Turbo Chef Technologies 2020 manual Preventing Oven Damage, Grounding Instructions

Page 8

i i S A F ET Y INFORMATION

Preventing Oven Damage

οWhen servicing this appliance, do not tear insulation to get to components. Rather, find the edge of the insulation and remove the tape that holds it in place.

οClean the oven daily.

οClean the oven only with TurboChef Oven Cleaner.

οx DO NOT clean with a water jet.

οx DO NOT allow cleaning solution or water to remain in the cook cavity longer than necessary.

Grounding Instructions

WARNING: Improper grounding increases the risk of electric shock.

This appliance must be grounded. The cord is equipped with a grounding wire and plug, which in the event of an electrical short circuit, reduce the risk of electric shock by providing an escape wire for the electric current. The wire must be plugged into an outlet that is properly installed and grounded.

Consult a qualified electrician or serviceman to determine whether or not the appliance is properly grounded.

οx DO NOT use an extension cord. If the power supply cord is too short, request a qualified electrician or serviceman to install an outlet near the appliance.

Power Cord Replacement

To avoid potential hazards, only the manufacturer, its service agent, or a similarly-qualified person should replace a damaged power cord.

Page 7 Page 9
Image 8
Page 7 Page 9
Contents TurboChef Technologies, Inc Page For further information, call 800.90TURBOPage Table of Contents Oven Systems TroubleshootingSchematics Reducing Fire Risk Important Safety Information Please Read FirstGeneral Safety Information Power Cord Replacement Preventing Oven DamageGrounding Instructions S a F ET Y InformationSpecifications and Installation Page Dimensions Electrical SpecificationsExterior ConveyorInstallation Instructions PackagingCertifications Oven ConstructionStacking Ovens Bracket BBInstallation Near Open Heat Source Ventilation Requirements Partition Counter Top / TableCleaning Daily and Weekly Page Daily Cleaning Instructions Approved cleaner, part numberWeekly Cleaning Instructions L E a N I N GRemove Inner Oven Components Clean Oven Components Ready the Oven for Use Standard Oven Operation Page Oven Controls Cooking a Product Mode 1 Oven OffMode 2 Belt Speed Select Mode 3 Warming Mode 4 SoakingMode 6 Cooling Down Mode 7 IdleEditing a Cooking Profile Changing a Cooking Profile NameAdjusting the Temperature Adjusting the Top and Bottom AirThis page intentionally Left blank Oven Modes Page Config Mode Setup ModeAccessing the Fault Count Screen Accessing the Setup ModeChanging the Display Temperature Updating the FirmwareEdit Modes Select Screen Changing the Display LanguageTest Mode Accessing the Heat Control ScreenViewing the Status Indicators Entering a New Serial Number Bottom Display LineErasing Oven Settings To erase oven settings, press L3 ,Initiating a Burn-In Test Viewing the Serial NumberOven Systems Page Output 24 VDC is on terminals -V and +V Keypad is an 11-key membrane switchControl System Voltage is applied, the relay is Functioning normallyRelay Relay, Solid State K5/K4 HeatersConveyor System Gear Drive Conveyor MotorDisconnect line voltage from the unit Gear Drive Conveyor Motor Speed Controller CmscConvection System Blower Motor Speed Controller BmscBlower Motor HeatersTroubleshooting Page Overview of Troubleshooting Fault Code DescriptionsFault Code Table RO U B L E S H O OT I N GFault Code Troubleshooting Blower Motor Troubleshooting Correctly installed? Test the RTD page 22 for resistance/ temperature chartTroubleshoot the blowers pages Are all elements heatingTroubleshoot F1 fault pages Temperature chartIs the solid state Relay functioning Properly?Clean the air Oven clean?Check Wiring pages YES Is the oven hot? noIs the wiring correct pages 37-40? A-8 Open the right end bellReplace the I/O no control board A-8 Is the high limit thermostatTroubleshooting F9 Belt Fault Total Belt Run Failure Correct wiring pagesSettings correctly Correspond with TurboChef settings Remove the chain guard page A-4Non-Fault Code Troubleshooting Relocate oven to cooler areaClose proximity ObstructionCorrectly reinstall Plates Does the problem OperationBlower and/or Installed? BMSCs, heaters And/or wiringCorrect wiring Power?Check wiring from Ribbon cable Board. Correct wiring ifSchematics Page H E MAT I C S RTD H E MAT I C S Cmsc Parameters Appendix Replacing Oven Components Page Replacing Oven Components Part DetailsEnd Bells A-6 A-8 A-4 This page intentionally Left blank Replacing Items Outside of End Bells Figure A-1 Front Oven ComponentsPart Number Hardware Description Figure A-5 Blower Motor Assembly Detail Replacing Items Left End BellPart Number Hardware Description Hardware Part Numbers Replacing Items Right End Bell RTDRTD Page Page For service or information
Related manuals
Manual 36 pages 936 b

2020 specifications

Turbo Chef Technologies 2620,2020 is a revolutionary cooking appliance that merges advanced technology with user-friendly operation. Designed for commercial kitchens, it stands out as a versatile solution for various cooking methods, meeting the demands of fast-paced environments while ensuring consistent results.

One of the main features of the Turbo Chef 2620 is its innovative cook technology that incorporates a combination of convection, microwave, and radiant heat. This tri-technology system allows food to be cooked quickly and evenly, which not only saves time but also enhances the quality of the final product. The appliance employs a patented air impingement system, ensuring that heat circulates uniformly around the food. This results in crispy exteriors and moist interiors, making it ideal for items like pizza, baked goods, and meats.

In addition to its cooking capabilities, the Turbo Chef 2620 is equipped with a user-friendly digital control panel. The intuitive interface allows for easy programming and access to a variety of cooking presets, making it accessible even for inexperienced staff. Operators can store multiple cooking profiles, streamlining operations and improving efficiency. The appliance also features a robust construction, built to withstand the demands of high-volume use, ensuring durability and longevity in busy kitchen settings.

Another significant characteristic of the Turbo Chef 2620 is its energy efficiency. The appliance is designed to minimize energy consumption without sacrificing performance, making it an environmentally friendly choice for commercial kitchens. Its compact size allows for flexible placement, making it suitable for establishments with limited space.

Furthermore, the Turbo Chef 2620 ensures food safety and ease of maintenance. The appliance's design includes removable components that facilitate easy cleaning, while essential safety features protect users during operation.

Overall, Turbo Chef Technologies 2620,2020 is a groundbreaking appliance that offers an impressive array of features and technologies for modern cooking needs. With its advanced cooking capabilities, user-friendly operation, energy efficiency, and robust design, it represents an ideal solution for any commercial kitchen looking to enhance productivity while maintaining high food quality.
Top Page Image Contents