AEG PV.500-MH manual Standards, Directives and CE Mark, Nameplate

Page 22

Protect PV.500-MH Operating Instructions

3.5Standards, Directives and CE Mark

The equipment complies with currently applicable DIN and VDE regulations. The requirements of BGVA3 are met on the basis of compliance with EN 50274/VDE 0660-51.

The requirements of VDE 0100, Part 410, IEC 60364-4-41, "Func- tional extra-low voltage with safe isolation" and IEC 62109, "Safety of power converters for use in photovoltaic power systems" have been complied with where applicable.

The CE mark on the unit confirms compliance with the EC frame- work directives for 2006/95/EC (Low Voltage) and for 2004/108/EC (Electromagnetic Compatibility), provided that the actions outlined in the instructions are observed.

3.6Nameplate

The following information appears on the nameplate:

Figure 4 Rating plate (example)

22 of 68

80000043212 BAL

Image 22

Contents Protect PV.500-MH Operating InstructionsAEG Power Solutions GmbH Table of Contents System Function Monitoring Systems, Messages and FaultsInterfaces Graphical Display and Operation Unit General Information Information on How to Use these InstructionsWarranty ValidityObligations of the Equipment Operator Target GroupsExplanations of Target Groups HandlingSkilled Personnel Skills and Training Storing Instructions Obligations of skilled personnelExplanation of Symbols Explanation of Symbols and Safety InstructionsSymbol Meaning Hazard Symbols Used Safety InstructionsSignal Words Used Symbol Meaning for skilled personnelSigns Containing Orders for Personal Protective Equipment Safety Awareness Emergency Procedure e.g. in the Event of a FireAbbreviations Thin-film cells Particular Dangers associated with Photovoltaic SystemsLightning protection System stop switch Safety Signs and Warning Notices on the EquipmentSafety and Protection Devices for the Equipment Protective CoversGuard Lockable Equipment DoorsResidual Hazards Electrical Hazards Water in electrical equipment Risks Due to Moving PartsFire-Related Risks Risk of injury due to rotating fansRisks from Maintenance and Repair Work Risks due to Loss of ControlProduct Description Product DetailsImportant information about equipment documenta- tion Appropriate Use Dimensions and ViewsSafety Inappropriate UseStandards, Directives and CE Mark NameplateTechnology Operating Elements System Description Individual OperationOFF Status System FunctionDescription of Sequence Control Waiting for Feed Conditions StatusOperation Status Waiting StatusSequence Control During the Course of the Day Fault StatusNight Status Early morningLater in the evening DayEvening NightPower limit value for shutdown, delay time for shutdown Inverter stack switch-on timePermissible voltage dip after switching on the stack Sequence Control ParametersDescription of Fan Control General Fan Control, Cabinet FanCabinet Fan Control Parameters Fan Control, Inverter Stack FanParameters of Inverter Stack Fan Control Igbt temperature limit value for switching off the fanIgbt temperature limit Insulation Monitoring and Earthing of PV Cells GeneralProtect PV.500-MH Operating Instructions General Maintenance modeOperation with Thin-Film Solar Cells Sequence controlInsulation Monitoring Parameters Delay for shutdown of K21 in night operationMinimum time in maintenance mode MPP TrackerMonitoring Systems, Messages and Faults Table of Faults Temperature monitoring systemsCan I/O monitoring systems Fault/Message Unit Monitoring Systems Fault/Message DC voltage monitoring systems Fault/Message Interfaces Communication InterfaceCommunication data port 2 Technical Data MultiCom CCC hardware data assembly A29.1Communication data port 1 Communication data port 3Connections Configuration jumpersStructure of the MultiCom CCC Interface ButtonDescription of serial interfaces Port 2 X5 RS485 pin assignment default Shield connection of the RS485 bus lineController Area Network can at ConfigurationPort 2 X5 RS232 pin assignment Port 3 X4 can pin assignmentConfiguration Preparations Setting the terminal programProtect PV.500MH Operating Instructions Configuring the Modbus Protocol Data protocol configurationConfiguring Modbus Data Transmission Modbus/JBus data transmission configurationCOM Server General Structure of the COM Server internally wired to A93Network Connection Installation of the COM Server Network Integration Configuration Configuration of the Virtual COM PortTechnical data Remote SignallingStructure Following default signals are used for remote signalling Graphical Display and Operation Unit DOUKeyboard Operation SignallingAcoustic signal generator LEDsPossible symbol keys and their function Start-upMenu Structure Menu Tree Main MenuOperating Display Operating display Normal operationExamples of possible displays Example of operating displaySolar radiation is too low, the inverter is in standby mode Monthly data t = day 1 31 for the last 12 months Example of yearly overview Menu Status/Measured ValuesBlocking Menu Inverter exampleService Fault HistorySettings Information