GE 164D3333P185-1 owner manual Instructions Safety Removable Oven Bottom, Cleaning the Oven Bottom

Page 20

Instructions

Care and cleaning of the range.

Instructions Safety

Removable Oven Bottom

First remove the shelves from the oven. The oven bottom lifts from the rear. Grasp each side of the oven bottom and lift upward from the rear until the bottom is clear—lift it to remove from the front.

NOTE: If the oven bottom is replaced incorrectly, it may warp and cause undesirable baking results.

Instructions Care and Cleaning Operating

Cleaning the Oven Bottom

The oven bottom has a porcelain enamel finish.

To make cleaning easier, protect the oven bottom from excessive spillovers. This is particularly important when baking a fruit pie or other foods with high acid content. Hot fruit fillings or foods that are acidic in content, such as tomatoes or sauerkraut, and sauces with vinegar or lemon juice, may cause pitting and damage to the porcelain enamel surface.

To protect the oven bottom surface, place a piece of aluminum foil slightly larger than the baking dish on the shelf below to catch any boilovers. It should not completely cover the shelf as this would cause uneven heat in the oven. Aluminum foil should not be placed on the oven bottom.

If a spillover does occur on the oven bottom, allow the oven to cool first. You can clean the bottom with soap and water, a mild abrasive cleanser, soap-filled steel wool pads or an oven cleaner following package directions.

Customer Service Troubleshooting Tips Installation

Broiler Drawer

The broiler pan is held in place by a wire broiler rack.

To open the broiler:

Gently lift up and pull forward on the drop down broiler door.

Pull the broiler pan forward. It will reach a temporary stop position.

Continue to pull forward and the broiler pan will pull out to expose the entire broiler grill surface.

Remove the broiler pan from the broiler rack by lifting up on the front of the broiler pan so it will clear the wire rack. Then pull forward slightly and use both hands to lift the pan free of the rack.

To return the pan to the broiler rack:

Pull the wire rack out to the stop position.

Insert the pan into the recessed section of the broiler rack.

Slide the pan in place under the pan retainers. Push the pan to the rear of the broiler compartment.

Close the broiler door.

20

Image 20
Contents Ranges20″ and 24″ Gas Part No D3333P185-1 Pub. No -8955-3180-6C139 04-01 JROperating Instructions Safety Instructions Customer ServiceService Partnership Troubleshooting Tips Customer ServiceStaple sales slip or cancelled check here Congratulations You Are Now Part of Our FamilySafety Precautions Installation Instructions Operating Instructions Care and CleaningSurface Cooking Units Safety Instructions Operating Instructions Care Cleaning Installation InstructionsUsing the surface burners InstructionsLighting Instructions for Electric Ignition Models Lighting Instructions for Standing Pilot ModelsAir Adjustment How to Select Flame SizeSafety Instructions Operating Troubleshooting Tips Customer ServiceUsing the oven Instructions Safety InstructionsPower Outage-Electric Ignition Models To light the oven pilot during an electrical power outageOven Shelves Care and CleaningOven Control Oven Vents Installation Instructions Care and CleaningOven Shelf Positions Using the oven for baking How to Set the Oven For BakingInstructions Care and Cleaning Preheating Troubleshooting Tips Pan PlacementCleaning Operating Oven Shelves Tips Installation CakesCustomer Service Don’t Peek CookiesUsing the oven for roasting How to Set the Oven For RoastingUsing the oven for broiling Safety InstructionsHow to Set Your Oven for Broiling Use of Aluminum FoilSafety Instructions Operating Broiling GuideCare and cleaning of the range How to Remove the Range for Cleaning and ServicingLift-Up/Off Cooktop Burner GratesInstallation Instructions Oven Shelves BurnersControl Panel and Knobs Metal PartsInstructions Safety Removable Oven Bottom Cleaning the Oven BottomInstructions Care and Cleaning Operating To open the broilerBroiler Pan Lift-Off Oven Door on some modelsLet the range cool before cleaning Porcelain Oven InteriorBefore You Begin Installation of the rangeFor Your Safety Cleaning Operating Instructions Dimensions and ClearancesImportant Safety Instructions Additional Materials You May Need Installing the BackguardTools You Will Need Range Location Recommended gas and electric supply locationAnti-Tip Bracket Installation Instructions Anti-Tip BracketConverting Burner Orifices to LP Gas Converting Burner Orifices to Natural GasRegulator Conversion Harper-Wyman Regulator SCP RegulatorConnect the Range to Gas Checking Manifold Gas PressureElectrical Grounding Instructions Operating InstructionsOven Operation Oven Pilot AdjustmentIf Range Has Electric Ignition Surface Burner Air Shutter Adjustment Oven Burner Air Shutter AdjustmentCleaning If adjustments are necessaryModel and Serial Number Location When All Hookups Are CompleteMobile Home Installation Before You Call For Service… Problem Possible Causes What To DoGas Range Warranty What is Not CoveredWe Will Replace, At No Charge To You CareSchedule Service Parts and AccessoriesConsumer Support GE Appliances Website Real Life Design Studio

164D3333P185-1 specifications

The GE 164D3333P185-1 is a high-performance component designed for industrial applications, particularly in the field of electrical engineering. This product demonstrates a blend of advanced technology, reliability, and efficiency, which makes it a preferred choice for various sectors.

One of the standout features of the GE 164D3333P185-1 is its robust design. Constructed with durable materials, it is built to withstand challenging environmental conditions. This durability ensures that it maintains performance integrity over time, minimizing the need for maintenance and reducing downtime in industrial operations.

The component incorporates state-of-the-art technologies that enhance its functionality. It utilizes advanced sensor technology, which allows for precise monitoring and control of electrical systems. This capability is crucial in applications where accuracy and reliability are paramount. Additionally, the GE 164D3333P185-1 is equipped with innovative power management features that improve energy efficiency, leading to cost savings in operational expenses.

Another key characteristic of the GE 164D3333P185-1 is its versatility. It can be seamlessly integrated into various systems, whether in manufacturing, energy production, or commercial applications. This adaptability makes it a valuable asset in the ever-evolving industrial landscape.

The GE 164D3333P185-1 also promotes enhanced safety features. It includes built-in protection mechanisms that guard against electrical surges and faults, ensuring a safe operational environment. This attribute is particularly important for organizations that prioritize safety and risk management as part of their operational protocols.

Moreover, the ease of installation and user-friendly interface of the GE 164D3333P185-1 simplify the integration process. Technicians can efficiently set up and operate the component without extensive training, leading to quicker project turnaround times.

In summary, the GE 164D3333P185-1 is an exemplary product that showcases the best of modern engineering. With its robust design, advanced technologies, energy efficiency, safety features, and versatility, it stands as a critical component for industries looking to enhance their operational capabilities. Adopting the GE 164D3333P185-1 means investing in a future-proof solution that addresses the demands of today's dynamic industrial environments.