Kenmore 795.775796, 795.775636 manual Defrost Control Assembly, Lamp, Control BOX-REFRIGERATOR

Page 56

* Ice Fan Scroll Assembly Replacement

1)Remove the plastic guide for the slides on left side by unscrewing the phillips head screws.

2)Pull the grille forward as shown in the second picture.

3)Disconnect the wire harness of the grille

4)Remove the scroll assembly by loosening 2 screws

(1)

(2)

 

 

 

 

 

 

(3)

(4)

8-5 DEFROST CONTROL ASSEMBLY

The defrost Control assembly consists of the Defrost Sensor and the FUSE-M.

The Defrost Sensor works to defrost automatically. It is attached to the metal side of the Evaporator and senses its temperature. At 72°C, it turns the Defrost Heater off. Fuse-M is a safety device for preventing overheating of the Heater when defrosting.

1.Pull out the grille assembly. (Figure 12)

2.Separate the connector with the Defrost Control assembly and replace the Defrost Control assembly after cutting the Tie Wrap. (Figure 13)

8-6 LAMP

Figure 14

8-6-1 Refrigerator Compartment Lamp

1.Unplug the Refrigerator or disconnect power at the circuit breaker.

2.If necessary, remove the top shelf or shelves.

3.Using a flat instrument, gently pry the cover loose in the front as shown. Rotate downward to remove rear tabs.

4.Make sure the bulbs are cool to the touch. Turn bulbs counterclockwise to remove.

5.Assemble in reverse order by snapping the Lamp Cover in, engaging the rear tabs followed by the front tabs. (Max. 60 W-2EA)

Figure 15

8-6-2 Freezer Compartment Lamp

1.

Unplug refrigerator power cord form outlet.

2.

Using a flat instrument, gently pry the lamp cover

 

loose in the front as shown. Rotate downward to

 

remove the rear tabs.

3.

Make sure the bulb is cool to the touch. Turn the

 

bulb counterclockwise to remove.

4.

Replace with a new 60-watt appliance bulb.

5.

Insert tabs on back of cover into slots in freezer

GRILLE ASSEMBLY

Figure 12

DEFROST-CONTROL

ASSEMBLY

Figure 13

ceiling. Push cover up to snap front into place.

8-7 CONTROL BOX-REFRIGERATOR

1.First, remove all shelves in the refrigerator, than remove the Refrigerator control Box by loosening 2 screws.

CONTROL BOX

COVER LAMP

Figure 16

2.Remove the Refrigerator Control Box by pulling it downward.

3.Disconnect the lead wire on the right position and separate the lamp sockets.

