Tiger Products Co., Ltd TWR-120, TWR-180 manual Or even death. STI-4, Parts Information

Page 15
(SG-18)
(STI-6)

SAFETY

WARNING! Never unhitch without using the Tongue Jack. The Tongue is very heavy. Attempting to lift the Tongue without using the Tongue Jack could cause strains or other injury. Allowing the tongue to fall suddenly and unexpectedly could result in crushing injury. Use the Tongue Jack for lifting the mower only. Overloading the Tongue Jack can cause failure with possible serious bodily injury

CAUTION!

WARNING!

or even death. (STI-4)

On a fully-assembled unit, do not remove the Wing Retaining Strap until hoses are attached to the tractor and the Wing Cylinders are filled with oil. Lower the Wings slowly and carefully. Keep bystand- ers away during operations. (STI-5)

Only tow the Implement behind a properly sized and equipped Tractor which exceeds the weight of the Implement by at least 20%. DO NOT tow the Implement behind a truck or other type of vehicle. Never tow the Implement and another Implement connected in tandem. Never tow the Implement at speeds over 20 MPH.

SAFETY

WARNING! Follow these guidelines to reduce the risk of equipment and grass fires while operating, servicing, and repairing the Mower and Tractor: -Equip the Tractor with a fire extinguisher in an accesible location. -Do Not operate the Mower on a Tractor with an underframe exhaust. -Do Not smoke or have an open flame near the Mower and Tractor. -Do Not drive into burning debris or freshly burnt areas.

-Ensure slip clutches are properly adjusted to prevent excessive slippage and plate heating.

-Never allow clippings or debris to collect near drivelines, slip clutches, and gearboxes. Periodically shut down the Tractor and Mower and

PARTS INFORMATION

Tiger mowers use balanced and matched system components for blade carriers, blades, cuttershafts, knives, knife hangers, rollers, drivetrain components, and bearings. These parts are made and tested to Tiger specifications. Non-genuine "will fit" parts do not consistently meet these specifications. The use of “will fit” parts may reduce mower performance, void mower warranties, and present a safety hazard. Use genuine Tiger mower parts for economy and safety.

(SPTM-1)

SEE YOUR TIGER DEALER

In addition to the design and configuration of this Implement, including Safety Signs and Safety Equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of personnel involved in the operation, transport, maintenance, and storage of the machine. Refer also to Safety Messages and operation instruction in each of the appropriate sections of the Tractor and Equipment Manuals. Pay close attention to the Safety Signs affixed to the Tractor and Equipment.

TWR-180 / TWR-120 12/04

Safety Section 1-11

 

 

 

© 2004 Alamo Group Inc.

 

