GE EGR3000 installation instructions Leveling the Range, To remove the oven bottom

Page 42

Installation Instructions

7ADJUST BROIL AND OVEN BURNER AIR ADJUSTMENT SHUTTERS IF NECESSARY

Air adjustment shutters for the top and bottom burners regulate the flow of air to the flames.

Air

adjustment shutter

Loosen

The air adjustment shutter for the top (broil) burner is in the center of the rear wall of the oven.

Loosen

Air adjustment shutter

The shutter for the bottom (oven) burner is near the back wall behind the storage drawer or kick panel. Remove the drawer or panel. See the Care and cleaning of the range section.

To adjust the flow of air to either burner, loosen the Phillips head screw and rotate the shutter toward open or closed position as needed.

The flames for the top (broil) burner should be steady with approximately 1″ blue cones and should not extend out over the edges of the burner baffle.

To determine if the bottom burner flames are burning properly, remove the oven bottom. Flames should have approximately 1″ blue cones and, if range is supplied with natural gas, should burn with no yellow tipping. (With most LP gas, small yellow tips at the end of outer cones are normal.) Flames should not lift off burner ports. If lifting is observed, gradually reduce air shutter opening until flames are stabilized.

7ADJUST BROIL AND OVEN BURNER AIR ADJUSTMENT SHUTTERS IF NECESSARY (CONT.)

Oven bottom

To remove the oven bottom:

A. Remove the knurled screws holding down rear of the oven bottom.

B. Grasp the oven bottom at finger slots on each side.

C. Lift the rear of the oven bottom enough to clear the lip of the range frame, push it back, and then pull it up and out.

8LEVELING THE RANGE

A.Install the oven shelves in the oven and position the range where it will be installed.

 

Raise

 

 

range

Lower

 

 

Lower

 

range

range

 

 

Leg leveler

Raise range

(on some models)

(on some models)

B. Check for levelness by placing a spirit level or a cup, partially filled with water, on one of the oven shelves. If using a spirit level, take two readings—with the level placed diagonally first in one direction and then

the other.

C. Remove the storage drawer or kick panel. See the Care and cleaning of the range section. The front leveling legs can be adjusted from the bottom and the rear legs can be adjusted from the top or the bottom.

