Tiger Products Co., Ltd TWR-180, TWR-120 manual Straighten or Weld on Blades Since this will Likely

Page 12
(SGM-6)
(SGM-5)

SAFETY

SAFETY

WARNING!

WARNING!

Extreme care should be taken when operating near loose objects such as gravel, rocks, wire, and other debris. Inspect the area before mowing. Foreign objects should be removed from the site to prevent machine damage and/or bodily injury or even death. Any objects that cannot be removed must be clearly marked and carefully avoided by the operator. Stop mowing immediately if blades strike a foreign object. Repair all damage and make certain rotor or blade carrier is balanced before resuming mowing.

Many varied objects, such as wire, cable, rope, or chains, can become entangled in the operating parts of the mower head. These items could then swing outside the housing at greater velocities than the blades. Such a situation is extremely hazardous and could result in serious injury or even death. Inspect the cutting area for such objects before mowing. Remove any like object from the site. Never allow the cutting blades to contact such items.

WARNING! Mow at the speed that you can safely operate and control the tractor and mower. Safe mowing speed depends on terrain condition and grass type, density, and height of cut. Normal ground speed range is from 0 to 5 mph. Use slow mowing speeds when operating on or near steep slopes, ditches, drop-offs, overhead obstructions, power lines, or when

 

debris and foreign objects are to be avoided. (SGM-7)

WARNING!

Avoid mowing in reverse direction when possible. Check to make sure

 

there are no persons behind the mower and use extreme care when

 

mowing in reverse. Mow only at a slow ground speed where you can safely

 

operate and control the tractor and mower. Never mow an area that you

 

have not inspected and removed debris or foreign material. (SGM-8)

WARNING!

Do not put hands or feet under mower decks. Blade Contact can result

 

serious injury or even death. Stay away until all motion has stopped and

 

the decks are securely blocked up. (SGM-9)

DANGER!

Replace bent or broken blade with new blades. NEVER ATTEMPT TO

 

STRAIGHTEN OR WELD ON BLADES SINCE THIS WILL LIKELY

 

CRACK OR OTHERWISE DAMAGE THE BLADE WITH SUBSE-

 

QUENT FAILURE AND POSSIBLE SERIOUS INJURY FROM THROWN

 

BLADES. (SGM-10)

WARNING!

Mow only in conditions where you have clear visibilities in daylight or

 

with adequate artificial lighting. Never mow in darkness or foggy

 

conditions where you cannot clearly see at least 100 yards in front

 

and to the sides of the Tractor and Mower. Make sure that you can

 

clearly see and identify passersby, steep slopes, ditches, drop-offs,

 

overhead obstructions, power lines, gas lines, debris, and foreign

 

objects. If you do not have clear and safe visibility discontinue

 

mowing. (SGM-11)

WARNING!

Mow at the speed that you can safely operate and control the Tractor

and Mower. Safe mowing speed depends on terrain condition and grass type, density, and height of cut. Normal ground speed range is from 0 to 5 mph. Use slow mowing speeds when operating on or near steep slopes, ditches, drop-offs, overhead obstructions, power

lines, gas lines or when debris, and foreign objects are to be avoided.

(SGM-12)

Safety Section 1-8

TWR-180 / TWR-120 12/04

 

 

 

© 2004 Alamo Group Inc.

 

