Middleby Cooking Systems Group PS536 manual SP Lock, Overtemp, Actual

Page 19

SECTION3-OPERATION

"SP LOCK"

Light

Lights when the

set point is locked out from changes.

This setting can

only be changed by service personnel.

OVERTEMP

Light

Lights when the oven

temperature is

greater than 650°F (343°C). Refer to Quick Reference: Troubleshooting in this section.

Temperature

Key

Press this key once

to view the Actual

Temperature in the

Display.

 

 

Display

 

 

 

 

"HEAT ON"

Shows the Set Point

 

 

 

 

 

 

Light

or the Actual Tem-

 

 

 

 

Lights when the

perature in degrees

 

 

 

burner or heating

Fahrenheit (F) or

 

 

 

 

 

elements, as

 

Celsius (C).

 

 

 

appropriate for the

 

 

 

 

 

 

 

 

 

 

 

 

oven model, are in

 

 

 

 

 

 

 

 

 

 

 

 

 

 

operation.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENGLISH

"SET PT" (setpoint)

Light

Lights when the

set point is shown

in the display.

"ACTUAL

TEMP" Light

Lights when the Actual Tempera- ture is shown in the display.

Service Key

Service use

only.

 

 

Set Point Key

Unlock Key

 

Press this key

Press this key

Up Arrow and Down

together with the

Unlock Key to allow

together with the Set

Arrow Keys

the Set Point to be

Point Key to allow the

Set Point to be

Press these keys to

changed.

changed. Changes

adjust the Set Point up or

Changes can only be

can only be made for

down. If the Set Point will

made for 60 sec-

60 seconds.

not change, refer to Set

onds.

 

Point Key and Unlock Key

 

 

in this section.

 

19

Image 19
Contents PS536 Gas and Electric Ovens English Table of Contents Conveyor Drive Motor Moves the conveyor III. Oven SpecificationsOven Uses II. Oven Components see FigureElectrical specifications for electric ovens per oven cavity Installation Installation Kit Installation KIT see FigureOther ventilation concerns II. Ventilation SystemRequirements RecommendationsTop panel and base pad installation III. AssemblyStacking Restraint Cable InstallationAssembling and tensioning the conveyor Conveyor Installation10 Conveyor placement Final AssemblyConnection Rate regulator Must be installed in the line BeforeVI. Electrical Supply VII. GAS SupplyGas Conversion Gas Utility Rough-In RecommendationsLocation and Description of Controls Turn the Blower switch to the on I position If the oven uses this Digital Temperature ControllerII. Normal Operation STEP-BY-STEP Sary Press the Set Point Unlock keys at Same time. Wait 5b. Adjust the temperatureTemperature, if neces Controller to a desired setLight III. Quick Reference Digital Temperature ControllersOvertemp SP LockActual IV. Quick Reference Troubleshooting Perform the normal startup procedure Maintenance DailyIII. Maintenance Every 3 Months II. Maintenance MonthlySplit Belt Disassembly and Cleaning Disassembling the idler shaft Slide the two sections of each shaft apartLubricating the Blower Fan Bearings IV. Maintenance Every 6 MonthsKEY Spare Parts KIT Available sepa- rately. See Figure Blower BeltElectrical Wiring Diagrams Wiring diagram, PS536 Electric Oven 208/230V, 60 Hz, 3 Ph Wiring diagram, PS536 Electric Oven 380V, 50 Hz, 3 Ph English Français