Craftsman 358.792440 instruction manual Configuring Your Unit, Assembly Information Trimmer Head

Page 7

!Clamp

POWERHEAD

END

30 inches

 

 

I ATTACHMENT

Lower

Shoulde

•

END

Strap

Clamp

o

 

 

 

3.Insert two screws into the screw holes.

4.Secure shoulder strap clamp by tightening screws with the hex wrench.

5.Insert your right arm and head through the shoulder strap and al- low it to rest on your left shoulder. Make sure the danger sign is on your back and the hook is to the

right side of your waist.

NOTE: A one-half twist is built in the

shoulder strap to allow the strap to rest flat on the shoulder.

6.Adjust the strap, allowing the book to be about 6 inches below the waist.

7.Fasten the strap hook to the clamp

and lift the tool to the operating position.

8.Try on shoulder strap and adjust for fit and balance before starting the engine or beginning a cutting operation.

NOTE: It may be necessary to relo- cate the shoulder strap clamp on the shaft for proper balancing of unit.

HARNESS

ADJUSTMENT

FOR BALANCE

6 inches

4 - 12

below

waist

inches

above

 

 

ground

CONFIGURING YOUR UNIT

You can configure your unit using a trim- mer head for grass and light weeds, or a weed blade for cutting grass, weeds, and brush up to 1/2 inch in diameter. To assemble your unit, go to the section for

the desired configuration and follow the instructions.

ASSEMBLY INFORMATION - TRIMMER HEAD

TRIMMER

HEAD

NOTE: Remove the blade and metal shield before attaching the plastic shield and trimmer head. To remove blade, align hole in the dust cup with the hole in the side of the gearbox by rotating the blade. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while loosening the blade nut. Remove blade nut by turning clockwise. Remove the screwdriver. Remove both washers and blade. To remove metal shield, loosen and re-

move the four mounting screws. See AT- TACHING THE METALSHIELD and INSTALLATIONOF THE METAL BLADE for

illustrations. Be sure to store all parts and instructions for future use.

INSTALLATION OF THE TRIMMER

HEAD

NOTE: Before installing the trimmer head, make sure the dust cup and re- taining washer are positioned on the shaft of the gearbox, The retaining washer must be positioned with the raised section toward the gearbox,

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Brushcutter Attachment Sears, Roebuck and Co., I/817 WA, Hoffman Estates, IL Full ONE Year Warranty on Craftsman Brushcutter AttachmentAlways Wear Operator SafetyTransporting and Storage UNIT/MAINTENANCE SafetyFuel Safety Cutting SafetyInstalling Brushcutter AT- Tachment Carton ContentsHandlebar Assembly Lower Shoulder Strap Clamp Shoulder Strap AssemblyHead Configuring Your UnitAssembly Information Trimmer Head Installation of the TrimmerAttaching the Plastic Shield Assembly Information Weed BladeAttaching the Metal Shield Ightenevenlyandsecurelywith thehexwrenchprovided Installation of the Metal BladeOperating the Coupler Trimmer HeadTrimmer Shield Tube Release Installingoptional Attach MentUSE of Brushcutter ATTACH* Ment with Trimmer Head What Causes Blade Thrust When Blade Thrust OccursScalping MowingRecommended Cutting Position Line Replacement Maintenance ScheduleCare and Maintenance Task Blade MaintenanceSeasonal Storage Blade ReplacementReplacing the Cutting Head Sears, Roebuck and Co., 13/817 WA Hoffman Estates, IL Sears MAS Cercano EN LOS Estados UnidosADVERTENClA Zona de peligro DadvertenciaAdvertencia Utilice SiemDEL Aparato Seguridad CON EL CombusTible Mantenimiento SeguridadContenido DE LA Caja Transporte Y AlmacenamientoMontaje Base DE Abrazadera Installation DEL Mango Peligro Riesgo DE CortaInstalacionde LA Accesorio DEL Cortadora DE Malezas Precaucion AI instalar las accesoEXTREM0 CON EL Cabeza DE Motor Montaje DE LA Correa ParaAbrazadera Inferior DEL Correa Para Hombro HombroINFORMACI3N DE Montaje Cabezal DE Corte CONFIGURACI3N DEL AparatoPara Instalar EL Cabezal DE Corte Para Nstalar EL Cabezal DE Corte ManualmenteINFORMACI3N DE Montaje Cuchillas Papa Malezas Para Instalar EL Protector PlasticaMON.TAJE DE LA Cuchilla Metamca Como Remover EL Accesorio DEL Cortadora DE Malezas U Conozca SU Cortadora DE Malezas AccesorioOPERAClON DEL Acoplador Protector DE LA CuchillaMetodos DE Corte INSTALACI6NDEL AccesoriosInstacalin DEL Suspensor Cabezal DE CortePara Barter La punta de la linea La linea est metidaDentro del material CorrectaIncorrectaCausas DEL Rebote DE LA Cuchilla El Rebote de la La cuchilla si Cronograma DE MantenimientoTarea DE Cuidado Y Mantenimiento Mantenimiento DE LA CuchillaCambio DE LA Cuchilla Reemplazo DE LA Linea EN EL Cabezal DE Corte DE Lnea FijaUse siempre inea de recambio Craftsman Reemplazo DE LA Cabezal DE Corte4ADVERTENCIA Realice los si
Top Page Image Contents