Vita-Mix XTG012 Ontrol Panel, Blending Station MP, Speed Control, High/Low Pulse, Programs

Vita-Mix XTG012 owner manual Blending Station MP Vita-Mix XTG012 owner manual Important Safeguards Vita-Mix XTG012 owner manual Figure a Vita-Mix XTG012 owner manual Ontrol Panel, Blending Station MP, Speed Control, High/Low Pulse, Programs Vita-Mix XTG012 owner manual NORM, WARM, HOT, a usage count and a total, Cannot be cleared Vita-Mix XTG012 owner manual Turn the machine on Remove the container from the machine Vita-Mix XTG012 owner manual Custom Vita-Mix XTG012 owner manual Id Assembly, Two-Part Lid, One-Piece Lid optional, Cover with Removable Hinge Design Vita-Mix XTG012 owner manual Back Cover, Push until back of cover is seated against the Motor Base Vita-Mix XTG012 owner manual Preparing the counter area, Electrical requirements, VAC 50/60 Hz 15 Amps Vita-Mix XTG012 owner manual Blending Station dimensions Vita-Mix XTG012 owner manual Counter Gasket, Gasket Installation Instructions Vita-Mix XTG012 owner manual Lending Tips, Never start the motor before the container is in place Vita-Mix XTG012 owner manual Nstructions Vita-Mix XTG012 owner manual PRE-SET Program, Remove the container, pour, garnish and serve the drink Vita-Mix XTG012 owner manual Until the desired speed, Desired speed Vita-Mix XTG012 owner manual Retainer Nut Removal, Do not force. Do not attempt to disassemble blade assembly Vita-Mix XTG012 owner manual Arts List, Item# Part, #15569, #15567, #1159 48 oz .4 liter Lid plug #15566 Vita-Mix XTG012 owner manual #1159 #15574 #15575 Vita-Mix XTG012 owner manual Are and Cleaning, Care Note Vita-Mix XTG012 owner manual Motor Base, Control Panel, Lid, Cover Door, In-Counter Gasket Vita-Mix XTG012 owner manual Container, Do not soak the blade agitator assembly Vita-Mix XTG012 Pecifications, Blending Station MP On-Counter, Blending Station MP In-Counter, Power Requirements Vita-Mix XTG012 Roubleshooting, Top nine problems you can fix on your own, Problem Solution #1, Solution #2, Solution #3 Vita-Mix XTG012 owner manual Cooling the motor, Solution #4 Vita-Mix XTG012 owner manual Arranty, Limited Warranty Vita-Mix XTG012 owner manual Ervice Contract
Page 4

C ontrol Panel

Display Window

Start/Stop

Speed Control

MAXIMUM PERFORMANCE

Six Factory Pre-Set

Owner Controls

High/Low Pulse

Programs

 

 

Blending Station® MP

ON/OFF switch - Located on the side of the Motor Base, the ON/OFF switch controls the power to the machine. With the machine plugged in, switch the machine to ON to ready the machine for blending.

START/STOP button - Pressing START/STOP once starts and runs the machine and turns the blades. Press the START/STOP button again to stop the machine and the blades. (NOTE: Pressing one of the PRE-SET PROGRAM buttons, while the motor is running, will also stop the machine.)

SPEED CONTROL button - Press the ▲ button to gradually increase the speed of the blades in increments of 1%, up to 100%. Press the ▼ button to gradually decrease the speed of the blades in increments of 1%, down to 7%. SPEED CONTROL is used to set the blending speed of the PULSE buttons (see Instructions, pg. 15) and the START/STOP button (see Instructions, pg. 16). NOTE: These settings will reset if the power is shut off.

PRE-SET PROGRAM buttons - These buttons, numbered 1 thru 6, are pre-programmed blending cycles designed for the most commonly made drinks. Depending on the viscosity of the drink you are creating, pressing one of the six PRE-SET PROGRAM buttons will run the machine for a full cycle. The machine will stop by itself when the cycle is complete. A cycle varies in speed and length; see the Instructions on page 14 for a complete description of the range of each PRE-SET button. Due to the difference of recipes, your results may vary.

See page 6 for information on Custom Programming these six buttons.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Blending Station MP Important Safeguards Figure a Ontrol Panel Blending Station MPSpeed Control High/Low PulseNORM, WARM, HOT, a usage count and a total. Cannot be clearedTurn the machine on Turn the machine on Remove the container from the machineCustom Id Assembly Two-Part LidOne-Piece Lid optional Cover with Removable Hinge DesignBack Cover Push until back of cover is seated against the Motor BaseDo not strike the blender when removing from the counter Preparing the counter areaElectrical requirements VAC 50/60 Hz 15 AmpsBlending Station dimensions Gasket Installation Instructions Counter GasketLending Tips Never start the motor before the container is in placeNstructions PRE-SET Program Remove the container, pour, garnish and serve the drinkUntil the desired speed Desired speedDo not force. Do not attempt to disassemble blade assembly Retainer Nut RemovalArts List Item# Part#15569 #15567#1159 #15574 #15575 Are and Cleaning Care NoteMotor Base Control PanelLid Cover DoorDo not soak the blade agitator assembly ContainerPower Requirements PecificationsBlending Station MP On-Counter Blending Station MP In-CounterTop nine problems you can fix on your own Problem Solution #1Solution #2 Solution #3Solution #4 Cooling the motorLimited Warranty ArrantyErvice Contract Foodservice Division Usher Road, Cleveland, Ohio 44138-2103 USA
Top Page Image Contents