Craftsman 917.27084 manual Tools Required for Assembly, Before Rolling Tractor OFF Skid

Page 8

Your new tractor has been assembled at the factory with exception of those pads left unassembled for shipping purposes. To ensure safe and proper operation of your tract_ all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. Review the video cassette before you begin.

TOOLS REQUIRED FOR

ASSEMBLY

Asocketwrenchset will make assembly easier. Standard wrenchsizesyou need

are

listed below.

 

 

(1)

9/16"

wrench

(1)

3/4" Socket w/

(1)

3/4"

wrench

drive rachet

(2)

1/2"

wrench

(1)

Phillips Screw-

(1)

Utility knife

driver

(1)Pliers

 

(1)

"fire pressure

 

 

 

gauge

When right or left hand is mentioned in this manual, it means, from your point of view, when you are in the operating posi- tion (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

Remove all accessible loose parts and parts boxes from shipping carton (See page 6).

Cut, from top to bottom, along lines on all four corners of shipping carton, and lay panels flat.

Check for any additional loose parts or boxes and remove.

Assemble large flat washer, 3/8 lock washer, 3/8 hex bolt and tighten securel_

Snap steering wheel insert into center of steering wheel.

Remove protective materials from trac- tor hood and grill.

IMPORTANT: Check for and remove any

staples in skid that may puncture tires where tractor is to roll off skid.

Insert

%_3/8 3/8 HexLockwBoltusher

_

Large Rat

._. <-_

7. Washer

Wheel

_Boot

 

Extension

_!/dapter

 

Shaft

_

_

5/16 Hex

5116 L(_knut_

 

B_t

BEFORE ROLLING TRACTOR OFF SKID

ATTACH STEERING WHEEL

ASSEMBLE EXTENSION SHAFT AND BOOT

Slide extension shaft onto lower steer-

ing shaft. Align mounting holes in exten- sion and lower shafts and install 5/16

hex bolt and Iocknut. Tighten securely. -IMPORTANT:Tighten bolt and nut secure- ly to 18-22 ft. Ibs. torque.

Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

Position front wheels of the tractor so they are pointing straight forward.

Slide steering wheel adapter onto steer- ing shaft extension.

Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

 

f--_..,).

 

Lower Steering _

 

._ "-"""_---.

S.aft

/--'I3'

""

 

;-..

o

/ ;

TO ROLL TRACTOR OFF SKID (See Operation section for location and function of controls)

Press lift lever plunger and raise attach merit lift lever to its highest position.

Release parking brake by depressing clutch/brake pedal

Place freewheel control in freewheeling

position to disengage transmission (Se, =TO TRANSPORT" in the Operation section of this manual).

Roll tractor forward off skid.

Remove banding holding discharge guard up against tractor.

