Tiger Products Co., Ltd TWR-120, TWR-180 Stop Mowing if Passersby are Within 100 Yards Unless

Page 13
(S3PT-1)
(SGM-13)

SAFETY

WARNING!

DANGER!

Avoid mowing in the reverse direction when possible. Check to make sure there are no persons behind the mower and use extreme care when mowing in reverse. Mow only at a slow ground speed where you can safely operate and control the Tractor and Mower. Never mow an area in the reverse direction that you have not inspected and removed debris or foreign material.

Rotary Mowers are capable under adverse conditions of throwing objects for great distances (100 yards or more) and causing serious injury or death. Follow

safetymessagescarefully

SAFETY

STOP MOWING IF PASSERSBY ARE WITHIN 100 YARDS UNLESS:

-Front and Rear Deflectors, Chain Guards, or Bands are installed and in good, workable condition;

-Mower sections or Wings are running close to and parallel to the ground without exposed Blades;

-Passersby are outside the existing thrown-object zone;

-All areas have been thoroughly inspected and all foreign material such as rocks, cans, glass, and general debris has been removed.

NOTE: Where there are grass and weeds high enough to hide debris

that could be struck by the blades, the area should be: inspected and large debris removed, mowed at an intermediate height, inspected, closely with any remaining debris being removed, and mowed again at desired final height. (This will also reduce power requiredto mow, reduce wear and tear on the Mower drivetrain, spread cut material better, eliminate streaking, and make the final cut more uniform.)

(SRM-1)

DANGER! Always disconnect the main PTO Driveline from the Tractor before performing service on the Mower. Never work on the Mower with the tractor PTO driveline connected and running. Blades or Drivelines could turn without warning and cause immediate entanglement, injury or death.

(SRM-3)

DANGER!

WARNING!

Do not turn so sharp or lift mower so high to produce a severe "knocking" of the Driveline which will cause accelerated wear and breakage of drive train components and could result inpossible injury from the separated Driveline sections. (SRM-4)

Do not let the Blades turn when the Mower Deck is raised for any reason, including clearance or for turning. Raising the Mower deck exposes the Cutting Blades which creates a potentially serious hazard and could cause serious injury or even death from objects thrown from the Blades. (SRM-7)

WARNING! Never leave Tractor and Implemented unattended while the implement is in the lifted position. Accidental operation of lifting lever or a hydraulic failure may cause sudden drop of unit with injury or death by crushing. To properly park the implement when disconnecting it from the tractor, lower the stand and put the retaining pin securely in place, or put a secure support under the A-Frame. Lower the implement carefully to the ground. Do not put hands or feet under lifted components.

TWR-180 / TWR-120 12/04

Safety Section 1-9

 

 

 

© 2004 Alamo Group Inc.

 

