Craftsman 917.270961 manual To Adjust Steering Wheel Alignment, Transmission REMOVAL/REPLACE- Ment

Page 25

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move

forward or backward.

•Hold motion control lever in that position and turn engine off..

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely, NOTE: If additional clearance is needed

to get to adjustment bolt, move mower deck height to the lowest position. After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the d rect on it s trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps; repeat above steps until satisfied,

Motion Control

Neutral Lock Gate

Adjustment Bolt

TRANSMISSION REMOVAL/REPLACE- MENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and

before operating the tractor. See

=PURGE TRANSMISSION" in the Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when whee s are positioned straight forward, remove steering wheel and reassemble per

instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are

not adjustable on your tractor, if damage has occurred to affect the front wheel

toe-in or camber, contact your nearest authorized service centerldepartment.

TO REMOVE WHEEL FOR REPAIRS

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert

square key.

• • Replace washers and snap retaining

ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat.tiv'esdue to sl0w leaks, tire sealant may be PUrchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

Retaining Ring

Axle

Cover

I

Square Key

(Reef Wheel Only)

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents £RAFTZMANo General Operation Parts Ordering Back CoverSlope Operation ServiceDo not ChildrenMachine. Tall grass can hide obsta- cles TIONI!! Become AWARE!!! Your Safety is InvolvedProduct Specifications Steering Wheel Attach Steering Wheel Before Removing Tractor From SkidCheck Battery HOW to SET UP Your TractorInstall Seat To Drive Tractor OFF SkidCheck Tire Pressure To Convert to Bagging or DischargingCheck Deck Levelness Check for Proper Position of ALL BeltsWhile Learning HOW to USE Youf All assembly instructions have been completedH L Knowyourtractor HOW to USE Your Tractor To Operate Mower To Adjust Gauge WheelsTo Operate on Hills To TransportBefore Starting the Enigne Check Engine OIL Level To Start EngineADD Gasoline Purge Transmission Mulching Mowing Tips Mowing TipsMaintenance Schedule Lubrication ChartGeneral Recommendations Before Each USEOperator Presence System TiresClean AIR Screen TocleanbatteryandterminalsTo Service PRE-CLEANER Clean AIR INTAKE/COOUNG AreasSpark Plugs IN-LINE Fuel FilterTo Install Mower CleaningTo Level Mower Housing TractorSIDE-TO-SIDE Adjustment To Level Mower HousingFRONT-TO-BACK Adjustment To Adjust Brake Belt InstallationTo Replace Mower Blade Drive Belt Belt RemovalTransaxle Motion Control Lever Neutral Adjustment To Adjust Steering Wheel AlignmentTransmission REMOVAL/REPLACE- Ment Front Wheel TOE-IN/CAMBERReplacing Battery To Start Engine with a Weak BatteryTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor To Remove Hood and Grill AssemblyTo Adjust Throttle Control Cable To Adjust Choke ControlIdle Speed Lever =---,f \Idle Mixture Screw Cylinders Engine Fuel SystemOther EngineoilProblem Troubleshooting ChartCause CorrectionChart Cause ProblemCorrection Slow ProblemcauseTractor -. Model Number SchematicTractor - Model Number Electrical KEY Tractor - Model Number ElectricalTractor - Model Number Chassis and Enclosures IL=Y Part Desciiption Tractor - Model Number 917.270961 Chassisand EnclosuresTractor - Model Number Ground Drive KEY Part Description Tractor --MODEL Number Ground DriveTractor - Model Number 917.270961 Steering Assembly 12000029 Tractor --MODEL Number Steering AssemblyTractor - Model Number EngineOptional Equipment Engine Part Description Part KEY Part Description DESCRIP/1ON Tractor - Model Number Seat AssemblyDecals Tractor --MODEL NumberWheels & Tires Part NO. noTractor - Model Number Liftassembly Tractor - Model Number Lift Assembly Mowerdeck Arm, Suspension, Rear Mower Deck Part NO. noTractor - Model Number Hydro Gear Transaxle - Model Number KL=Y PAR Description Tractor - Model Number Hydro Gear Transaxle . Model Number61SA 392,32 Gasket SET KEY Part Description KEY Part NO. no263060 Page Page Only Ride UP and Down Hill Not Across Hill Suggested Guide for Sighting Slopes for Safe OperationPartsDirect sM

917.270961 specifications

The Craftsman 917.270961 is a remarkable lawn tractor designed for both efficiency and ease of use, making it an excellent choice for homeowners with medium to large yards. This powerful riding mower features a robust 19 horsepower Kohler engine, ensuring reliable performance and the capability to handle various terrains. With a 42-inch cutting deck, it provides a comfortable balance between maneuverability and cutting swath, making it suitable for a wide range of applications.

One of the standout features of the Craftsman 917.270961 is its automatic transmission. This technology allows for a smooth and seamless driving experience, enabling the operator to enjoy effortless control while mowing. With variable speed options, users can easily adjust the pace to suit their mowing style and the conditions of their yard, making it adaptable to various tasks.

The lawn tractor is equipped with a dual-blade system, ensuring a clean and even cut every time. This feature not only enhances the appearance of your lawn but also promotes healthy grass growth. Moreover, the deck is designed with an integrated washout port, facilitating easy cleaning after use and reducing the buildup of grass clippings.

Comfort is another priority in the design of the Craftsman 917.270961. The ergonomic seat is adjustable, allowing users of varying heights to find a comfortable position. The steering wheel is also designed for ease of handling, minimizing fatigue during longer mowing sessions.

For added convenience, this lawn tractor comes with an easy-to-read dashboard that displays essential information such as speed, fuel level, and engine temperature, keeping the user informed about the machine's performance at all times. Furthermore, the large-capacity fuel tank minimizes the need for frequent refueling, allowing for extended mowing sessions without interruptions.

Safety features are integrated throughout the Craftsman 917.270961, including an engine cutoff switch that activates when the operator leaves the seat. This ensures peace of mind while operating the mower, especially in landscapes with obstacles.

Overall, the Craftsman 917.270961 stands out as an efficient, comfortable, and versatile lawn tractor. With its solid engine performance, user-friendly design, and advanced mowing technologies, it is a reliable choice for homeowners aiming to maintain a pristine lawn with ease.
Top Page Image Contents