Craftsman 358.792440 instruction manual Shoulder Strap Assembly, Lower Shoulder Strap Clamp

Page 6

NOTE:Thetubeclampbasehasfour

spacertabsattachedThesetabsare. providedtoadaptthisattachmentfor usewithpowerheadsthathave1"di- ameteruppertube(thetubeclampwill nottightendownsecurelyonthe1"di- ameteruppertubewithoutusingthese spacertabs)Thetabsmustbebroken. offcompletelybeforeuseandplaced overthescrewholesontheclampbase. Thesetabsarenotneededforpower- headswitha7/8"uppertube.

HANDLEBARCLAMPBASE SpacerTabs

SpacerTabs _

o °ai i° e rer ae

upper tube

_I

1.Place the tube clamp over the upper tube above the arrow on the safety decal.

2.Position the clamp base under the upper tube and align the tube clamp and clamp base screw holes (use spacer tabs between tube clamp and clamp base if necessary to se- cure clamp, i.e. for 1" diameter up- per tube).

Handlebar

POWERHEAD

END

4.Secure tube clamp by tightening screws with the hex wrench.

5.Position the handlebar as shown, ensuring the handlebar is posi- tioned on the handlebar clamp be- tween the two arrows on the han- dlebar decal.

6.Retighten handlebar byturning clamp knob clockwise until handle- bar is secure and stationary in clamp (clamp knob cannot be overtightened).

SHOULDER STRAP ASSEMBLY

_1_ WARNING:

Proper shoulder

strap and handlebar adjustments must be made with the engine completely stopped before using unit. The shoul- der strap clamp must be installed as shown above the handlebar on the up- per tube (powerhead end of unit).

NOTE: The lower shoulder strap clamp has two spacer tabs attached. These tabs are provided to adapt this attach- ment for use with powerheads that have a 1" diameter upper tube (the shoulder strap clamp will not tighten down se- curely on the 1" diameter upper tube without using these spacer tabs). The tabs must be broken off completely be- fore use and placed over the screw holes on the lower shoulder strap clamp. These tabs are not needed for power- heads with a 7/8" upper tube.

LOWER SHOULDER STRAP

CLAMP

Spacer Tabs_'r _

Handlebar Clamp between arrows on handlebar decal

Clam

Knob

ClampScrews

Arrow on

Safety Decal

ATTACHMENT END

3.Insert four screws into the screw holes.

.,dC_L.4--_ _- Spacer Tabs

I1_-_ positioned for use

on 1" diameter

upper tube

1, Place the upper shoulder strap clamp over the upper tube above the handlebar.

2.Position the lower shoulder strap clamp under the upper tube and align the upper and lower clamp screw holes (use spacer tabs be- tween upper and lower clamps if necessary to secure clamp, i.e. for 1" diameter upper tube).

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Brushcutter Attachment Full ONE Year Warranty on Craftsman Brushcutter Attachment Sears, Roebuck and Co., I/817 WA, Hoffman Estates, ILOperator Safety Always WearCutting Safety UNIT/MAINTENANCE SafetyFuel Safety Transporting and StorageCarton Contents Installing Brushcutter AT- TachmentHandlebar Assembly Shoulder Strap Assembly Lower Shoulder Strap ClampInstallation of the Trimmer Configuring Your UnitAssembly Information Trimmer Head HeadAssembly Information Weed Blade Attaching the Plastic ShieldAttaching the Metal Shield Installation of the Metal Blade Ightenevenlyandsecurelywith thehexwrenchprovidedTrimmer Head Operating the CouplerTrimmer Shield Installingoptional Attach Ment Tube ReleaseUSE of Brushcutter ATTACH* Ment with Trimmer Head Mowing When Blade Thrust OccursScalping What Causes Blade ThrustRecommended Cutting Position Blade Maintenance Maintenance ScheduleCare and Maintenance Task Line ReplacementBlade Replacement Seasonal StorageReplacing the Cutting Head Sears MAS Cercano EN LOS Estados Unidos Sears, Roebuck and Co., 13/817 WA Hoffman Estates, ILUtilice Siem DadvertenciaAdvertencia ADVERTENClA Zona de peligroMantenimiento Seguridad Seguridad CON EL CombusTible DEL AparatoTransporte Y Almacenamiento Contenido DE LA CajaMontaje DEL Cortadora DE Malezas Precaucion AI instalar las acceso Installation DEL Mango Peligro Riesgo DE CortaInstalacionde LA Accesorio Base DE AbrazaderaHombro Montaje DE LA Correa ParaAbrazadera Inferior DEL Correa Para Hombro EXTREM0 CON EL Cabeza DE MotorCONFIGURACI3N DEL Aparato INFORMACI3N DE Montaje Cabezal DE CortePara Instalar EL Cabezal DE Corte Para Instalar EL Protector Plastica ManualmenteINFORMACI3N DE Montaje Cuchillas Papa Malezas Para Nstalar EL Cabezal DE CorteMON.TAJE DE LA Cuchilla Metamca Protector DE LA Cuchilla Conozca SU Cortadora DE Malezas AccesorioOPERAClON DEL Acoplador Como Remover EL Accesorio DEL Cortadora DE Malezas UCabezal DE Corte INSTALACI6NDEL AccesoriosInstacalin DEL Suspensor Metodos DE CorteCorrectaIncorrecta La punta de la linea La linea est metidaDentro del material Para BarterCausas DEL Rebote DE LA Cuchilla El Rebote de la Mantenimiento DE LA Cuchilla Cronograma DE MantenimientoTarea DE Cuidado Y Mantenimiento La cuchilla siReemplazo DE LA Cabezal DE Corte Reemplazo DE LA Linea EN EL Cabezal DE Corte DE Lnea FijaUse siempre inea de recambio Craftsman Cambio DE LA Cuchilla4ADVERTENCIA Realice los si
Top Page Image Contents