Page 11 Page 13
Image 12
Page 11 Page 13
Contents TWR-180 TWR-120 To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety SafetySafety SG-10 Abide by the following rules Keep Away from Rotating Elements to prevent entanglement Possible serious injury or deathImplement, an operator on prescription or over-the-counter Straighten or Weld on Blades Since this will Likely Stop Mowing if Passersby are Within 100 Yards Unless Wait a minute...Save a life Or even death. STI-4 Parts InformationSafety QTY Description TWR-180 / TWR-120 12/04 Safety Section See Inside Fornt Cover Serial Plate Safety On 10 Units Only TWR-180 / TWR-120 12/04 Safety Section TWR-180 / TWR-120 12/04 Safety Section Safety Federal Laws and Regulations Page Introduction Section Introduction IntroductionAssembly Section Assembly GeneralConnection to Tractor Wing Lift Spacer Plates Adjustable Skids Center Wheel Standard Spacer PlatesDriveline Shield Chains Laminated TiresCenter Section Wheel Standards Transport Light Kit Hydraulic Phasing Cylinders Rephasing GrooveSpool Valve Kit Operation Section Operation Operation Tiger Rotary Mower Operation InstructionsOperation Medias de seguridad. SG-3Mower Standard Equipment And Specifications Operator Requirements Tractor and Implement. Drugs and alcohol will affect anOperator’s alertness and coordination and therefore affect Tractor Safety Devices Tractor RequirementsTractor Requirements and Capabilities Rops and Seat BeltTractor Horsepower Front End WeightDrawbar Tractor HydraulicsPower Take Off PTO Tire SpacingTire Spacing Minimum Width Getting on and OFF the Tractor Boarding the TractorDismounting the Tractor Falling off can result in serious injury or death . SG-10Starting the Tractor Operation Connecting the Mower to the Tractor Safety Tow ChainSetting the Mower Hydraulic Line SupportHydraulic Cylinder Priming Setting Cutting Height Setting Deck PitchDriveline Attachment Driveline Length CheckBottoming Out Check Procedure Engagement Check ProcedureDriveline in maximum compressed position CV Driveline Maximum Angle Check Procedure Constant Velocity CV DrivelinePRE-OPERATION Inspection and Service Entanglement, injury or death. SRM-3Tractor Pre-Operation Inspection/Service Mower Pre-Operation Inspection/ServiceOperation Operation Driving the Tractor and Mower Traffic around you and watch out for the other guy. SG-19Brake and Differential Lock Setting Starting the TractorOperating the Mower Wings Transport PositionDriving the Tractor and Mower Crossing Ditches and Steep Inclines Operating the Tractor and Mower Foreign Debris HazardsResuming mowing. SGM-5 Bystander/Passersby Precautions Stop Mowing if Passersby are Within 100 Yards UnlessEngaging the Power Take Off PTO PTO RPM and Ground SpeedFrom the blades. SRM-7 Operating the Mower Mowing . S G M Operation Disconnecting the Mower from the Tractor Mower Storage Transporting the Tractor and Mower Tires and WheelsTransporting on Public Roadways OperationOperation Hauling the Tractor and Mower Trouble Shooting Guide Maintenance Section Maintenance DisassemblySlip Clutches Maintenance Nuts and Bolts HydraulicsHubs and Spindles Tires Blade Installation Blade ServicingBlade Removal Blade Carrier Installation Blade Carrier RemovalMaintenance Grease Schedule Cutter Frame StorageWarranty Information TigerONE Last Word TWR-180-/TWR-120 12/04 C314TG010C

TWR-120, TWR-180 specifications

Tiger Products Co., Ltd has established itself as a leader in the manufacturing of advanced welding and cutting equipment. Among its innovative offerings are the TWR-180 and TWR-120 models, which have quickly gained attention for their superior technology, robust features, and reliable performance.

The TWR-180 is designed for high-capacity operations, featuring an impressive welding output that makes it suitable for a variety of applications in industries such as automotive, construction, and heavy machinery. One of the standout features of the TWR-180 is its dual pulse technology, which allows for precise control over welding depth and heat input. This technology not only enhances the quality of welds but also minimizes material distortion, making it ideal for intricate designs and complex assemblies.

In addition to its advanced welding capabilities, the TWR-180 includes digital control systems that provide operators with real-time feedback on welding parameters. This user-friendly interface is complemented by programmable memory settings that allow users to save specific welding configurations, thereby enhancing productivity. The TWR-180 is also equipped with a high-efficiency cooling system that prevents overheating during extended use, ensuring that the equipment remains operational without interruptions.

On the other hand, the TWR-120 is specifically tailored for smaller-scale projects while maintaining professional-grade performance. The compact design of the TWR-120 makes it easy to transport and set up, which is vital for on-site applications. It features a simplified control panel that allows for quick adjustments, making it accessible for operators with varying levels of expertise.

Despite its smaller size, the TWR-120 does not compromise on power; it is equipped with innovative inverter technology that maximizes energy efficiency while providing stable output across various welding tasks. This model is particularly appealing to small businesses and workshops looking for a reliable yet versatile welding solution.

Both the TWR-180 and TWR-120 utilize advanced arc stabilization technologies that enhance the quality of the weld, reduce spatter, and improve overall efficiency. These characteristics, combined with exceptional durability and low maintenance requirements, highlight Tiger Products Co., Ltd's commitment to delivering top-tier equipment that meets the needs of diverse industries.

In summary, the TWR-180 and TWR-120 reflect Tiger Products Co., Ltd’s dedication to innovation, quality, and user-centric design. Whether for high-capacity operations or smaller-scale tasks, these models provide exceptional performance and reliability that set them apart in the competitive welding equipment market.
Top Page Image Contents