Kenmore Kitchen Grill Range END Panel Removal or Installation, Modular Ranges, Coil TOP Ranges

Page 30

_f

RANGE END PANEL REMOVAL OR INSTALLATION

WARNING - Disconnect electrical power to range before beginning installation

The end panel kit consists of:

Two End Panels (RH & L H,)

Two End Panel Brackets

Eight Screws

Instatlation instruction sheet

MODULAR RANGES

TO REMOVE END PANEL:

1_ Remove both modules from range top

2From inside of modular opening remove the screw (circle A)

3Remove the two screws from the back of end panel,

4Move the end panel out at the rear and slide out from behind the front trim

FOR BUILT-IN INSTALLATION ONLY:

COIL TOP RANGES

TO REMOVE END PANEL:

tRaise cooktop and securely support or have it held, remove screw B

2Remove the two screws from the back of end Panel_

3Move the end panel out at the rear and slide out from behind the front trim

This type of installation requires that the end panels be removed (if equipped) and two toe protectors, part no

1325189, be installed (if not equipped) The toe protectors are listed in the repair parts book and can be ordered through the Sears service center

1 Remove end panels as shown above

2, install toe protectors as shown, using existing screws on range,

FOR BUILT-IN INSTALLATION ONLY:

1Remove end panels as shown above

2install toe protectors as shown, using existing screws on range

FRONT

BRACKET ON END PA

INSTALL TOE PROTECTORS/.

FOR BUILT_IN__

FRONT TRIM

INSTALLATION ONLY ._'_

INSTALL TOE PROTECTORS		. ." ,'
FOR BUILT-IN	"_-._,	'
INSTALLATION ONLY

TO INSTALL END PANEL:

1_ Attach end panel bracket to end panel with screw provided

2 Position the end panel behind the front trim

and tight to the underside of the cooktop frame,

3, Align the two holes in the back of end panel with holes in range back and attach with

screws provided°

4_ From inside of modular opening, drive a screw into bracket. (Circle A)

TO INSTALL END PANEL:

1, Remove toe protectors and replace mounting

screws,

2Position the end panel behind the front trim and tight to the underside of upper side panet,

3o Align the two holes in the back of end panel with holes in range back and attach with screws provided

4, Raise cooktop and securely support or have it held, drive a screw through upper side panel into end panel,

30

Image 30

Contents Kenmore Electric Range Located on the plate Above Ithe top left corner Ers forDo not Heat Unopened Food Containers SELF- Clean OvensSurface Units Keep Oven Vent Ducts UncoveredTabJe Conten Know your kenmore slide=in range SeriesOven Lock Light 10, Oven Signal Light 11, Oven Light Switch Surface Unit Control -- Left Front and ModuleConvertible Color Panels Nickel Plated Oven Racks To Start Setting the ControlsControl Setting Guide Operation FoodTo remove or replace Surface Unit Modules COiL Module Removal and ReplacementModume StepInstalling and Removing Plugjn Steak Grill To InstallTo Clean Steak Grill Steak Grill noCooking on top of the range alUmodels Weight or Control Approximate Cooking TimeThickness Setting GrillModule accessories all 8 surface unit lets you fit the unit size toBAKING/ROASTING Clock and ONE.HOUR TimerOven Cooking BroilingRack Arrangements PAN PlacementOffset Rack Normally, t I/2 to 2 inches of air space should be allowedConsider the Design Electric CookingSelecting Cooking Utensils Consider the MaterialOVEN-COOKED Meals HOLD-WARM ChartHolding and Warming CasseroleCauses Baking PROBLEMS, CAUSES, CorrectionsProblem Probable Too fastRoasting Chart RoastingOven Roasting Tips Positioning Broiler PAN BroilingFood Preparation Broiler FireTo Remove Cleaning an maintenance featuresOven Door Removal To Replace Removable Oven RacksControl Setting Guide Griddle Installing and Removing PLUG-IN GriddleTo Clean Griddle Griddle noOptional Accessory To Install RotisserieROTIlSHISH no To USE the Shish Kebab TouseRotisserie Cooking Timetable Module accessories all modelsWeight Position Approximate rotisserie cooking timesGLASS, Paint Plastic Cleaning ProceduresAluminum Porcelain EnamelBefore a Cleaning Cycle Mowto clean your rangeSELF.CLEANING Oven To SET a Clean Cycle Stop TimeTo adjust oven temperature Adjusting Oven Temp KnobProblem Before Calling the Servbce TechnicianCAUTnON Remove Clips and Tape -- RemoveFreestanding iNSTALLATiON BUILT-IN Installation Slide-insBuilt-in installation drop-ins Top ViewEConstruction To Adjust Width of Backguard Backguard Attachment UnstructuonsCoil TOP Ranges Range END Panel Removal or InstallationModular Ranges FrontPage Ownership WE Service What WE SellFull 90-DAY Warranty on Mechanical Adjustments 2rid Year