AEG PV.500-MH manual Dimensions and Views, Appropriate Use, Inappropriate Use, Safety

Page 21

Protect PV.500_MH Operating Instructions

3.2Dimensions and Views

Figure 3 Dimensions and views

3.3Appropriate Use

Only operate the equipment with the maximum permissible con- nection values stated in the technical data sheet. Any other use or modification constitutes inappropriate use.

Unauthorised repairs, manipulations or changes made to the equipment and its safety devices without the manufacturer's ap- proval are not permitted. The manufacturer cannot be held liable for damage resulting from such repairs, manipulations or changes.

Safety

The equipment will operate reliably and safely subject to compli- ance with the instructions, the operating and equipment specifica- tions and regulations set out by the Employer's Liability Insurance Association.

3.4Inappropriate Use

No liability is accepted if the equipment is used for applications not intended by the manufacturer (= inappropriate use). Inappropriate use can cause serious or fatal personal injury. The responsibility for any measures necessary for the prevention of personal injury or damage to property is borne by the equipment operator or user.

80000043212 BAL

21 of 68

Image 21
Contents Operating Instructions Protect PV.500-MHAEG Power Solutions GmbH Table of Contents Monitoring Systems, Messages and Faults System FunctionInterfaces Graphical Display and Operation Unit Warranty Information on How to Use these InstructionsGeneral Information ValidityExplanations of Target Groups Target GroupsObligations of the Equipment Operator HandlingSkilled Personnel Skills and Training Obligations of skilled personnel Storing InstructionsExplanation of Symbols and Safety Instructions Explanation of SymbolsSymbol Meaning Signal Words Used Safety InstructionsHazard Symbols Used Symbol Meaning for skilled personnelSigns Containing Orders for Personal Protective Equipment Emergency Procedure e.g. in the Event of a Fire Safety AwarenessAbbreviations Particular Dangers associated with Photovoltaic Systems Thin-film cellsLightning protection Safety and Protection Devices for the Equipment Safety Signs and Warning Notices on the EquipmentSystem stop switch Protective CoversLockable Equipment Doors GuardResidual Hazards Electrical Hazards Fire-Related Risks Risks Due to Moving PartsWater in electrical equipment Risk of injury due to rotating fansRisks due to Loss of Control Risks from Maintenance and Repair WorkProduct Details Product DescriptionImportant information about equipment documenta- tion Safety Dimensions and ViewsAppropriate Use Inappropriate UseNameplate Standards, Directives and CE MarkTechnology Operating Elements Individual Operation System DescriptionDescription of Sequence Control System FunctionOFF Status Waiting for Feed Conditions StatusWaiting Status Operation StatusNight Status Fault StatusSequence Control During the Course of the Day Early morningEvening DayLater in the evening NightPermissible voltage dip after switching on the stack Inverter stack switch-on timePower limit value for shutdown, delay time for shutdown Sequence Control ParametersFan Control, Cabinet Fan Description of Fan Control GeneralFan Control, Inverter Stack Fan Cabinet Fan Control ParametersIgbt temperature limit Igbt temperature limit value for switching off the fanParameters of Inverter Stack Fan Control Insulation Monitoring and Earthing of PV Cells GeneralProtect PV.500-MH Operating Instructions Operation with Thin-Film Solar Cells Maintenance modeGeneral Sequence controlMinimum time in maintenance mode Delay for shutdown of K21 in night operationInsulation Monitoring Parameters MPP TrackerMonitoring Systems, Messages and Faults Temperature monitoring systems Table of FaultsCan I/O monitoring systems Fault/Message Unit Monitoring Systems Fault/Message DC voltage monitoring systems Fault/Message Communication Interface InterfacesCommunication data port 1 Technical Data MultiCom CCC hardware data assembly A29.1Communication data port 2 Communication data port 3Structure of the MultiCom CCC Interface Configuration jumpersConnections ButtonDescription of serial interfaces Shield connection of the RS485 bus line Port 2 X5 RS485 pin assignment defaultPort 2 X5 RS232 pin assignment ConfigurationController Area Network can at Port 3 X4 can pin assignmentSetting the terminal program Configuration PreparationsProtect PV.500MH Operating Instructions Data protocol configuration Configuring the Modbus ProtocolModbus/JBus data transmission configuration Configuring Modbus Data TransmissionStructure of the COM Server internally wired to A93 COM Server GeneralNetwork Connection Installation of the COM Server Configuration of the Virtual COM Port Network Integration ConfigurationRemote Signalling Technical dataStructure Following default signals are used for remote signalling DOU Graphical Display and Operation UnitAcoustic signal generator SignallingKeyboard Operation LEDsStart-up Possible symbol keys and their functionMain Menu Menu Structure Menu TreeOperating display Normal operation Operating DisplayExample of operating display Examples of possible displaysSolar radiation is too low, the inverter is in standby mode Monthly data t = day 1 31 for the last 12 months Example of yearly overview Status/Measured Values MenuMenu Inverter example BlockingSettings Fault HistoryService Information