8

Image 8
Contents CRAFTSMAN+ Sears Craftsman Help Line 5 am 5 pm, Mon- SatRepair Parts Parts Ordering Back Cover SafetyProduct Specifications Limited 90 DAY Warranty on BatteryService ChildrenSlope Operation Do notTY is Involved Product Specifications Maintenance AgreementParts Bag contents shown full size Hex Bolt 5116-18 x 1-1/416 x Hex BoAtParts Bag contents not shown full size Parts packed separately in cartonTools Required for Assembly Before Rolling Tractor OFF SkidHOW to SET UP Your Tractor Check BatteryInstall Seat Adjustment KnobTo Convert to Bagging or Discharging HooksCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemH L Page HOW to USE Your Tractor Mower BladesGround Drive EngineTowing Carts and Other Attachments To TransportTo Operate Mower To Operate on HillsBefore Starting the Engine RGE Transmission Mowing TipsBe sure the tractor is on level ground Avoid cutting your lawn when it is wet Lubrication Chart Maintenance ScheduleCustomer Responsibilities Before Each USEBrakeoperation To Sharpen BladeEngine To Service PRE-CLEANER To Service CartridgeAIR Filter Engine Cooling RNSCleaning To Install MowerFuel Filter To Remove MowerTo Levelmowerhousing SIDE-TO-SIDE AdjustmentFRONT-TO-BACK Adjustment To Replace Mower Blade DriveBeltinstallation To Adjust Brake To Replace Motion Drive BeltStationaryIdler Transmission Engine Pulley Clutching IdlerTo Start Engine with a Weak Battery RRANSMISSION REMOVAL/REPLACE- IentFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsReplacing Battery To Remove CABLES, Reverse OrderTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor Final SettingFuel System Acceleration TestTractor Cylinders OtherCorrection Roubleshooting ChartProblem Cause Troubleshooting Chart ProblemReinstall blades sharp edge Battery will not charge Loss of ddveCheck tires for proper air pres SureTractor --MODEL Number Tractor - Model Number Electrical KEY Part DescriptionTractor - Model Number Chassis and Enclosures Tractor - Model Number Chassis and Enclosures KEY Part NO. NO.DESCRIPTIONTractor - Model Number Rounddrive TRACTOR- Model Number GaLeBo,ng Ground Drive KEY Part DescriptionTractor - Model Number Steeringassembly Tractor - Model Number Steering Assembly KEY Part DescriptionSpark Arrester NgineOptional Equipment Inch 25A mm Engine KEY Part DescriptionOarm Hose B Tractor - Model Number 917.270840 Seatassembly Spacers128 x 9sncKEY Part NO. no KEY PartDecals Tractor -- Model NumberWheels & Tires OneTractor - Model Number IFT Assembly 1718 15 ,.\ 16\\Tractor - Model Number Lift Assembly Tractor - Model Number Mower Deck Ng. p Ang, BallTractor - Model Number Iydro Gear Transaxle - Model Number Tractor - Model Number Hydro Gear Transaxle - Model Number 2set 11010LABELKrr J 5i7,2,2 o3 513 803797A 797 544801Gasket SET 634Spring-ValveExhaust Seal-OilBody KEY Part NO. NO. DescriptionSchematic TW,N CYL BiginesPage Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across HillSears

917.27084 specifications

The Craftsman 917.27084 is a versatile lawn tractor that represents the brand's commitment to quality, performance, and ease of use. Known for its powerful engine and user-friendly design, the Craftsman 917.27084 is an ideal choice for homeowners looking to maintain their lawns with efficiency and precision.

At the heart of the 917.27084 is a robust 24 horsepower Briggs & Stratton engine. This engine provides ample power for various mowing tasks while ensuring durability and reliability. The engine is equipped with a hydrostatic transmission system, allowing for smooth acceleration and effortless control, making it easier to navigate around obstacles and tight spaces in your yard.

One of the standout features of the Craftsman 917.27084 is its cutting deck. It boasts a 42-inch cutting width, allowing for efficient mowing of medium to large-sized lawns. The deck is adjustable to multiple cutting heights, giving users the flexibility to achieve their desired lawn appearance. This adaptability is particularly beneficial for those who prefer a well-manicured lawn or want to tailor the cut for different grass types or seasonal needs.

The tractor also includes a comfortable and spacious operator's seat, which is designed for extended use without causing fatigue. The ergonomic steering wheel and control layout further enhance the user experience by making it easy to maneuver the tractor.

Safety is a critical concern with any lawn equipment, and the Craftsman 917.27084 does not disappoint. It includes features such as an automatic safety shut-off system that activates the engine when the operator leaves the seat, minimizing the risk of accidents. Additionally, the front and rear wheels are designed with enhanced traction, ensuring stability on various terrains.

Furthermore, the Craftsman 917.27084 incorporates advanced technology for improved performance. The Easy Start system means that users can quickly get the engine running without hassle. The maintenance-free battery and integrated LED headlights add convenience and increase usability, making it easier to mow at any time of day or in low-light conditions.

Overall, the Craftsman 917.27084 combines power, comfort, and advanced features, making it a reliable choice for lawn care enthusiasts. Whether you have a small yard or a larger property, this lawn tractor provides the right balance of performance and user-friendly design. It’s an investment that simplifies lawn maintenance, allowing you to spend less time mowing and more time enjoying your outdoor space.