Middleby Cooking Systems Group PS536 5b. Adjust the temperature, Controller to a desired set

Page 17

SECTION3-OPERATION

If the oven uses this Digital Temperature Controller:

5b. Adjust the temperature

controller to a desired set

temperature, if neces-

B.DAILYSHUTDOWNPROCEDURE

1.Turn the "BLOWER" () and "CONVEYOR" ()

switches to the "OFF" ("O") position. Open the window (if so equipped) to allow the oven to cool faster.

Note that the blowers will remain in operation until the oven has cooled to below 200°F (93°C).

+

ENGLISH

sary.

+

• Press the Set Point

 

and Unlock keys at

 

the same time. Wait

wait

for the "SET PT" light

to turn on.

for

• Press the Up Arrow

 

and Down Arrow

 

Keys as necessary

or

to adjust the set-

point.

 

6b. Check that the "HEAT ON"

 

light illuminates.

This

wait

shows that the burner or

heating elements

have

for

been turned on.

 

 

7b. Wait for the oven to heat to the setpoint temperature. Higher setpoint temperatures will require a longer wait. The oven can reach a temperature of 500°F (232°C) in approximately 5 minutes.

8b. (Optional) Press the Tem- perature () key to show

the Actual Temperature

 

in the display, and wait

 

for the "ACTUAL TEMP"

 

light to turn on. This al-

 

lows you to monitor the

 

oven temperature as it

wait

rises to the setpoint.

for

9b. Allow the oven to preheat for 10 minutes after it has reached the set point temperature.

3.After the oven has cooled and the blowers are off, switch the circuit breaker/fused disconnect to the off position.

IMPORTANT

On gas ovens, if the "HEAT ON" light will not illuminate, OR if the oven does not heat, the gas burner may not have lit. Turn the "BLOWER" () and "CONVEYOR" () switches to the "OFF" ("O") position. Wait for AT LEAST FIVE MIN- UTES before restarting the oven. Then, repeat the Daily Startup procedure.

CAUTION

In case of power failure, turn all switches to the “OFF” ("O") position, open the oven window (if so equipped), and remove the product. After the power has been restored, perform the normal startup procedure. IF THE OVEN WAS SWITCHED OFF FOR LESS THAN 5 MINUTES, WAIT FOR AT LEAST FIVE MINUTES BEFORE RESTARTING THE OVEN.

No attempt should be made to operate the oven during a power failure. In gas ovens, the burner will not operate and gas will not flow through the burner without electric power.

17

Image 17
Contents PS536 Gas and Electric Ovens English Table of Contents Oven Uses III. Oven SpecificationsII. Oven Components see Figure Conveyor Drive Motor Moves the conveyorElectrical specifications for electric ovens per oven cavity Installation Installation Kit Installation KIT see FigureRequirements II. Ventilation SystemRecommendations Other ventilation concernsTop panel and base pad installation III. AssemblyStacking Restraint Cable InstallationAssembling and tensioning the conveyor Conveyor Installation10 Conveyor placement Final AssemblyVI. Electrical Supply Rate regulator Must be installed in the line BeforeVII. GAS Supply ConnectionGas Conversion Gas Utility Rough-In RecommendationsLocation and Description of Controls II. Normal Operation STEP-BY-STEP If the oven uses this Digital Temperature ControllerTurn the Blower switch to the on I position Temperature, if neces 5b. Adjust the temperatureController to a desired set Sary Press the Set Point Unlock keys at Same time. WaitLight III. Quick Reference Digital Temperature ControllersActual SP LockOvertemp IV. Quick Reference Troubleshooting Perform the normal startup procedure Maintenance DailySplit Belt Disassembly and Cleaning II. Maintenance MonthlyIII. Maintenance Every 3 Months Disassembling the idler shaft Slide the two sections of each shaft apartKEY Spare Parts KIT Available sepa- rately. See Figure IV. Maintenance Every 6 MonthsBlower Belt Lubricating the Blower Fan BearingsElectrical Wiring Diagrams Wiring diagram, PS536 Electric Oven 208/230V, 60 Hz, 3 Ph Wiring diagram, PS536 Electric Oven 380V, 50 Hz, 3 Ph English Français