Craftsman 917.27084 manual Before Starting the Engine

Page 16

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

shipped, from the factory, already filled

iwithThe enginesummer inweightyourtractoroil. has been Check engine oil with tractor on level

ground.

•Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until =FULL" mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See =OIL

VISCOSITY CHART" in the Mainte- nance section of this manual).

•To change engine oil, see the Mainte- nance section in this manual.

ADD GASOLINE

•Fill fuel tank. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide

deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

IMPORTANT: When operating in tempera- tures below 32°F(0°C), use fresh, clean winter grade gasoline to help insure good

_Nweather starting.

ARNING: Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emp- tied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional informa- tion. Never use engine or carburetor cleaner products in the fuel tank or perma- znt damage may occur.

CAUTION: Fill to bottom of gas tank filler neck. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

TO START ENGINE

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Be sure freewheel control is in the transmission engaged position.

•Sit on seat in operating p6sition, depress clutch/brake pedal and set parking brake.

•Place motion control lever in neutral (N) position.

•Move attachment clutch to =DISEN-

GAGED" position.

•Move throttle control to fast position

•Pull choke control out for a cold engine start attempt. For a warm engine start

attempt the choke control may not be needed.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to =START" position and release key as soon as engine starts. Do not run starter Continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, push choke control in, wait a few minutes and try again. If engine still does not start, pull the choke control out and retry.

WARM WEATHER STARTING (50 ° F

AND ABOVE)

•When engine starts, slowly push choke control in until the engine begins to run smoothly. If the engine starts to run roughly, pull the choke control out slight- ly for a few seconds and then continue to push the control in slowly.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50 ° F AND

BELOW)

•When engine starts, slowly push choke control in until the engine begins to run smoothly. Continue to push the choke control in small steps allowing the engine to accept small changes in speed and load, until the choke control is fully in, If the engine starts to run roughly, pull the choke control out slight- ly for a few seconds and then continue to push the control in slowly. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents CRAFTSMAN+ Sears Craftsman Help Line 5 am 5 pm, Mon- SatRepair Parts Parts Ordering Back Cover SafetyProduct Specifications Limited 90 DAY Warranty on BatteryService ChildrenSlope Operation Do notTY is Involved Product Specifications Maintenance AgreementParts Bag contents shown full size Hex Bolt 5116-18 x 1-1/416 x Hex BoAtParts Bag contents not shown full size Parts packed separately in cartonTools Required for Assembly Before Rolling Tractor OFF SkidHOW to SET UP Your Tractor Check BatteryInstall Seat Adjustment KnobTo Convert to Bagging or Discharging HooksCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemH L Page HOW to USE Your Tractor Mower BladesGround Drive EngineTowing Carts and Other Attachments To TransportTo Operate Mower To Operate on HillsBefore Starting the Engine Be sure the tractor is on level ground Mowing TipsRGE Transmission Avoid cutting your lawn when it is wet Lubrication Chart Maintenance ScheduleCustomer Responsibilities Before Each USEBrakeoperation To Sharpen BladeEngine To Service PRE-CLEANER To Service CartridgeAIR Filter Engine Cooling RNSCleaning To Install MowerFuel Filter To Remove MowerTo Levelmowerhousing SIDE-TO-SIDE AdjustmentFRONT-TO-BACK Adjustment To Replace Mower Blade DriveBeltinstallation To Adjust Brake To Replace Motion Drive BeltStationaryIdler Transmission Engine Pulley Clutching IdlerTo Start Engine with a Weak Battery RRANSMISSION REMOVAL/REPLACE- IentFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsReplacing Battery To Remove CABLES, Reverse OrderTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor Final SettingTractor Acceleration TestFuel System Cylinders OtherProblem Cause Roubleshooting ChartCorrection Troubleshooting Chart ProblemReinstall blades sharp edge Battery will not charge Loss of ddveCheck tires for proper air pres SureTractor --MODEL Number Tractor - Model Number Electrical KEY Part DescriptionTractor - Model Number Chassis and Enclosures Tractor - Model Number Chassis and Enclosures KEY Part NO. NO.DESCRIPTIONTractor - Model Number Rounddrive TRACTOR- Model Number GaLeBo,ng Ground Drive KEY Part DescriptionTractor - Model Number Steeringassembly Tractor - Model Number Steering Assembly KEY Part DescriptionOptional Equipment NgineSpark Arrester Oarm Hose B Engine KEY Part DescriptionInch 25A mm Tractor - Model Number 917.270840 Seatassembly Spacers128 x 9sncKEY Part NO. no KEY PartDecals Tractor -- Model NumberWheels & Tires OneTractor - Model Number IFT Assembly 1718 15 ,.\ 16\\Tractor - Model Number Lift Assembly Tractor - Model Number Mower Deck Ng. p Ang, BallTractor - Model Number Iydro Gear Transaxle - Model Number Tractor - Model Number Hydro Gear Transaxle - Model Number 2set 11010LABELKrr J 5i7,2,2 o3 513 803797A 797 544801Gasket SET 634Spring-ValveExhaust Seal-OilBody KEY Part NO. NO. DescriptionSchematic TW,N CYL BiginesPage Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across HillSears

917.27084 specifications

The Craftsman 917.27084 is a versatile lawn tractor that represents the brand's commitment to quality, performance, and ease of use. Known for its powerful engine and user-friendly design, the Craftsman 917.27084 is an ideal choice for homeowners looking to maintain their lawns with efficiency and precision.

At the heart of the 917.27084 is a robust 24 horsepower Briggs & Stratton engine. This engine provides ample power for various mowing tasks while ensuring durability and reliability. The engine is equipped with a hydrostatic transmission system, allowing for smooth acceleration and effortless control, making it easier to navigate around obstacles and tight spaces in your yard.

One of the standout features of the Craftsman 917.27084 is its cutting deck. It boasts a 42-inch cutting width, allowing for efficient mowing of medium to large-sized lawns. The deck is adjustable to multiple cutting heights, giving users the flexibility to achieve their desired lawn appearance. This adaptability is particularly beneficial for those who prefer a well-manicured lawn or want to tailor the cut for different grass types or seasonal needs.

The tractor also includes a comfortable and spacious operator's seat, which is designed for extended use without causing fatigue. The ergonomic steering wheel and control layout further enhance the user experience by making it easy to maneuver the tractor.

Safety is a critical concern with any lawn equipment, and the Craftsman 917.27084 does not disappoint. It includes features such as an automatic safety shut-off system that activates the engine when the operator leaves the seat, minimizing the risk of accidents. Additionally, the front and rear wheels are designed with enhanced traction, ensuring stability on various terrains.

Furthermore, the Craftsman 917.27084 incorporates advanced technology for improved performance. The Easy Start system means that users can quickly get the engine running without hassle. The maintenance-free battery and integrated LED headlights add convenience and increase usability, making it easier to mow at any time of day or in low-light conditions.

Overall, the Craftsman 917.27084 combines power, comfort, and advanced features, making it a reliable choice for lawn care enthusiasts. Whether you have a small yard or a larger property, this lawn tractor provides the right balance of performance and user-friendly design. It’s an investment that simplifies lawn maintenance, allowing you to spend less time mowing and more time enjoying your outdoor space.
Top Page Image Contents