TROUBLE SHOOTING
SYMPTOM
start or will run
only for a few
seconds after Starting.
CAUSE_ •
II, II
1.Fuel tank empty.
2.Engine flooded.
. Spark p!ug not firing.
4.Fuel not reachingcarburetor.
5.Carburetorrequiresadjustment.
6.None oftheabove.
REMEDY
,, .,, | == |
1, Fill tank with correct fue! mixture
2, See "Starting Instructions."
3.Install new plug/check ignition system,
. Clean fuel filter; inspect fue! line.
5.See "Carburetor Adjustments."
6.Contact yovr Sears Service Center/Dept,
,,,,,,,,,,
Engine will not idle properly.
Engine will not accelerate,lacks
power, or dies under a load.
Engine smokes excessively.
Engine runs hot.
Cutting Head stops under a load or does not turn
when engine is
accelerated: :
i i,J JL
Line doesnot advance or breaks
while cutting. _ _ :
1. Carburetor requires adjustment
2.None of the aboVe.
1.Air filter dirty,
2, Spark plug fouled.
3. Carburetor requires adjustment,
4.Muffler outlets plugged, 5_ None of the above.
........, ....... ,,,,, ,,, ....
1.Air filter dirty.
2.Fuel mixture incorrect.
3, Carburetor requires adjustment.
. Fuel mixture incorrect.
2. Carburetor requires :adjustment.
3.Spark plug incorrect.
4.None of the above.
....................
. Drive shaft broken.
2. Drive shaft not engaged.
,, ,, i,,,i,,,,,,,,,,,,,,,,,,,,i,,,
i.Line improperlyroutedinhead.
2.Line improperlywound onto spool.
3.Line sizeincorrect.
1.See "Carburetor Adjustments,"
2.Contact your Sears Service Center/Dept,
, ,,..,., | ,,,,, | • | ,.... |
1.Clean'or replace air filter.
2.Clean or replace spark plug and
3.See "Carburetor Adjustments."
4.Contact your Sears Service Center/Dept.
5.i Contact y0ur Sears Service Center/Dept,
,i ............
1.Clean or replace air filter.
2.See "Fueling Your Unit."
3.See "Carburetor Adjustments,"
1.See "Fueling Your Unit."
2.See "Carburetor Adjustments."
3.Replace with correct plug.
4.Contact your Sears Service Center/Dept.
p .... | i,,,,u,,,,,, |
1, Replace drive shaft. 2.. See "Assembly".
i. Remove coven Check linerouting.
2.Rewind linetightlyand evenly.
3.Use only.080"(2ram)diameterSearsLaser Line.
4.Too little line outside head.
5.Dirt accumulated on cover
i,,. | ...... ,.,,, | ill IIMH |
Line welds on spool. 1. Line size incorrect.
2.Crowding lineagainstmaterialbeing cut.
3.Cuttingat higherspeedthan necessary.
, = | , ,,,m |
4.Remove cover.Pull4,'oflinetooutside._
5.Clean
,HH | .... | '"' |
1.Use only.080"(2ram)diameterSearsLaser
Line.
2.Cut witht_ of line.
3.Reduce cutting speed.
Line releases
continuously.
Line usage is
excesslve.
I. Tap Button engaged. | 1. | Remove and clean Tap Button.'- | - | ||
2. Tap buttonknocked out ofhub. | 2. | See "Installing | Spool | w/Line." |
|
............................... | , ,L |
|
|
|
|
I. Line sizeincorrect. | 1, | Use only .080" | (2mm) | diameter | Sears Laser |
Line.
. Cuttingathigh speed around hard objects.2. Reduce speedaround hard objects. 3, Crowding lineagainstmaterialbeingcut. 3. Cut with tipofline.
, ,,± i1,,i,,1,
Line | pulls back | @ Too littlelineoutsideofhead. |
into | head. |
|
•Remove cover.Pull4" (10cm) oflineto outside.
27