Page 14 Page 16
Image 15
Page 14 Page 16
Contents TWR-180 TWR-120 To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety SafetySafety SG-10 Abide by the following rules Possible serious injury or death Keep Away from Rotating Elements to prevent entanglementImplement, an operator on prescription or over-the-counter Straighten or Weld on Blades Since this will Likely Stop Mowing if Passersby are Within 100 Yards Unless Wait a minute...Save a life Parts Information Or even death. STI-4Safety QTY Description TWR-180 / TWR-120 12/04 Safety Section See Inside Fornt Cover Serial Plate Safety On 10 Units Only TWR-180 / TWR-120 12/04 Safety Section TWR-180 / TWR-120 12/04 Safety Section Safety Federal Laws and Regulations Page Introduction Section Introduction IntroductionAssembly Section Assembly GeneralConnection to Tractor Wing Lift Spacer Plates Laminated Tires Adjustable SkidsCenter Wheel Standard Spacer Plates Driveline Shield ChainsCenter Section Wheel Standards Transport Light Kit Rephasing Groove Hydraulic Phasing CylindersSpool Valve Kit Operation Section Operation Tiger Rotary Mower Operation Instructions OperationMedias de seguridad. SG-3 OperationMower Standard Equipment And Specifications Operator Requirements Tractor and Implement. Drugs and alcohol will affect anOperator’s alertness and coordination and therefore affect Rops and Seat Belt Tractor Safety DevicesTractor Requirements Tractor Requirements and CapabilitiesTractor Hydraulics Tractor HorsepowerFront End Weight DrawbarPower Take Off PTO Tire SpacingTire Spacing Minimum Width Falling off can result in serious injury or death . SG-10 Getting on and OFF the TractorBoarding the Tractor Dismounting the TractorStarting the Tractor Safety Tow Chain Operation Connecting the Mower to the TractorSetting the Mower Hydraulic Line SupportHydraulic Cylinder Priming Setting Deck Pitch Setting Cutting HeightDriveline Length Check Driveline AttachmentBottoming Out Check Procedure Engagement Check ProcedureDriveline in maximum compressed position Constant Velocity CV Driveline CV Driveline Maximum Angle Check ProcedureEntanglement, injury or death. SRM-3 PRE-OPERATION Inspection and ServiceMower Pre-Operation Inspection/Service Tractor Pre-Operation Inspection/ServiceOperation Operation Traffic around you and watch out for the other guy. SG-19 Driving the Tractor and MowerStarting the Tractor Brake and Differential Lock SettingTransport Position Operating the Mower WingsDriving the Tractor and Mower Crossing Ditches and Steep Inclines Operating the Tractor and Mower Foreign Debris HazardsResuming mowing. SGM-5 Stop Mowing if Passersby are Within 100 Yards Unless Bystander/Passersby PrecautionsEngaging the Power Take Off PTO PTO RPM and Ground SpeedFrom the blades. SRM-7 Operating the Mower Mowing . S G M Operation Disconnecting the Mower from the Tractor Mower Storage Tires and Wheels Transporting the Tractor and MowerOperation Transporting on Public RoadwaysOperation Hauling the Tractor and Mower Trouble Shooting Guide Maintenance Section Maintenance DisassemblySlip Clutches Maintenance Hydraulics Nuts and BoltsHubs and Spindles Tires Blade Installation Blade ServicingBlade Removal Blade Carrier Removal Blade Carrier InstallationMaintenance Grease Schedule Storage Cutter FrameTiger Warranty InformationONE Last Word TWR-180-/TWR-120 12/04 C314TG010C

TWR-120, TWR-180 specifications

Tiger Products Co., Ltd has established itself as a leader in the manufacturing of advanced welding and cutting equipment. Among its innovative offerings are the TWR-180 and TWR-120 models, which have quickly gained attention for their superior technology, robust features, and reliable performance.

The TWR-180 is designed for high-capacity operations, featuring an impressive welding output that makes it suitable for a variety of applications in industries such as automotive, construction, and heavy machinery. One of the standout features of the TWR-180 is its dual pulse technology, which allows for precise control over welding depth and heat input. This technology not only enhances the quality of welds but also minimizes material distortion, making it ideal for intricate designs and complex assemblies.

In addition to its advanced welding capabilities, the TWR-180 includes digital control systems that provide operators with real-time feedback on welding parameters. This user-friendly interface is complemented by programmable memory settings that allow users to save specific welding configurations, thereby enhancing productivity. The TWR-180 is also equipped with a high-efficiency cooling system that prevents overheating during extended use, ensuring that the equipment remains operational without interruptions.

On the other hand, the TWR-120 is specifically tailored for smaller-scale projects while maintaining professional-grade performance. The compact design of the TWR-120 makes it easy to transport and set up, which is vital for on-site applications. It features a simplified control panel that allows for quick adjustments, making it accessible for operators with varying levels of expertise.

Despite its smaller size, the TWR-120 does not compromise on power; it is equipped with innovative inverter technology that maximizes energy efficiency while providing stable output across various welding tasks. This model is particularly appealing to small businesses and workshops looking for a reliable yet versatile welding solution.

Both the TWR-180 and TWR-120 utilize advanced arc stabilization technologies that enhance the quality of the weld, reduce spatter, and improve overall efficiency. These characteristics, combined with exceptional durability and low maintenance requirements, highlight Tiger Products Co., Ltd's commitment to delivering top-tier equipment that meets the needs of diverse industries.

In summary, the TWR-180 and TWR-120 reflect Tiger Products Co., Ltd’s dedication to innovation, quality, and user-centric design. Whether for high-capacity operations or smaller-scale tasks, these models provide exceptional performance and reliability that set them apart in the competitive welding equipment market.
Top Page Image Contents