Tiger Products Co., Ltd TWR-180, TWR-120 manual Constant Velocity CV Driveline

Page 50
(SRM-4)

OPERATION

OPERATION

7.2 Constant Velocity (CV) Driveline

For mowers equipped with a Constant Velocity (CV) driveline, the maximum turning angle between the tractor and mower must be determined to ensure the joint angle does not over-extend which can cause CV joint damage. Constant Velocity joints enable the driveline to operate smoothly with no vibrations and clattering at angles up to 70°. Angles greater than 80° can result in mechanical damage to the CV joint and mower driveline.

The Constant Velocity joint must be lubricated every 8 hours of operation as specified in the Maintenance Section. Failure to properly lubricate the joint will result in accelerated wear and joint component failure.

CV Driveline Maximum Angle Check Procedure

1.With the mower attached to the tractor and the driveline disconnected from the tractor PTO stub make a hard left turn until there is approximately a 1" clearance between the left rear tractor tire and mower frame or tongue.

2.Stop and completely shut down the tractor. Place the tractor in Park and apply the Parking Brake before dismounting.

3.Check the CV joint at this maximum turning radius by holding the driveline yoke above the PTO shaft and then angle the CV joint to its maximum angle. A minimum difference of 10 degrees between the center line of the yoke and the PTO shaft must be maintained to ensure the joint will not be over angled. If the joint cannot be angled at least 10°, there is a potential problem of over-angling the joint while making sharp turns.

4.Solutions: To ensure the joint is not damaged, check the following:

-Check the drawbar length to ensure that it is at the proper length for the RPM speed of the mower. -Move the tractor rear tires wider apart to limit the tractor turning radius.

-Position the mower at multiple angles and perform the above procedure. Determine the sharpest turning radius that maintains a safe operating angle and note this position to the operator.

10 DEG.

80 DEG.

80 DEG.

CONSTANT VELOCITY JOINT-MAXIMUM ANGLE CHECK

DANGER! Do not turn so sharp or lift mower so high to produce a severe "knocking" of the Driveline which will cause accelerated wear and breakage of drive train components and could result in possible injury from the separated Driveline sections.

TWR-180 / TWR-120 12/04

Operation Section 4-16

© 2004 Alamo Group Inc.