D. Use an open-end or adjustable wrench to adjust the leveling legs until the range is level.

E. After the range is level, slide the range away from the wall so that the Anti-Tip device can be installed.

42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents RangesSelf-Cleaning Gas Write the model and serial numbers here Model # Serial #ANTI-TIP Device All ranges can tip and injury could resultImportant Safety Notice Instructions Surface Burners Cook Meat and Poultry THOROUGHLY… SELF-CLEANING Oven Instructions Operating InstructionsInstructions Operating Using the gas surface burnersInstructions ConsumerSafety Case of Power FailureTop-of-Range Cookware Using the oven controls Consumer Support Troubleshooting TipsInstallation Instructions Oven Control, Clock and Timer Features and Settings Using the oven Consumer SupportTips How to Set the Oven for Baking or RoastingPreheating and Pan Placement Aluminum FoilHow to Set the Oven for Broiling Broiling GuideHI Broil To Set the Timer Using the clock and timerInstallation To Set the ClockTouch the Kitchen Timer ON/OFF To Reset the TimerTo Cancel the Timer End of Cycle Tones on some modelsUsing the timed baking and roasting features How to Set a Delayed Start and Automatic StopSpecial features of your oven control Safety InstructionsHour Shut-Off How to Set for Regular Baking/Roasting Using the Sabbath Feature. on some modelsSafety Instructions Designed for use on the Jewish Sabbath and HolidaysHow to Exit the Sabbath Feature To Adjust the Thermostat Adjust the oven thermostat-Do it yourselfInstructions Troubleshooting Tips Consumer Support Type of margarine will affect baking performanceUsing the self-cleaning oven Before a Clean CycleHow to Set the Oven for Cleaning After a Clean Cycle How to Delay the Start of CleaningTo Stop a Clean Cycle Tips Consumer SupportCare and cleaning of the range Standard Twin Burner Assemblies on some modelsSafety Burner caps After cleaningReplacement Burner headsCooktop Surface Troubleshooting Tips Consumer SupportBurner Grates To OrderOven Bottom Troubleshooting TipsLift-Off Oven Door Broiler Pan and GridRemovable Kick Panel on some models Removable Storage Drawer on some modelsOven Air Vents Lower Control Panel Front Manifold Panel and KnobsDo not remove any screws to remove the cover Oven Light ReplacementOven Shelves To replace coverTools YOU will Need For Your SafetyPart Included Materials YOU MAY NeedInstallation Instructions Dimensions and Clearances ANTI-TIP Device LocationConnect the Range to GAS Provide Adequate GAS SupplyInstallation Instructions Rigid Pipe Hookup Options Pressure regulator Manifold pipe Electrical Connections Electrical RequirementsCheck Ignition of Surface Burners Seal the OpeningsCheck Ignition of Oven Burner Leveling the Range To remove the oven bottomInstalling the ANTI-TIP Device When ALL Hookups are CompletedBefore you call for service… Problem Possible Causes What To DoSee the Installation of the range section See the Using the clock and timer sectionSee the Care and cleaning of the range section Oven temperatureExcessive smoking After a clean cycle Oven not clean afterClean cycle Oven door will notEmitting from the vent Power outageClock flashes Strong odorOperating Instructions Safety Instructions We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Page Consumer Support Accessories Looking For Something More?GE Will Replace Instructions Safety InstructionsOperating What GE Will Not CoverCamco Will Replace What Camco Will Not CoverConsumer Support GE Appliances Website Schedule ServiceParts and Accessories Real Life Design Studio

EGR3000 specifications

The GE EGR3000 is a cutting-edge gas turbine engine designed to meet the demands of modern power generation and transportation applications. This innovative engine showcases a range of advanced features and technologies that enhance its performance, efficiency, and reliability.

One of the key characteristics of the EGR3000 is its exceptional efficiency. The engine employs an advanced thermodynamic cycle, which incorporates a high compression ratio and an innovative cooling design. This efficiency is particularly important in reducing fuel consumption and emissions, making it an environmentally friendly option compared to traditional gas turbines. The EGR3000 boasts a thermal efficiency rating that places it among the highest in its class.

The EGR3000 utilizes a dual-fuel capability, allowing it to operate on a variety of fuels. This flexibility is crucial for operators looking to optimize their fuel use based on availability and cost, adding to the engine's versatility. Additionally, the engine is designed to accommodate both natural gas and liquid fuels, thereby enhancing its operational range.

Another notable feature is the engine's advanced modular design. This allows for easier maintenance and quicker turnaround times, minimizing downtime and operational costs for power plants and industrial facilities. The modular components can be replaced or serviced individually, which simplifies maintenance procedures and enhances overall reliability.

In terms of technology, the EGR3000 incorporates sophisticated materials and coatings that improve thermal resistance and durability. High-performance blades and combustion chambers are designed to withstand extreme temperatures, resulting in longer service life and reduced maintenance frequency. The engine also employs digital control systems that optimize performance parameters in real-time, ensuring peak efficiency under varying load conditions.

Emissions control is a critical aspect of the EGR3000's design. It features advanced combustion technology that minimizes NOx and CO2 emissions, aligning with stringent environmental regulations. The engine's design enables it to operate with lean-burn technology, further supporting reduced environmental impact.

Overall, the GE EGR3000 stands out as a powerful and efficient gas turbine solution. Its combination of high efficiency, fuel flexibility, modular design, and advanced emission control technologies makes it an ideal choice for various applications, including power generation and industrial processes. As energy demands continue to evolve, the EGR3000 positions itself as a reliable and forward-thinking solution for today’s energy landscape.
Top Page Image Contents