GE J2B915 installation instructions Must Never be Less than 24 Inches

Page 39

WARNING! INSTALLATION SAFETY INSTRUCTIONS

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this manual. For assistance or additional information, consult a qualified installer, service agency, manufacturer (dealer) or the gas supplier.

Safety Instructions

Never reuse old flexible connectors. The use of old flexible connectors can cause gas leaks and personal injury. Always use NEW flexible connectors when installing a gas appliance.

IMPORTANT: Remove all packing material and literature from oven before connecting gas and electrical supply to range.

Have your range installed by a qualified installer.

Your range must be electrically grounded in accordance with local codes or, in the absence of local codes, in accordance with the National Electrical Code (ANSI/NFPA 70, latest edition).

Before installing your range on linoleum or any other synthetic floor covering, make sure the floor covering can withstand 180°F without shrinking, warping or discoloring.

Do not install the range over carpeting unless a sheet of 1/4″ thick plywood or similar insulator is placed between the range and carpeting.

Make sure the wall coverings around the range can withstand heat generated by the range up to 200°F.

Avoid placing cabinets above the range. To reduce the hazard caused by reaching over the open flames of operating burners,

install a ventilation hood over the range that projects forward at least 5″ beyond the front of the cabinets.

The ventilating hood must be constructed of sheet metal not less than 0.0122″ thick.

Install above the cooktop with a clearance of not less than 1/4″ between the hood and the underside of the combustible material or metal cabinet. The hood must be at least as wide as the appliance and centered over the appliance. Clearance between the cooking surface and the ventilation hood surface

MUST NEVER BE LESS THAN 24 INCHES.

EXCEPTION: Installation of a listed microwave oven or cooking appliance over the cooktop shall conform to the installation instructions packed with that appliance.

If cabinets are placed above the range, allow a minimum clearance of 30″ between the cooking surface and the bottom of unprotected cabinets.

If a 30″ clearance between cooking surface and overhead combustible material or metal cabinets cannot be maintained, protect the

underside of the cabinets above the cooktop with not less than 1/4″ insulating millboard

covered with sheet metal not less than 0.0122″ thick.

Clearance between the cooking surface and protected cabinets MUST NEVER BE LESS THAN 24 INCHES. The vertical distance from the plane of the cooking surface to

the bottom of adjacent overhead cabinets extending closer than 1″ to the plane of the range sides must not be less than 18″. (See the Dimensions and Clearances illustration in this section.)

CAUTION: Items of interest to children should not be stored in cabinets above a range or on the backsplash of a range—children climbing on the range to reach items could be seriously injured.

Operating Instructions Installation Instructions Troubleshooting Tips Consumer Support

