GE J2B915 Using the self-cleaning oven, Before a Clean Cycle, How to Set the Oven for Cleaning

Page 29

Using the self-cleaning oven.

www.GEAppliances.com

The oven door must be closed and all controls set correctly for the cycle to work properly.

Safety

Wipe up heavy soil on the oven bottom.

Before a Clean Cycle

For the first self-clean cycle, we recommend venting your kitchen with an open window or using a ventilation fan or hood.

Remove the shelves, broiler pan, broiler grid, probe, all cookware and any aluminum foil from the oven.

The oven shelves can be self-cleaned, but they will darken, lose their luster and become hard to slide.

Soil on the front frame of the range and outside the gasket on the door will need to be cleaned by hand. Clean these areas with hot water, soap-filled scouring pads or cleansers such as Soft Scrub®. Rinse well with clean water and dry.

Do not clean the gasket. The fiberglass material of the oven door gasket cannot withstand abrasion. It is essential for the gasket to remain intact. If you notice it becoming worn or frayed, replace it.

Wipe up any heavy spillovers on the oven bottom.

Make sure the oven light bulb cover is in place and the oven light is off.

IMPORTANT: The health of some birds is extremely sensitive to the fumes given off during the self-cleaning cycle of any range. Move birds to another well-ventilated room.

Instructions Operating Instructions

How to Set the Oven for Cleaning

Touch the SELF CLEAN pad.

Using the number pads, enter the desired clean time, if a time other than 4 hours is needed.

Clean cycle time is normally 4 hours.

You can change the clean time to any time between 3 hours and 5 hours, depending on how dirty your oven is.

Touch the START pad.

The door locks automatically. The display will show the clean time remaining. It will not be possible to open the oven door until the temperature drops below the lock temperature and the LOCKED DOOR light goes off.

When the LOCKED DOOR light is off, open the door.

The oven shuts off automatically when the clean cycle is complete.

The words LOCK DOOR will flash and the oven control will signal if you set the clean cycle and forget to close the oven door.

To stop a clean cycle, touch the

CLEAR/OFF pad. When the LOCKED DOOR light goes off indicating the oven has cooled below the locking temperature, open the door.

Do not use the warming drawer during a self-clean cycle.