Page 49 Page 51
Image 50
Page 49 Page 51
Contents TWR-180 TWR-120 To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety SafetySafety SG-10 Abide by the following rules Keep Away from Rotating Elements to prevent entanglement Possible serious injury or deathImplement, an operator on prescription or over-the-counter Straighten or Weld on Blades Since this will Likely Stop Mowing if Passersby are Within 100 Yards Unless Wait a minute...Save a life Or even death. STI-4 Parts InformationSafety QTY Description TWR-180 / TWR-120 12/04 Safety Section See Inside Fornt Cover Serial Plate Safety On 10 Units Only TWR-180 / TWR-120 12/04 Safety Section TWR-180 / TWR-120 12/04 Safety Section Safety Federal Laws and Regulations Page Introduction Section Introduction IntroductionAssembly Section Connection to Tractor AssemblyGeneral Wing Lift Spacer Plates Driveline Shield Chains Adjustable SkidsCenter Wheel Standard Spacer Plates Laminated TiresCenter Section Wheel Standards Transport Light Kit Hydraulic Phasing Cylinders Rephasing GrooveSpool Valve Kit Operation Section Operation Operation Tiger Rotary Mower Operation InstructionsOperation Medias de seguridad. SG-3Mower Standard Equipment And Specifications Operator’s alertness and coordination and therefore affect Operator RequirementsTractor and Implement. Drugs and alcohol will affect an Tractor Requirements and Capabilities Tractor Safety DevicesTractor Requirements Rops and Seat BeltDrawbar Tractor HorsepowerFront End Weight Tractor HydraulicsTire Spacing Minimum Width Power Take Off PTOTire Spacing Dismounting the Tractor Getting on and OFF the TractorBoarding the Tractor Falling off can result in serious injury or death . SG-10Starting the Tractor Operation Connecting the Mower to the Tractor Safety Tow ChainHydraulic Cylinder Priming Setting the MowerHydraulic Line Support Setting Cutting Height Setting Deck PitchDriveline Attachment Driveline Length CheckDriveline in maximum compressed position Bottoming Out Check ProcedureEngagement Check Procedure CV Driveline Maximum Angle Check Procedure Constant Velocity CV DrivelinePRE-OPERATION Inspection and Service Entanglement, injury or death. SRM-3Tractor Pre-Operation Inspection/Service Mower Pre-Operation Inspection/ServiceOperation Operation Driving the Tractor and Mower Traffic around you and watch out for the other guy. SG-19Brake and Differential Lock Setting Starting the TractorOperating the Mower Wings Transport PositionDriving the Tractor and Mower Crossing Ditches and Steep Inclines Resuming mowing. SGM-5 Operating the Tractor and MowerForeign Debris Hazards Bystander/Passersby Precautions Stop Mowing if Passersby are Within 100 Yards UnlessFrom the blades. SRM-7 Engaging the Power Take Off PTOPTO RPM and Ground Speed Operating the Mower Mowing . S G M Operation Disconnecting the Mower from the Tractor Mower Storage Transporting the Tractor and Mower Tires and WheelsTransporting on Public Roadways OperationOperation Hauling the Tractor and Mower Trouble Shooting Guide Maintenance Section Slip Clutches MaintenanceDisassembly Maintenance Nuts and Bolts HydraulicsHubs and Spindles Tires Blade Removal Blade InstallationBlade Servicing Blade Carrier Installation Blade Carrier RemovalMaintenance Grease Schedule Cutter Frame StorageWarranty Information TigerONE Last Word TWR-180-/TWR-120 12/04 C314TG010C

TWR-120, TWR-180 specifications

Tiger Products Co., Ltd has established itself as a leader in the manufacturing of advanced welding and cutting equipment. Among its innovative offerings are the TWR-180 and TWR-120 models, which have quickly gained attention for their superior technology, robust features, and reliable performance.

The TWR-180 is designed for high-capacity operations, featuring an impressive welding output that makes it suitable for a variety of applications in industries such as automotive, construction, and heavy machinery. One of the standout features of the TWR-180 is its dual pulse technology, which allows for precise control over welding depth and heat input. This technology not only enhances the quality of welds but also minimizes material distortion, making it ideal for intricate designs and complex assemblies.

In addition to its advanced welding capabilities, the TWR-180 includes digital control systems that provide operators with real-time feedback on welding parameters. This user-friendly interface is complemented by programmable memory settings that allow users to save specific welding configurations, thereby enhancing productivity. The TWR-180 is also equipped with a high-efficiency cooling system that prevents overheating during extended use, ensuring that the equipment remains operational without interruptions.

On the other hand, the TWR-120 is specifically tailored for smaller-scale projects while maintaining professional-grade performance. The compact design of the TWR-120 makes it easy to transport and set up, which is vital for on-site applications. It features a simplified control panel that allows for quick adjustments, making it accessible for operators with varying levels of expertise.

Despite its smaller size, the TWR-120 does not compromise on power; it is equipped with innovative inverter technology that maximizes energy efficiency while providing stable output across various welding tasks. This model is particularly appealing to small businesses and workshops looking for a reliable yet versatile welding solution.

Both the TWR-180 and TWR-120 utilize advanced arc stabilization technologies that enhance the quality of the weld, reduce spatter, and improve overall efficiency. These characteristics, combined with exceptional durability and low maintenance requirements, highlight Tiger Products Co., Ltd's commitment to delivering top-tier equipment that meets the needs of diverse industries.

In summary, the TWR-180 and TWR-120 reflect Tiger Products Co., Ltd’s dedication to innovation, quality, and user-centric design. Whether for high-capacity operations or smaller-scale tasks, these models provide exceptional performance and reliability that set them apart in the competitive welding equipment market.
Top Page Image Contents