West Bend L4978 instruction

the bread maker. Remember, the bread maker is not human and cannot adjust for mismeasured ingredients, ONLY YOU CAN MAKE SURE THE INGREDIENTS ARE MEASURED ACCURATELY. Follow these VERY IMPORTANT tips when measuring ingredients: Read through the recipe and organize the ingredients you will need in the order they are added to the bread pan. Many bread disasters occur because an ingredient was left out or added twice. Use standard kitchen measuring cups and spoons and follow the steps below.

1.ALWAYS use glass or plastic “see through” liquid measuring cups to measure liquids. Place cup on flat surface and measure at “EYE LEVEL,” not at an angle. The liquid level line MUST be right to the measurement marking, not above or below. A “looks close enough” measurement can spell disaster in bread making. SPECIAL TIP: Place liquid measuring cup on inside of kitchen cabinet for easier measuring at eye level.

2.ALWAYS use standard dry measuring cups for measuring all dry ingredients

especially flour. Dry measuring cups are those that nest together. ALWAYS SPOON DRY INGREDIENTS INTO THE SPECIFIED MEASURING CUP, THEN LEVEL OFF TOP WITH A KNIFE. All measurements must be level. DO NOT SCOOP measuring cups into the dry ingredients for measuring as you will compress the ingredients into the cup and end up with more than intended which will result in a short loaf of bread.

SPECIAL TIP: To lighten flour before measuring, move a spoon through it several times.

3.ALWAYS use standard measuring spoons for measuring ingredients such as yeast, salt, sugar, dry milk, etc. as well as small amounts of honey, molasses or water. Again, the measurements MUST BE LEVEL, not rounded or heaping as this little bit of difference can affect the bread. DO NOT USE TABLEWARE AS MEASURING

SPOONS AS THESE VARY IN SIZE AND WILL NOT BE ACCURATE.

USING BREAD MIXES IN YOUR BREAD MAKER - Pre-packaged bread

mixes can be prepared in your bread maker. Follow the directions for making up to a 1½ pound (3 cup) loaf. Use the BASIC or BASIC RAPID Bread Setting for bread mixes unless preparing a 100% whole wheat or natural grain bread mix, which would require the use of the WHOLE WHEAT or WHOLE WHEAT RAPID Bread Setting. Add the recommended amount of liquid

to the bread pan first, then the flour mixture and finally the yeast on top. Select desired Bread Color and start the bread maker. The delay start timer can also be used with bread mixes providing no perishable ingredients are used, such as milk, eggs, etc., which will spoil when left at room temperature for several hours.

MAKE YOUR OWN MIXES - To save time and money, you can prepare your own bread mixes ahead of time and store in the refrigerator until ready to use. Simply measure all dry ingredients in recipes, EXCEPT YEAST, into a plastic bag and close with a twist tie. Label as to the type of bread and loaf size. When ready to use, simply add liquid ingredients to pan as recipe directs. Then add the dry mixture, level, add the butter or margarine and the yeast on top. Program and start the bread maker. Use delay timer if recipe recommends its use.

MEASUREMENT EQUIVALENT CHART

CUP	=	FLUID OUNCE	=	TABLESPOON		= TEASPOON
1	=	8	=	16	=	48
⅞	=	7	=	14	=	42
¾	=	6	=	12	=	36
⅔	=	5⅓	=	10⅔	=	32
⅝	=	5	=	10	=	30
½	=	4	=	8	=	24
⅜	=	3	=	6	=	18
⅓	=	2⅔	=	5⅓	=	16
¼	=	2	=	4	=	12
⅛	=	1	=	2	=	6
		½	=	1	=	3
		¼	=	½	=	1½

L4978 specifications

West Bend L4978 is a powerful integrated circuit designed primarily for driving high-voltage and high-current loads. It is an essential component in various applications that require reliable and efficient power management. The L4978 offers a versatile and robust solution for a range of electronic devices, including power supplies and motor controllers.

One of the key features of the West Bend L4978 is its ability to handle wide voltage input ranges. It operates effectively within a voltage range of 8 to 40 volts, making it suitable for both automotive and industrial applications. This flexibility allows designers to incorporate the L4978 into diverse systems without the need for extensive redesigns.

Another significant characteristic of the L4978 is its high current output capability. It can deliver up to 1 amp of output current, allowing it to drive larger loads efficiently. This high current output is coupled with built-in thermal protection, ensuring the device remains operational even under challenging conditions.

The L4978 also integrates several advanced technologies that enhance its performance. For instance, it features a high-speed protection circuit that safeguards against overheating and overcurrent situations. This protection not only ensures the longevity of the device but also increases overall system reliability.

In terms of efficiency, the L4978 stands out with its low standby current consumption, making it an excellent choice for battery-operated devices. Its design minimizes energy wastage, which is crucial in applications where power efficiency is paramount.

Furthermore, the L4978 allows for easy implementation in various applications. It provides a simple configuration for both linear and switching power supplies, accommodating the needs of different designs without requiring extensive modifications.

In summary, the West Bend L4978 is a highly versatile integrated circuit designed for robust power management. Its wide voltage range, high output current capability, advanced protection features, and energy efficiency make it an ideal choice for a plethora of applications in the electronics industry. With its reliable performance and adaptability, the L4978 continues to play a crucial role in modern electronic design, supporting innovations across multiple fields.