Installation Instructions Troubleshooting Tips Consumer Support

29

Image 29
Contents Write the model and serial numbers here Model # Serial # Installation InstructionsANTI-TIP Device Install ANTI-TIP Devices Packed with RangeAll ranges can tip and injury could result Safety Precautions Important Safety NoticeSafety Surface Burners Safety InstructionsElectric Warming Drawer Instructions Safety Instructions SELF-CLEANING OvenSupport Troubleshooting Tips Cook Meat and Poultry THOROUGHLY…Instructions Installation Using the gas surface burnersInstructions Operating Before Lighting a Gas BurnerTop-of-Range Cookware Case of Power FailureUsing the oven controls Installation Instructions Operating Using the ovenInstructions Safety Instructions Troubleshooting TipsBroiling Guide How to Set the Oven for Broiling-Close the oven doorBroiling Guide HI BroilUsing the clock and timer How to Set an Immediate Start and Automatic Stop Using the timed baking and roasting featuresHow to Set a Delayed Start and Automatic Stop Instructions Operating InstructionsTroubleshooting Tips Consumer Support Using the probe. on some modelsHow to Set the Oven For Roasting When Using the Probe Installation InstructionsConvection Bake Using the convection ovenConvection Roast Adapting Recipes…Multi-Shelf Baking Troubleshooting Tips Consumer SupportHow to Set the Oven for Convection Baking or Roasting Touch the Convection Roast pad Meats Minutes/Lb Oven Temp Convection Roasting Guide-Suggested SettingsTouch the Convection Bake pad Using the timed convection baking featuresConsumer Support Troubleshooting Tips Installation Safety Instructions Special features of your oven controlFahrenheit or Celsius Temperature Selection Hour Shut-OffHour, 24 Hour or Clock Black-Out Control Lockout on some modelsCook and Hold Your control is set to use a 12 hour clockOperating Instructions Using the Sabbath Feature. on some modelsInstructions Troubleshooting Tips Installation Instructions Operating Instructions Adjust the oven thermostat-Do it yourselfTo Adjust the Thermostat Type of margarine will affect baking performanceWhen Using the Warming Drawer Using the electric warming drawerOn Signal Light Control KnobTo Warm Serving Bowls and Plates Temperature Selection ChartHow to Set the Oven for Cleaning Using the self-cleaning ovenBefore a Clean Cycle After a Clean Cycle Operating Instructions SafetyHow to Delay the Start of Cleaning Sealed Burner Assemblies Care and cleaning of the rangeReplacement After cleaningBurner Caps and Heads Burner capsInstallation Instructions Broiler Pan and Grid Lift-Off Oven DoorOven Heating Elements Warming Drawer Pan Safety Instructions OperatingRemovable Warming Drawer on some models To remove the warming drawerUnlock the touch pads after cleaning Lock out the touch pads before cleaningOven Air Vents Upper Control PanelOven Shelves Oven Light ReplacementTo remove Do not remove any screws to remove the coverFor Your Safety Installation of the rangeCommonwealth of Massachusetts Before YOU BeginMust Never be Less than 24 Inches Consumer Support Dimensions and ClearancesOperating Instructions Installation Troubleshooting TipsTools YOU will Need Gas line shut-off valveGas Supply Requirements Consumer Support TroubleshootingProvide Adequate Gas Supply Recommended Gas Pipe Outlet LocationsRecommended Electrical Outlet Locations Electrical Power Supply RequirementsProvide Proper Electrical Supply Flexible Connector Hookup Rigid Pipe Hookup Options Support TroubleshootingTips Connect the Range to the Gas SupplyInstructions Troubleshooting Tips Consumer Support InstallationUsing an Existing Nema 14-50R Receptacle Operating Instructions Replace the Power Cord OptionalWire Power Cord Installation Option Safety Instructions Wire Conduit Installation OptionWire used, location and enclosure Installation Instructions Operating Instructions SafetyReplace the Wire Cover Assemble Surface Burners Seal the OpeningsCheck Ignition of Surface Burners Electric IgnitionQuality of Flames Instructions Operating Instructions Safety InstructionsLevel the Range Yellow flamesInstall the Anti-Tip Device Safety Instructions Operating InstructionsWhen All Hookups Are Completed Performed by a qualified LP gas installerProblem Possible Causes What To Do Before you call for service…Oven temperature See the Installation of the range sectionSee the Adjust the oven thermostat-Do it yourself Clock and timerClean cycle Oven not clean afterIs on when you want Power outageConvection fan Fan noiseNot working Drawer does not slideLooking For Something More? AccessoriesWe’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Safety Instructions Operating GE Dual Fuel Range WarrantyGE Will Replace What GE Will Not CoverParts and Accessories Schedule ServiceConsumer Support GE Appliances Website Real Life Design Studio

J2B915 specifications

The GE J2B915 is an advanced gas turbine engine that represents a significant milestone in aerospace technology, primarily designed for use in regional and business aircraft. Engineered by General Electric, the J2B915 combines innovative design features with state-of-the-art technologies to provide high performance, reliability, and efficiency.

At the heart of the J2B915 is its powerful core, which is designed to operate at high temperatures and pressures. This capability allows the engine to deliver substantial thrust while maintaining a relatively low fuel consumption rate. The engine achieves this efficiency through its advanced compressor and turbine design. The axial-flow compressor, known for its ability to compress air efficiently, contributes to the overall performance of the engine, while the high-pressure turbine extracts energy effectively to drive the compressor.

One of the standout features of the J2B915 is its noise reduction technology. In an era where environmental regulations are becoming increasingly stringent, the engine's design incorporates features aimed at minimizing noise footprint during operation. This is achieved through the use of advanced acoustic materials and innovative turbine blade designs, which work together to reduce noise levels while ensuring optimal performance.

Another key characteristic of the J2B915 is its modular design, which enhances maintainability and serviceability. This modularity allows for easier access to engine components, simplifying routine inspections and repairs. The design philosophy also translates to a reduction in downtime, which is critical for commercial operators seeking to maximize aircraft availability.

The GE J2B915 also boasts impressive durability and reliability. Engineered with advanced materials and coatings, it is capable of withstanding the rigors of continuous operation in various environments. The engine’s reliability is bolstered by GE’s rigorous testing protocols and quality assurance processes, ensuring that it meets the high standards expected by operators worldwide.

In terms of controls and monitoring, the J2B915 utilizes an advanced digital engine control system. This system monitors various performance parameters in real-time, allowing for precise management of engine functions and enhancing operational efficiency. The digital technology also supports predictive maintenance, alerting operators to potential issues before they escalate into more significant problems.

In conclusion, the GE J2B915 gas turbine engine embodies a blend of cutting-edge technologies, robust design, and a commitment to performance. Its high efficiency, low noise output, and reliable operation make it a preferred choice for regional and business aviation markets, cementing its reputation in the competitive landscape of aerospace propulsion systems.