39

Image 39
Contents Write the model and serial numbers here Model # Serial # Installation InstructionsANTI-TIP Device Install ANTI-TIP Devices Packed with RangeAll ranges can tip and injury could result Safety Precautions Important Safety NoticeSafety Surface Burners Safety InstructionsElectric Warming Drawer Cook Meat and Poultry THOROUGHLY… SELF-CLEANING OvenInstructions Safety Instructions Support Troubleshooting TipsBefore Lighting a Gas Burner Using the gas surface burnersInstructions Installation Instructions OperatingTop-of-Range Cookware Case of Power FailureUsing the oven controls Using the oven Instructions SafetyInstallation Instructions Operating Instructions Troubleshooting TipsHI Broil How to Set the Oven for Broiling-Close the oven doorBroiling Guide Broiling GuideUsing the clock and timer Instructions Operating Instructions Using the timed baking and roasting featuresHow to Set an Immediate Start and Automatic Stop How to Set a Delayed Start and Automatic StopInstallation Instructions Using the probe. on some modelsTroubleshooting Tips Consumer Support How to Set the Oven For Roasting When Using the ProbeAdapting Recipes… Using the convection ovenConvection Bake Convection RoastTroubleshooting Tips Consumer Support How to Set the Oven for Convection Baking or RoastingMulti-Shelf Baking Touch the Convection Roast pad Meats Minutes/Lb Oven Temp Convection Roasting Guide-Suggested SettingsUsing the timed convection baking features Consumer Support Troubleshooting Tips InstallationTouch the Convection Bake pad Hour Shut-Off Special features of your oven controlSafety Instructions Fahrenheit or Celsius Temperature SelectionYour control is set to use a 12 hour clock Control Lockout on some modelsHour, 24 Hour or Clock Black-Out Cook and HoldUsing the Sabbath Feature. on some models Instructions Troubleshooting TipsOperating Instructions Type of margarine will affect baking performance Adjust the oven thermostat-Do it yourselfInstallation Instructions Operating Instructions To Adjust the ThermostatControl Knob Using the electric warming drawerWhen Using the Warming Drawer On Signal LightTo Warm Serving Bowls and Plates Temperature Selection ChartUsing the self-cleaning oven Before a Clean CycleHow to Set the Oven for Cleaning Operating Instructions Safety How to Delay the Start of CleaningAfter a Clean Cycle Sealed Burner Assemblies Care and cleaning of the rangeBurner caps After cleaningReplacement Burner Caps and HeadsInstallation Instructions Lift-Off Oven Door Oven Heating ElementsBroiler Pan and Grid To remove the warming drawer Safety Instructions OperatingWarming Drawer Pan Removable Warming Drawer on some modelsUpper Control Panel Lock out the touch pads before cleaningUnlock the touch pads after cleaning Oven Air VentsDo not remove any screws to remove the cover Oven Light ReplacementOven Shelves To removeBefore YOU Begin Installation of the rangeFor Your Safety Commonwealth of MassachusettsMust Never be Less than 24 Inches Consumer Support Dimensions and ClearancesGas line shut-off valve Troubleshooting TipsOperating Instructions Installation Tools YOU will NeedRecommended Gas Pipe Outlet Locations Consumer Support TroubleshootingGas Supply Requirements Provide Adequate Gas SupplyElectrical Power Supply Requirements Provide Proper Electrical SupplyRecommended Electrical Outlet Locations Connect the Range to the Gas Supply Support TroubleshootingFlexible Connector Hookup Rigid Pipe Hookup Options TipsOperating Instructions Replace the Power Cord Optional InstallationInstructions Troubleshooting Tips Consumer Support Using an Existing Nema 14-50R ReceptacleWire Power Cord Installation Option Safety Instructions Wire Conduit Installation OptionInstallation Instructions Operating Instructions Safety Replace the Wire CoverWire used, location and enclosure Electric Ignition Seal the OpeningsAssemble Surface Burners Check Ignition of Surface BurnersYellow flames Instructions Operating Instructions Safety InstructionsQuality of Flames Level the RangePerformed by a qualified LP gas installer Safety Instructions Operating InstructionsInstall the Anti-Tip Device When All Hookups Are CompletedProblem Possible Causes What To Do Before you call for service…Clock and timer See the Installation of the range sectionOven temperature See the Adjust the oven thermostat-Do it yourselfPower outage Oven not clean afterClean cycle Is on when you wantDrawer does not slide Fan noiseConvection fan Not workingLooking For Something More? AccessoriesWe’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration What GE Will Not Cover GE Dual Fuel Range WarrantySafety Instructions Operating GE Will ReplaceReal Life Design Studio Schedule ServiceParts and Accessories Consumer Support GE Appliances Website

J2B915 specifications

The GE J2B915 is an advanced gas turbine engine that represents a significant milestone in aerospace technology, primarily designed for use in regional and business aircraft. Engineered by General Electric, the J2B915 combines innovative design features with state-of-the-art technologies to provide high performance, reliability, and efficiency.

At the heart of the J2B915 is its powerful core, which is designed to operate at high temperatures and pressures. This capability allows the engine to deliver substantial thrust while maintaining a relatively low fuel consumption rate. The engine achieves this efficiency through its advanced compressor and turbine design. The axial-flow compressor, known for its ability to compress air efficiently, contributes to the overall performance of the engine, while the high-pressure turbine extracts energy effectively to drive the compressor.

One of the standout features of the J2B915 is its noise reduction technology. In an era where environmental regulations are becoming increasingly stringent, the engine's design incorporates features aimed at minimizing noise footprint during operation. This is achieved through the use of advanced acoustic materials and innovative turbine blade designs, which work together to reduce noise levels while ensuring optimal performance.

Another key characteristic of the J2B915 is its modular design, which enhances maintainability and serviceability. This modularity allows for easier access to engine components, simplifying routine inspections and repairs. The design philosophy also translates to a reduction in downtime, which is critical for commercial operators seeking to maximize aircraft availability.

The GE J2B915 also boasts impressive durability and reliability. Engineered with advanced materials and coatings, it is capable of withstanding the rigors of continuous operation in various environments. The engine’s reliability is bolstered by GE’s rigorous testing protocols and quality assurance processes, ensuring that it meets the high standards expected by operators worldwide.

In terms of controls and monitoring, the J2B915 utilizes an advanced digital engine control system. This system monitors various performance parameters in real-time, allowing for precise management of engine functions and enhancing operational efficiency. The digital technology also supports predictive maintenance, alerting operators to potential issues before they escalate into more significant problems.

In conclusion, the GE J2B915 gas turbine engine embodies a blend of cutting-edge technologies, robust design, and a commitment to performance. Its high efficiency, low noise output, and reliable operation make it a preferred choice for regional and business aviation markets, cementing its reputation in the competitive landscape of aerospace propulsion systems.