Multiquip MQ62TDD manual Tow Hitch Coupler Requires a 2-inch ball hitch

Page 19

PUMP COMPONENTS

Figure 4 shows the location of the components and basic components for the MQ62TDD trash pump, The function of each component or control is described below:

1.Lifting Bail – When lifting of the trash pump by crane is required, use this lifting bail. Note: this lifting bail is balanced for a fully configured trash pump; removal of any trash pump components will un-balance the lifting bail.

2.Pump Discharge Port – Discharges water and debris from the pump.

3.Muffler/Guard – DO NOT touch the muffler when engine is running. The muffler can become extremely hot, causing severe burns. NEVER run the pump with the muffler guard removed.

4.Oil Filler – Fill as recommended in the maintenance section of this manual.

5.Engine (Diesel) – This pump uses a Deutz F2L2011/ D2011L02 air-cooled, 4-stroke diesel engine. See the Deutz Operation manual supplied with the trash pump for additional engine information.

6.Control Box Panel – Monitors engine functions and will shut down the engine for low oil pressure, high coolant temperature, alternator charge and V-belt failure.

7.Battery – +12 VDC battery compartment.

8.Tow End Jack Stand – When connecting the pump to a ball type towing hitch, use this jack stand to raise and lower the pump.

9.Fuel Filler Port – When the adding of fuel is required, remove fuel cap and add fuel through this port. Re- fuel using only recommended types of diesel fuels (see Deutz Operation Manual). DO NOT top off fuel, wipe up any spilled fuel immediately.

10.Tow Hitch Coupler – Requires a 2-inch ball hitch.

11.Safety Chain – ALWAYS attach safety chain to the towing vehicle. NEVER! tow the trash pump with the safety chain unattached.

12.Documentation Box – Contains documentation for the pump and engine.

13.Fuel Cell – This pump can be configured to operate with either a 16, 23 or 41 gallon fuel cell.

14.Tie-Downs – When the pump is placed on a flatbed truck for transport, use these tie-down points (4) to secure the trailer frame to the flatbed.

15.Fuel Cell Drain Plug – Located underneath the fuel cell, remove this drain plug to drain the fuel tank.

16.Engine Throttle Lever – Controls the speed of the engine. For load conditions (pumping water) ALWAYS run the engine at full speed.

17.Dipstick – Read this gauge to determine the oil level in the engine crankcase. Fill with only recommended type oil as referenced in the maintenance section of this manual.

18.Fuel Filter – Replace or clean the fuel filter as specified in the maintenance section of this manual.

19.Chock Blocks – Place these blocks (not included as part of the trash pump package) under each trailer wheel to prevent rolling.

20.Fuel Gauge – Read this gauge to determin if the fuel level is low is low. If fuel level is low, replenish with only recommended type diesel fuel.

21.Clean-Out Cover – Remove this cover to clean and remove foreign debris from the trash pump.

22.Accessories – Hoses, strainers and clamps are the required accessory components for normal operation of this trash pump. Contact your nearest Multiquip dealer for information on the components.

23.Trailer Lights – Before towing trash pump, make sure that both trailer lights are functioning correctly. NEVER tow the trash pump if these lights are not working.

24.Pump Intake Port – Intakes water and debris from the source.

25.Fill Cap – Remove this cap to prime the pump with water.