- 56 -

Image 56
Contents Refrigerator Contents Safety PrecautionsSpecifications Parts Identification Operation Explanation Of Each FunctionIce Plus Selection Dispenser Use SelectionDispenser Light Control Of Freezer Fan MotorFreezer and Refrigerator Lamp Auto Off Alarm for Open DoorIce Plus Defrosting removing frost Defect Diagnosis FunctionIce Maker Function Icemaking Mode Harvest ModeFill/Park Position Time to Supply Indications RemarksStage Items Indicator Remarks Division Indicator Contents RemarksWiring Diagram Adjustment CompressorRole CompositionDiagnosis CompressorPositive Temperature Coefficient PTC Starter Define Remove the cover Positive Temperature Coefficient PTCOver Load Protector OLP Category TroubleshootingError Code Summary Troubleshooting With Error Power OffFreezer Sensor Err or YesRefrigerator Sensor Error Wiring dia gramYes Is the connection loose? Pin9 pin10Pin7 pin8 Defrost Sensor ErrorYes Is the connection loose? Reconnect Power Off Icing Room Sensor Error Wiring diagramPin2 BL pin1 BL Icing room Sensor Resistance Pin1 BL pin2 BLDefrost Heater Error CON6 CON3Pin10 WH Pin4 BL Resistance Test Point Ressult Is the connection loose? Yes ReconnectOpen or Short of Fuse-M Heater ResistancePin2 BK Pin3 PR Feedback Voltages Freezer Fan ErrorPin1 WH Pin2 BK Freezer Fan Voltages Pin8 BO Pin9 GN Feedback Voltages Condenser Fan ErrorPin7 SB Pin8 BO Condenser Fan Voltages Icing Room Fan Error ResetPin4 RD Pin4 BL Icing Fan Voltages Pin5 BL Pin6 BN Feedback VoltagesCommunication Error Yes Display PCB Is the connection loose?Pin5 BO pin4 BN Receiver fail Voltages Pin5 BO Pin3 RD Transmitter VoltagesMain PCB Yes Is the connection loose? Pin2 BO pin3 BN Receiver VoltagesMain PCB Pin2 BO pin4 RD Transmitter VoltagesCON2 Cube Mode doesn’t workTroubleshooting Else Yes Cube Mode Pin5 SBPin3 WH Output voltage of auger motorResistance of Dispenser solenoid Crush Mode Doesnt work Wiring diagram Display PCB Yes Is the connection loose?Crush Mode Pin3 WH Output voltage of Auger motorPin7 BL Output voltage of door water valve Water ModePin1 PR Second Water- valve Output voltage of machine room water valveResult 360 ~ 420 Ω Yes First Water- valve Machine room Checking resistance of First-valveFreezer-lamp Doesn’t work CON6CON3Refrigerator-lamp Doesn’t work PartCON4 Pin11 GY Pin10 GYCON3 CON4 Poor cooling in the refrigerator compartmentMain PWB Cutting of jumper wire 1BL 2YL Yes 1RD 2WHResistance of Damper Checking Damper itself Is the resistance Values between 1Over cooling in the refrigerator compartment BK BL CON3Enter the Test 3 Mode Yes Change RCR1You can start the Test Mode Wire ColorAC TPA Test Button DC TPA Push the Test button on the Main PWBHow to check the Fan-Error Component Testing Information How to Measure Sheath HeaterHow to Measure Standard Door Heater AssemblyHow to Switch, Freezer Switch, Refrigerator Measure Door SwitchBeep Button Plunger44 ~ 54 Ω SolenoidTest Points Result How to Geared Motor Cube Solenoid Measure AC Motor Assembly Geared Motor & SolenoidHow to Measure Damper Circuit ExtensionLamp Socket Water Valve Dispense Ice MakerDisassembly Instructions Removing and Replacing Refrigerator DoorsRemoving Refrigerator Door Left Door Figure Right Door FigureDoor Gasket Replacement 1. Insert gasket bracket clips Door Gasket Removal Remove door frame coverRemove gasket bracket clips Remove gasketReplace door frame cover Door AlignmentFAN and FAN Motor Evaporator Defrost Control Assembly LampControl BOX-REFRIGERATOR Refrigerator Compartment LampDisplay PCB Replacement Funnel ReplacementMulti Duct DispenserDuct Door Replacement ICE Corner Door ReplacementIcemaker Assembly SUB PWB for Working DispenserAuger Motor Cover HOW to Remove the Door ICE BIN HOW to Insert the Door ICE BINHOW to Remove and Reinstall the Pullout Drawer Follow Steps to RemoveFollow Steps to Reinstall Water Valve Disassembly Method FAN and FAN Motor Disassembly MethodPull OUT Drawer Hook6871JB1431 by July PCB AssemblyMain PCB Assembly EBR34917102 from Aug Display and Dispenser Drive PCB Assembly Dispenser PWBValve & Water Tube Parts Case Parts LOC No 775*3ST 775*2SW 775*9WB 775*4BI Description LAMP,INCANDESCENT Freezer Parts Refrigerator Parts Door Parts LOCNo 775*3ST 775*2SW 775*9WB 775*4BI Description Dispenser Parts ICE Maker & ICE Bank Parts