GE EGR3000 installation instructions ANTI-TIP Device, Location

Page 35

Installation Instructions

WARNING!

ANTI-TIP DEVICE

All ranges can tip and injury could result.

To prevent accidental tipping of the range, attach an approved Anti-Tip device to the wall. (See Installing the Anti-Tip Device in this section.) To check if the device is installed and engaged properly, carefully tip the range forward. The Anti-Tip device should engage and prevent the range from tipping over.

If you pull the range out from the wall for any reason, make sure the Anti-Tip device is engaged when you push the range back against the wall.

■For your safety, never use your range for warming or heating the room. Your oven and cooktop are not designed to heat your kitchen. Top burners should not be operated without cookware on the grate. Such abuse could result in fire and damage to your range and will void your warranty.

■Do not store or use combustible materials, gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Explosions or fires could result.

■Do not use oven for a storage area. Items stored in the oven can ignite.

■Do not let cooking grease or other flammable materials accumulate in or near the range.

LOCATION

Do not locate the range where it may be subject to strong drafts. Any openings in the floor or wall behind the range should be sealed. Make sure the openings around the base of the range that supply fresh air for combustion and ventilation are not obstructed by carpeting or woodwork.

Your range, like many other household items, is heavy and can settle into soft floor coverings such as cushioned vinyl or carpeting. Use care when moving the range

on this type of flooring. It is recommended that the following simple and inexpensive instructions be followed to protect your floor.

The range should be installed on a sheet of plywood (or similar material). When the floor covering ends at the front of the range, the area that the range will rest on should be built up with plywood to the same level or higher than the floor covering.

This will allow the range to be moved for cleaning or servicing. Also, make sure your floor covering will withstand 180°F. (See the Installation Safety Instructions section.)

Make sure the wall coverings around your range can withstand the heat generated (up to 200°F) by the range. (See the Installation Safety Instructions section.)

IMPORTANT!

Remove all tape and packaging. Make sure the burners are properly seated and level.

Lift up the cooktop (on models with standard twin burners) and remove any packing material under it.

Take the accessory pack out of the oven and/or drawer.

Check to be sure that no range parts have come loose during shipping.

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Write the model and serial numbers here Model # Serial # RangesSelf-Cleaning GasAll ranges can tip and injury could result ANTI-TIP DeviceImportant Safety Notice Instructions Surface Burners Cook Meat and Poultry THOROUGHLY… Instructions Operating Instructions SELF-CLEANING OvenConsumer Using the gas surface burnersInstructions Instructions OperatingTop-of-Range Cookware SafetyCase of Power Failure Installation Instructions Using the oven controlsConsumer Support Troubleshooting Tips Oven Control, Clock and Timer Features and Settings Consumer Support Using the ovenAluminum Foil How to Set the Oven for Baking or RoastingPreheating and Pan Placement TipsHI Broil How to Set the Oven for BroilingBroiling Guide To Set the Clock Using the clock and timerInstallation To Set the TimerEnd of Cycle Tones on some models To Reset the TimerTo Cancel the Timer Touch the Kitchen Timer ON/OFFHow to Set a Delayed Start and Automatic Stop Using the timed baking and roasting featuresHour Shut-Off Special features of your oven controlSafety Instructions Designed for use on the Jewish Sabbath and Holidays Using the Sabbath Feature. on some modelsSafety Instructions How to Set for Regular Baking/RoastingHow to Exit the Sabbath Feature Type of margarine will affect baking performance Adjust the oven thermostat-Do it yourselfInstructions Troubleshooting Tips Consumer Support To Adjust the ThermostatHow to Set the Oven for Cleaning Using the self-cleaning ovenBefore a Clean Cycle Tips Consumer Support How to Delay the Start of CleaningTo Stop a Clean Cycle After a Clean CycleStandard Twin Burner Assemblies on some models Care and cleaning of the rangeSafety Burner heads After cleaningReplacement Burner capsTo Order Troubleshooting Tips Consumer SupportBurner Grates Cooktop SurfaceBroiler Pan and Grid Troubleshooting TipsLift-Off Oven Door Oven BottomRemovable Storage Drawer on some models Removable Kick Panel on some modelsLower Control Panel Front Manifold Panel and Knobs Oven Air VentsTo replace cover Oven Light ReplacementOven Shelves Do not remove any screws to remove the coverMaterials YOU MAY Need For Your SafetyPart Included Tools YOU will NeedInstallation Instructions Dimensions and Clearances Location ANTI-TIP DeviceProvide Adequate GAS Supply Connect the Range to GASInstallation Instructions Rigid Pipe Hookup Options Pressure regulator Manifold pipe Electrical Requirements Electrical ConnectionsCheck Ignition of Oven Burner Check Ignition of Surface BurnersSeal the Openings To remove the oven bottom Leveling the RangeWhen ALL Hookups are Completed Installing the ANTI-TIP DeviceProblem Possible Causes What To Do Before you call for service…Oven temperature See the Using the clock and timer sectionSee the Care and cleaning of the range section See the Installation of the range sectionOven door will not After a clean cycle Oven not clean afterClean cycle Excessive smokingStrong odor Power outageClock flashes Emitting from the ventOperating Instructions Safety Instructions We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Page Consumer Support Looking For Something More? AccessoriesWhat GE Will Not Cover Instructions Safety InstructionsOperating GE Will ReplaceWhat Camco Will Not Cover Camco Will ReplaceReal Life Design Studio Schedule ServiceParts and Accessories Consumer Support GE Appliances Website

EGR3000 specifications

The GE EGR3000 is a cutting-edge gas turbine engine designed to meet the demands of modern power generation and transportation applications. This innovative engine showcases a range of advanced features and technologies that enhance its performance, efficiency, and reliability.

One of the key characteristics of the EGR3000 is its exceptional efficiency. The engine employs an advanced thermodynamic cycle, which incorporates a high compression ratio and an innovative cooling design. This efficiency is particularly important in reducing fuel consumption and emissions, making it an environmentally friendly option compared to traditional gas turbines. The EGR3000 boasts a thermal efficiency rating that places it among the highest in its class.

The EGR3000 utilizes a dual-fuel capability, allowing it to operate on a variety of fuels. This flexibility is crucial for operators looking to optimize their fuel use based on availability and cost, adding to the engine's versatility. Additionally, the engine is designed to accommodate both natural gas and liquid fuels, thereby enhancing its operational range.

Another notable feature is the engine's advanced modular design. This allows for easier maintenance and quicker turnaround times, minimizing downtime and operational costs for power plants and industrial facilities. The modular components can be replaced or serviced individually, which simplifies maintenance procedures and enhances overall reliability.

In terms of technology, the EGR3000 incorporates sophisticated materials and coatings that improve thermal resistance and durability. High-performance blades and combustion chambers are designed to withstand extreme temperatures, resulting in longer service life and reduced maintenance frequency. The engine also employs digital control systems that optimize performance parameters in real-time, ensuring peak efficiency under varying load conditions.

Emissions control is a critical aspect of the EGR3000's design. It features advanced combustion technology that minimizes NOx and CO2 emissions, aligning with stringent environmental regulations. The engine's design enables it to operate with lean-burn technology, further supporting reduced environmental impact.

Overall, the GE EGR3000 stands out as a powerful and efficient gas turbine solution. Its combination of high efficiency, fuel flexibility, modular design, and advanced emission control technologies makes it an ideal choice for various applications, including power generation and industrial processes. As energy demands continue to evolve, the EGR3000 positions itself as a reliable and forward-thinking solution for today’s energy landscape.
Top Page Image Contents