Tiger Products Co., Ltd TWR-180, TWR-120 manual Setting the Mower, Hydraulic Line Support

Page 46
(SG-14)

OPERATION

OPERATION

5.2 Connecting Mower Hydraulic Lines to the Tractor

With the tractor shut down and secured in position, relieve hydraulic pressure from the tractor by moving the control levers back and forth several times or placing the levers in the float position. Keep mower hydraulic lines, hoses, quick couplers, and swivels free of contamination. Never leave a disconnected hose end open and cap the tractor hydraulic outlet ports when not in use. If the tractor ports or mower hydraulic hose ends become contaminated, wipe clean with a rag before connecting.

Hydraulic Line Support

After connecting the mower hydraulic lines to the tractor, support the hoses with the equipped brackets. Ensure that hoses do not contact the driveline, do not bind while turning, and do not become pinched or kinked.

Hydraulic Cylinder Priming

Hydraulic Cylinders must be filled with hydraulic oil before removing the wing transport pins to lower the mower wings and deck. Hydraulic cylinders and lines are filled by holding the valve control levers in the raised position until the cylinders fully retract (wing cylinders) and extend (center cylinder). Place control levers in the float position and repeat process several more times to purge all air from the system. Ensure wings are entirely supported by the cylinders before removing the transport pins. NEVER drive out pins and NEVER remove transport pins that have tension on them.

6. SETTING THE MOWER

Properly setting the cutting height is essential for efficient and safe operation. A properly set mower will make a more uniform cut, distribute clippings more evenly, require minimal tractor work, and follow the contour of uneven terrain. Note: Avoid very low cutting heights, striking the ground with the blades gives the most damaging shock loads and will cause damage to the mower and drive. Blades contacting the ground may cause objects to be thrown out from under the mower deck. Always avoid operating the mower at a height which causes the blades to contact the ground.

DANGER! Never work under the Implement, the framework, or any lifted compo- nent unless the Implement is securely supported or blocked up to prevent sudden or inadvertent falling which could cause serious injury or even death.

TWR-180 / TWR-120 12/04

Operation Section 4-12

© 2004 Alamo Group Inc.

Page 45 Page 47
Image 46
Page 45 Page 47
Contents TWR-180 TWR-120 To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety SafetySafety SG-10 Abide by the following rules Keep Away from Rotating Elements to prevent entanglement Possible serious injury or deathImplement, an operator on prescription or over-the-counter Straighten or Weld on Blades Since this will Likely Stop Mowing if Passersby are Within 100 Yards Unless Wait a minute...Save a life Or even death. STI-4 Parts InformationSafety QTY Description TWR-180 / TWR-120 12/04 Safety Section See Inside Fornt Cover Serial Plate Safety On 10 Units Only TWR-180 / TWR-120 12/04 Safety Section TWR-180 / TWR-120 12/04 Safety Section Safety Federal Laws and Regulations Page Introduction Section Introduction IntroductionAssembly Section General AssemblyConnection to Tractor Wing Lift Spacer Plates Driveline Shield Chains Adjustable SkidsCenter Wheel Standard Spacer Plates Laminated TiresCenter Section Wheel Standards Transport Light Kit Hydraulic Phasing Cylinders Rephasing GrooveSpool Valve Kit Operation Section Operation Operation Tiger Rotary Mower Operation InstructionsOperation Medias de seguridad. SG-3Mower Standard Equipment And Specifications Tractor and Implement. Drugs and alcohol will affect an Operator RequirementsOperator’s alertness and coordination and therefore affect Tractor Requirements and Capabilities Tractor Safety DevicesTractor Requirements Rops and Seat BeltDrawbar Tractor HorsepowerFront End Weight Tractor HydraulicsTire Spacing Power Take Off PTOTire Spacing Minimum Width Dismounting the Tractor Getting on and OFF the TractorBoarding the Tractor Falling off can result in serious injury or death . SG-10Starting the Tractor Operation Connecting the Mower to the Tractor Safety Tow ChainHydraulic Line Support Setting the MowerHydraulic Cylinder Priming Setting Cutting Height Setting Deck PitchDriveline Attachment Driveline Length CheckEngagement Check Procedure Bottoming Out Check ProcedureDriveline in maximum compressed position CV Driveline Maximum Angle Check Procedure Constant Velocity CV DrivelinePRE-OPERATION Inspection and Service Entanglement, injury or death. SRM-3Tractor Pre-Operation Inspection/Service Mower Pre-Operation Inspection/ServiceOperation Operation Driving the Tractor and Mower Traffic around you and watch out for the other guy. SG-19Brake and Differential Lock Setting Starting the TractorOperating the Mower Wings Transport PositionDriving the Tractor and Mower Crossing Ditches and Steep Inclines Foreign Debris Hazards Operating the Tractor and MowerResuming mowing. SGM-5 Bystander/Passersby Precautions Stop Mowing if Passersby are Within 100 Yards UnlessPTO RPM and Ground Speed Engaging the Power Take Off PTOFrom the blades. SRM-7 Operating the Mower Mowing . S G M Operation Disconnecting the Mower from the Tractor Mower Storage Transporting the Tractor and Mower Tires and WheelsTransporting on Public Roadways OperationOperation Hauling the Tractor and Mower Trouble Shooting Guide Maintenance Section Disassembly MaintenanceSlip Clutches Maintenance Nuts and Bolts HydraulicsHubs and Spindles Tires Blade Servicing Blade InstallationBlade Removal Blade Carrier Installation Blade Carrier RemovalMaintenance Grease Schedule Cutter Frame StorageWarranty Information TigerONE Last Word TWR-180-/TWR-120 12/04 C314TG010C

