottomRemovable Storage Drawer on some models Removable Kick Panel on some modelsLower Control Panel Front Manifold Panel and Knobs Oven Air VentsTo replace cover Oven Light ReplacementOven Shelves Do not remove any screws to remove the coverMaterials YOU MAY Need For Your SafetyPart Included Tools YOU will NeedInstallation Instructions Dimensions and Clearances Location ANTI-TIP DeviceProvide Adequate GAS Supply Connect the Range to GASInstallation Instructions Rigid Pipe Hookup Options Pressure regulator Manifold pipe Electrical Requirements Electrical ConnectionsCheck Ignition of Oven Burner Check Ignition of Surface BurnersSeal the Openings To remove the oven bottom Leveling the RangeWhen ALL Hookups are Completed Installing the ANTI-TIP DeviceProblem Possible Causes What To Do Before you call for service…Oven temperature See the Using the clock and timer sectionSee the Care and cleaning of the range section See the Installation of the range sectionOven door will not After a clean cycle Oven not clean afterClean cycle Excessive smokingStrong odor Power outageClock flashes Emitting from the ventOperating Instructions Safety Instructions We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Page Consumer Support Looking For Something More? AccessoriesWhat GE Will Not Cover Instructions Safety InstructionsOperating GE Will ReplaceWhat Camco Will Not Cover Camco Will ReplaceReal Life Design Studio Schedule ServiceParts and Accessories Consumer Support GE Appliances Website

EGR3000 specifications

The GE EGR3000 is a cutting-edge gas turbine engine designed to meet the demands of modern power generation and transportation applications. This innovative engine showcases a range of advanced features and technologies that enhance its performance, efficiency, and reliability.

One of the key characteristics of the EGR3000 is its exceptional efficiency. The engine employs an advanced thermodynamic cycle, which incorporates a high compression ratio and an innovative cooling design. This efficiency is particularly important in reducing fuel consumption and emissions, making it an environmentally friendly option compared to traditional gas turbines. The EGR3000 boasts a thermal efficiency rating that places it among the highest in its class.

The EGR3000 utilizes a dual-fuel capability, allowing it to operate on a variety of fuels. This flexibility is crucial for operators looking to optimize their fuel use based on availability and cost, adding to the engine's versatility. Additionally, the engine is designed to accommodate both natural gas and liquid fuels, thereby enhancing its operational range.

Another notable feature is the engine's advanced modular design. This allows for easier maintenance and quicker turnaround times, minimizing downtime and operational costs for power plants and industrial facilities. The modular components can be replaced or serviced individually, which simplifies maintenance procedures and enhances overall reliability.

In terms of technology, the EGR3000 incorporates sophisticated materials and coatings that improve thermal resistance and durability. High-performance blades and combustion chambers are designed to withstand extreme temperatures, resulting in longer service life and reduced maintenance frequency. The engine also employs digital control systems that optimize performance parameters in real-time, ensuring peak efficiency under varying load conditions.

Emissions control is a critical aspect of the EGR3000's design. It features advanced combustion technology that minimizes NOx and CO2 emissions, aligning with stringent environmental regulations. The engine's design enables it to operate with lean-burn technology, further supporting reduced environmental impact.

Overall, the GE EGR3000 stands out as a powerful and efficient gas turbine solution. Its combination of high efficiency, fuel flexibility, modular design, and advanced emission control technologies makes it an ideal choice for various applications, including power generation and industrial processes. As energy demands continue to evolve, the EGR3000 positions itself as a reliable and forward-thinking solution for today’s energy landscape.
Top Page Image Contents