MQ62TDD TRASH PUMP • OPERATION AND PARTS MANUAL — REV. #0 (07/30/09) — PAGE 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model MQ62TDD Proposition 65 Warning Reporting Safety Defects Reporting Safety DefectsMQ62TDD Trash Pump Table of ContentsOrdering parts has never been easier Parts Ordering ProceduresTraining Checklist Training ChecklistRead Operator’s Manual completely Daily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistFor Your Safety and Safety of Others SafetySafety Rules and Regulations General SafetyWinter drain water from pump housing to prevent freezing Transporting Pump Specifications SpecificationsDimensions Trailer Mount Dimensions PUMP/TRAILERDimensions Skid Mount Dimensionsskid MountGeneral Information Terms to Know ApplicationsPump Components Pump ComponentsTow Hitch Coupler Requires a 2-inch ball hitch Deutz Engine Basic Components Engine ComponentsControl BOX Components Ignition Switch Used to start and stop the engineEngine Oil BatteryBattery Cable Installation InspectionFuel FuelBefore Starting SetupEngine Startup STARTUP/OPERATIONOperation Pump Storage SHUTDOWN/STORAGEEngine SHUT-DOWN Pump Inspection After USEPump Vacuum Test Maintenance PumpTo perform the pump vacuum test do the following General Inspection Air Cleaner Maintenance EngineAir Cleaner with Dust Indicator Changing Fuel Filter Check Oil LevelChanging Engine Oil Changing Oil FilterBattery Electrolyte Level Battery MaintenanceWheel Bearings Hubs Maintenance TrailerAdjustable Channel Wheel Hub AdjustmentSuspension Torque Requirements Leaf SuspensionTrailerTowing Guidelines Trailer Safety GuidelinesTrailer Safety Information Common Causes for Loss of TrailerCoupling to the Tow Vehicle Driving ConditionsInoperable Brakes, Lights or Mirrors Reporting Safety DefectsTrailer Towing Tips Vehicle VIN Tag Trailer VIN TagTow Vehicle Electrical ConnectorSafety Chains Trailer Lighting and Braking ConnectorLatching mechanism Coupler TypesBall Hitch Coupler Ball Hitch Coupler Pintle Eye CouplerCoupling theTrailer to theTowVehicle Ball Coupler Lower the trailer until the coupler fullyConnecting Trailer Lights Attaching Safety ChainUncoupling the Ball Hitch Tighten lug nuts before each tow Tire SafetyTire Safety Unsafe Tires, Lug Nuts or WheelsStep Determining Load Limit of TrailerDetermining Load Limit of Tow Vehicle Step P indicates the tire is for passenger vehicles Tire FundamentalsReference for additional tire information for light trucks Tire Safety TipsWheels, Bearings and Lug Nuts Tire RepairReplacing Worn or Damaged Tires Wheel RimsLug Nut Torque Requirements Lights and Signals Trailer Lights Wiring DiagramPump Troubleshooting Troubleshooting PumpEngine Troubleshooting Troubleshooting EngineSympton Possible Problem Solution Page Wiring Diagram OLD Style Wiring Diagram NEW Style Explanation of Code in Remarks Column Sample Parts ListTo 3 units Suggested Spare PartsNameplate and Decals 49002 7005000BH21008 NPA-320JTrash Pump Assy 1603000090 260100001026200000240002 46070000900002Trash Pump Assy 0451250120 01050908150451290080 0105091225Trailer Trlrmpxf Assy 29242 0205 SCREW, HHC 3/8 16 x 40019514 10019 NUT, Nyloc 10133 NUT, Nyloc 3/8 29228Trailer TRLR50XF Assy 6109210 BOLT, 1/2 13 x 1-1/2 86109180 10019 NUT, Nyloc 10133 NUT, Nyloc 3/8 190436109160 NUT Skid Assy 19091 Axle Assy 29755 29381U29381S SPRING, 4 Leaf 29381B 46749Lifting Bail ASSY. Trlrmpxf 0105051640 16 X 40 Bolt 2103200 190923019091 Lifting Bail ASSY. TRLR50XF 0105051640 16 X 40 Bolt 020316130 50XF9102Lifting Bail ASSY. Skid 6109210 13 x 1-1/2 Bolt 6109810 Fuel ASSY. Trlrmpxf 6109152 6109210 13 x 1-1/2 Bolt 61092085284 84454Fuel ASSY. TRLR50XF 3122302E-41FGC Fuel ASSY. Skid Part Name Battery ASSY. Trlrmpxf 34506 3459634597 0165306531Battery ASSY. TRLR50XF 6109108 Battery ASSY. Skid BOLT, Battery Hold Down Engine Mounting ASSY. Trlrmpxf 13211 016212070 Bolt 344006109210 BOLT, HEX Head 1/2-13X1-1/2 XXX001 XXX002Engine Mounting ASSY. TRLR50XF Engine Mounting ASSY. TRLR50XF Engine Mounting ASSY. Skid 60TDD008 2101030 10 x 30 HEX Bolt 03021640063541 020310080Engine Assy F2L20116728 OIL Pressure Switch Assy 01118971 118248401118718 Temperature Transmitter Assy 01143531 01182377Starter Assy 01319265 0118238401181390 01340070Control BOX ASSY. OLD Style 01182528 0118038401180382 01180383Control BOX ASSY. NEW Style 34707 34708EM98206 34709AIR Filter Assy 02169927 0117942804272299 01112824Narrow V-BELT Assy 01179565 Lubricated OIL Filter Assy 01174416 Fuel Filter Assy 04270708 Freight Policy Terms and Conditions of Sale PartsPage HERE’S HOW to GET Help

MQ62TDD specifications

The Multiquip MQ62TDD is a robust engine-driven compressor designed to deliver exceptional performance and reliability in challenging job site conditions. This portable unit is engineered for a wide range of applications, including construction, HVAC, and industrial use. With its powerful engine and user-friendly features, the MQ62TDD stands out as an ideal choice for contractors needing dependable air supply on the go.

One of the primary features of the MQ62TDD is its impressive air output. The unit boasts a maximum air flow rate of up to 62 CFM, allowing it to power multiple pneumatic tools simultaneously. Whether you are operating jackhammers, nail guns, or air impact wrenches, the MQ62TDD ensures consistent and sufficient air pressure to keep your projects moving efficiently.

The MQ62TDD is equipped with a 9-horsepower Honda engine, providing the necessary power to drive the compressor. Honda engines are renowned for their durability and fuel efficiency, and this model is no exception. With an extended run time due to its large fuel tank, the MQ62TDD minimizes downtime, which can be crucial in time-sensitive projects.

In terms of technological advancements, the MQ62TDD features an advanced cooling system designed to keep the compressor operating at optimal temperatures, thus extending the lifespan of the unit. The unit’s lightweight design, combined with a sturdy frame, makes transportation on site straightforward. The integrated handle and collapsible wheels facilitate easy maneuverability, ensuring that the compressor can be relocated without hassle.

Safety is also a priority with the Multiquip MQ62TDD. The unit is designed with protective features such as a low oil shutdown mechanism, which helps to prevent engine damage by automatically turning off if the oil level gets too low. Additionally, the compressor features sound-dampening technology that significantly reduces noise levels, making it ideal for use in noise-sensitive environments.

Overall, the Multiquip MQ62TDD compressor is a versatile, durable, and user-friendly tool that meets the demands of professional contractors. With its high air output, reliable power source, advanced technologies, and safety features, it provides the efficiency and performance needed to tackle any job with confidence.
Top Page Image Contents