TWR-120, TWR-180 specifications

Tiger Products Co., Ltd has established itself as a leader in the manufacturing of advanced welding and cutting equipment. Among its innovative offerings are the TWR-180 and TWR-120 models, which have quickly gained attention for their superior technology, robust features, and reliable performance.

The TWR-180 is designed for high-capacity operations, featuring an impressive welding output that makes it suitable for a variety of applications in industries such as automotive, construction, and heavy machinery. One of the standout features of the TWR-180 is its dual pulse technology, which allows for precise control over welding depth and heat input. This technology not only enhances the quality of welds but also minimizes material distortion, making it ideal for intricate designs and complex assemblies.

In addition to its advanced welding capabilities, the TWR-180 includes digital control systems that provide operators with real-time feedback on welding parameters. This user-friendly interface is complemented by programmable memory settings that allow users to save specific welding configurations, thereby enhancing productivity. The TWR-180 is also equipped with a high-efficiency cooling system that prevents overheating during extended use, ensuring that the equipment remains operational without interruptions.

On the other hand, the TWR-120 is specifically tailored for smaller-scale projects while maintaining professional-grade performance. The compact design of the TWR-120 makes it easy to transport and set up, which is vital for on-site applications. It features a simplified control panel that allows for quick adjustments, making it accessible for operators with varying levels of expertise.

Despite its smaller size, the TWR-120 does not compromise on power; it is equipped with innovative inverter technology that maximizes energy efficiency while providing stable output across various welding tasks. This model is particularly appealing to small businesses and workshops looking for a reliable yet versatile welding solution.

Both the TWR-180 and TWR-120 utilize advanced arc stabilization technologies that enhance the quality of the weld, reduce spatter, and improve overall efficiency. These characteristics, combined with exceptional durability and low maintenance requirements, highlight Tiger Products Co., Ltd's commitment to delivering top-tier equipment that meets the needs of diverse industries.

In summary, the TWR-180 and TWR-120 reflect Tiger Products Co., Ltd’s dedication to innovation, quality, and user-centric design. Whether for high-capacity operations or smaller-scale tasks, these models provide exceptional performance and reliability that set them apart in the competitive welding equipment market.
Top Page Image Contents