Image 13
Contents TWR-180 TWR-120 To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety SafetySafety SG-10 Abide by the following rules Possible serious injury or death Keep Away from Rotating Elements to prevent entanglementImplement, an operator on prescription or over-the-counter Straighten or Weld on Blades Since this will Likely Stop Mowing if Passersby are Within 100 Yards Unless Wait a minute...Save a life Parts Information Or even death. STI-4Safety QTY Description TWR-180 / TWR-120 12/04 Safety Section See Inside Fornt Cover Serial Plate Safety On 10 Units Only TWR-180 / TWR-120 12/04 Safety Section TWR-180 / TWR-120 12/04 Safety Section Safety Federal Laws and Regulations Page Introduction Section Introduction IntroductionAssembly Section General AssemblyConnection to Tractor Wing Lift Spacer Plates Center Wheel Standard Spacer Plates Adjustable SkidsDriveline Shield Chains Laminated TiresCenter Section Wheel Standards Transport Light Kit Rephasing Groove Hydraulic Phasing CylindersSpool Valve Kit Operation Section Operation Tiger Rotary Mower Operation Instructions OperationMedias de seguridad. SG-3 OperationMower Standard Equipment And Specifications Tractor and Implement. Drugs and alcohol will affect an Operator RequirementsOperator’s alertness and coordination and therefore affect Tractor Requirements Tractor Safety DevicesTractor Requirements and Capabilities Rops and Seat BeltFront End Weight Tractor HorsepowerDrawbar Tractor HydraulicsTire Spacing Power Take Off PTOTire Spacing Minimum Width Boarding the Tractor Getting on and OFF the TractorDismounting the Tractor Falling off can result in serious injury or death . SG-10Starting the Tractor Safety Tow Chain Operation Connecting the Mower to the TractorHydraulic Line Support Setting the MowerHydraulic Cylinder Priming Setting Deck Pitch Setting Cutting HeightDriveline Length Check Driveline AttachmentEngagement Check Procedure Bottoming Out Check ProcedureDriveline in maximum compressed position Constant Velocity CV Driveline CV Driveline Maximum Angle Check ProcedureEntanglement, injury or death. SRM-3 PRE-OPERATION Inspection and ServiceMower Pre-Operation Inspection/Service Tractor Pre-Operation Inspection/ServiceOperation Operation Traffic around you and watch out for the other guy. SG-19 Driving the Tractor and MowerStarting the Tractor Brake and Differential Lock SettingTransport Position Operating the Mower WingsDriving the Tractor and Mower Crossing Ditches and Steep Inclines Foreign Debris Hazards Operating the Tractor and MowerResuming mowing. SGM-5 Stop Mowing if Passersby are Within 100 Yards Unless Bystander/Passersby PrecautionsPTO RPM and Ground Speed Engaging the Power Take Off PTOFrom the blades. SRM-7 Operating the Mower Mowing . S G M Operation Disconnecting the Mower from the Tractor Mower Storage Tires and Wheels Transporting the Tractor and MowerOperation Transporting on Public RoadwaysOperation Hauling the Tractor and Mower Trouble Shooting Guide Maintenance Section Disassembly MaintenanceSlip Clutches Maintenance Hydraulics Nuts and BoltsHubs and Spindles Tires Blade Servicing Blade InstallationBlade Removal Blade Carrier Removal Blade Carrier InstallationMaintenance Grease Schedule Storage Cutter FrameTiger Warranty InformationONE Last Word TWR-180-/TWR-120 12/04 C314TG010C

TWR-120, TWR-180 specifications

Tiger Products Co., Ltd has established itself as a leader in the manufacturing of advanced welding and cutting equipment. Among its innovative offerings are the TWR-180 and TWR-120 models, which have quickly gained attention for their superior technology, robust features, and reliable performance.

The TWR-180 is designed for high-capacity operations, featuring an impressive welding output that makes it suitable for a variety of applications in industries such as automotive, construction, and heavy machinery. One of the standout features of the TWR-180 is its dual pulse technology, which allows for precise control over welding depth and heat input. This technology not only enhances the quality of welds but also minimizes material distortion, making it ideal for intricate designs and complex assemblies.

In addition to its advanced welding capabilities, the TWR-180 includes digital control systems that provide operators with real-time feedback on welding parameters. This user-friendly interface is complemented by programmable memory settings that allow users to save specific welding configurations, thereby enhancing productivity. The TWR-180 is also equipped with a high-efficiency cooling system that prevents overheating during extended use, ensuring that the equipment remains operational without interruptions.

On the other hand, the TWR-120 is specifically tailored for smaller-scale projects while maintaining professional-grade performance. The compact design of the TWR-120 makes it easy to transport and set up, which is vital for on-site applications. It features a simplified control panel that allows for quick adjustments, making it accessible for operators with varying levels of expertise.

Despite its smaller size, the TWR-120 does not compromise on power; it is equipped with innovative inverter technology that maximizes energy efficiency while providing stable output across various welding tasks. This model is particularly appealing to small businesses and workshops looking for a reliable yet versatile welding solution.

Both the TWR-180 and TWR-120 utilize advanced arc stabilization technologies that enhance the quality of the weld, reduce spatter, and improve overall efficiency. These characteristics, combined with exceptional durability and low maintenance requirements, highlight Tiger Products Co., Ltd's commitment to delivering top-tier equipment that meets the needs of diverse industries.

In summary, the TWR-180 and TWR-120 reflect Tiger Products Co., Ltd’s dedication to innovation, quality, and user-centric design. Whether for high-capacity operations or smaller-scale tasks, these models provide exceptional performance and reliability that set them apart in the competitive welding equipment market.